This part is the replacement drum support roller for your dryer. The roller is approximately 3 inches in diameter and is sold individually. The main reason to replace the drum support roller is if the bearings have worn out, and the squeak when the drum turns. This is an authentic OEM part sourced directly from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Noisy
This part works with the following products:
Dryer.
This part works with the following products:
General Electric.
Part# WE03X10008 replaces these:
AP3778075, 1088999
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
5.0
Filter By Rating:
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Vonnie C - February 25, 2019
Verified Purchase
Easy repair
My appliance is back in working order .much easier than expected. Great parts service.
★★★★★
★★★★★
Frank K - January 25, 2019
Verified Purchase
Replace rear drum support roller(s)
Perfect/exact replacement
★★★★★
★★★★★
Brad P - November 18, 2018
Verified Purchase
EASY FIX
The part was easy to reference on line and came with all the necessary hardware to complete the repair.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Noise and Squeaking from Front During Drying
Front roller bearings were bad and figured to do the belt while in there. I bought the manual online which was very helpful. ?? Unplug dryer Remove 4 screws behind touch panel Tilt panel forward then up leaving wires attached Rear has 2 screws on the rear ends facing down remove them at ends Lift rear up then
... Read more forward push and top will be freed (keep on top) Front edges have 1 screw each but sharp areas watch Open door and remove x 4 screws then lift up and forward bottom has tabs each end to hold in place Wires for light and switch can stay attached, move front/door to side Exposed will be the drum brace.. I changed the x 2 rollers while the drum brace was in place. To undo the rollers you have to use a wrench to reach in as you use a nut driver to remove then re-install new roller with washer on inside and outside (pay attention when you remove) Remove x 4 small screws..... hold drum inside then lift brace up and forward Have assistance hold drum steady with pressure to the back otherwise you will have to align back to the rear rollers Reach into the bottom for the idle pulley to remove drive belt tension... drive belt is VERY SKINNY and has ribbed side that faces the drum. Reverse the steps..
Pulled top covers puller front panel pulled drum forward pulled plastic clips installed rollers and put back together
Cary from WEST JORDAN, UT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
There was a grinding noise while the dryer was being used.
We removed the top and front of the dryer and found that the drum roller bearings had gone out on one side. All this happenend on a weekend with no reair store open. We googled the cut sheet for the dryer, found the part number we needed and ordered the parts (we went ahead and replaced both rollers) from partselect.com. For $70 and our o
... Read morewn labor, we completed the repair by Wednesday evening. I feel certain we saved at least $100 if not more by doing the work ourselves.
Read less
Dan from Mineola, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
35 of 54 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Todd
February 21, 2018
How do you get the dryer panels off to access the inside of the dryer for replacing parts?
For model number DPGT750EC2WW
Hi Todd,
Thank you for your question. There is a video on our website that you can reference on how to remove the panels. The dryer in the video may not show exactly like the one you have and the part being installed in the dryer is a drum glide, but it will give you a general idea on how to remove the panels. You will find the video under part number PS11741931. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Angel
February 5, 2019
The dryer won't turn when I press the start button. It makes the noise like it wants to but, it does not. Sometimes I turn the drum manually and then press the start button, then it works. Not sure what the problem is.
For model number DPGT750EC1PL
Hello Angel, Thank you for the question. I suggest checking the Drive Belt, PartSelect Number: PS959966. Sounds like it is wore out and is slipping and may need to be replaced. Thank you for your inquiry, good luck with this repair!
