Dishwasher Heating Element W10703867

Hi Ronald, Thank you for your question. There is a video on our website that you can reference on how to install the heating element. The dishwasher in the video may not show exactly like the one you have, but it will give you a general idea on how to install the part. You will find the video under part number PS2355742. I hope this helps. Thank you and have a great day!

Hello John, Thank you for the question. It woudl be best to replace the element. The element nuts, PartSelect Number PS11755402, Rubber Washer PartSelect Number PS11743934, Shield PartSelect Number PS11753266 and retainer PartSelect Number PS11741626. These parts are not included with the new element PartSelect Number PS9494999. Hope this helps!

Hello Roberta. Thanks for your question. I do know that rinse aid is very important to your appliance being able to dry your dishes properly. If you are using rinse aid then the problem might lie in your control board. The electronic control board is PartSelect Number: PS11737960- this is rarely the issue, but it could be worth cutting off power to the dishwasher for one minute and then restarting it to see if that fixes the issue before replacing the board. I hope this helps.

Hi Kim , Thank you for your question. That would be the first part that I would suggest checking. You should test this part with a multi meter to see if it is working correctly. You may also want to test your thermal fuse as well. I hope that helps. Good luck with your repair.

Hi Chris, Thank you for your question. Unfortunately the manufacturer does not give us exact specification on their parts. However this part is approximately: 15" x 13" front to plug in terminals. I hope that helps. Good luck with your repair.

Hello Joanne and thanks for writing. You can test the heating element with an ohm meter it should have continuity. We hope this helps. Please contact us anytime.

Hi Michel, Thank you for your question. If your multimeter is showing a reading of zero, then you will need to replace the heating element in your dishwasher. I hope this helps. Thank you and have a great day!

Hello Sri, Thank you for your inquiry. To pull the dishwasher out from under the countertop. Shut off the electricity at the breaker. Tip: place a piece of tape over the breaker switch to ensure no one turns it on while you're working. Turn off the water under the sink. Take off the front cover at the bottom of the dishwasher to expose the wiring. Use a voltage meter to test the wires at the dishwasher to ensure the power is still off. Remove the electrical box from the unit. Unscrew the wire nuts and pull apart the wires. Start with the green wires, white and then black. Disconnect the drain line from the dishwasher and the water supply line from the dedicated dishwasher stop. Open the door to the dishwasher, then remove the screws secured to the underside of the countertop. Raise the legs using a wrench. Slowly pull out the dishwasher ensuring the wires are out of the way. Also, the drain line should come out with the dishwasher from under the sink. Tip: Place a drop cloth or piece of cardboard in front of the dishwasher to prevent scratches on the floor. Also, before turning electricity back on, make sure to tape or cap off the ends of the three exposed wires. Although we do not have a repair video for this exact model for the heating element, I have included a video link for a similar Whirlpool heating element. Hope this helps! https://www.youtube.com/watch?v=Co8dQ7rzTMQ&index=25&list=PLD984081941E1E8CD

Hi Barb, Thank you for your question. I do know that rinse aid is very important to your appliance being able to dry your dishes properly. If you are using rinse aid then the problem might lie in your control board. I hope that helps. Good luck with your repair.

Hello Joe. Thanks for your question. The issue could be the electronic control board is PS11731265 - this is rarely the issue, but it could be worth cutting off power to the dishwasher for one minute and then restarting it to see if that fixes the issue before replacing the board. The heating element should read between 8 and 30 ohms. If the element is testing good, I would suggest checking the thermostat, part number PS11750035. I hope this helps!