Fuel Line Fitting 530023877 | Official Poulan Part | Fast Shipping | PartSelect
Fuel Line Fitting – Part Number: 530023877
Fuel Line Fitting – Part Number: 530023877 https://partselectcom.azureedge.net/Schematics/Husqvarna/128C_(2010-08)_WW_2.gif

Fuel Line Fitting

Troubleshooting

This part works with the following products:

Chainsaw, Hedge Trimmer, Trimmer, Leaf Blower / Vacuum.

This part works with the following brands:

Poulan, Jonsered, Weed Eater, Husqvarna.
Questions and Answers
Ask our experts a question on this part and we'll respond as soon as we can.
Customer Repair Stories
Average Repair Rating: 2.3 / 5.0, 1 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mark from LYNDONVILLE, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Parts Used:
530071835, 530069247, 530069216, 530037793, 530023877, 530095646
Deterioration of fuel line system
Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark
44 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
1 Review
5
out of 5
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS9469715
Manufacturer Part Number: 530023877
Brand
Model Number
Description
Husqvarna
128C
Trimmer - Trimmer/Edger
Husqvarna
128CD
Trimmer - 28cc Gas Line Lawn Trimmer
Husqvarna
128LD
Trimmer - Trimmer/Edger
Husqvarna
128R
Brush Cutter - Brushcutter
Poulan
1800
Chainsaw - Gas Chainsaw
Husqvarna
18H
Hedge Trimmer - Hedge Trimmer
Poulan
1900
Chainsaw - Gas Chainsaw
Poulan
1950
Chainsaw - Gas Chainsaw
Poulan
1950LE
Chainsaw - Gas Chainsaw
Poulan
1975
Chainsaw - Gas Chainsaw
Poulan
1975LE
Chainsaw - Gas Chainsaw
Poulan
2000
Chainsaw - Gas Chainsaw
Jonsered
2035
Chainsaw - Chain Saw
Poulan
2050
Chainsaw - Gas Chainsaw
Poulan
2050LE
Chainsaw - Gas Chainsaw
Poulan
2050WT
Chainsaw - Gas Chainsaw
Poulan
2055
Chainsaw - Gas Chainsaw
Poulan
2055LE
Chainsaw - Gas Chainsaw
Poulan
2075
Chainsaw - Gas Chainsaw
Poulan
2075C
Chainsaw - Gas Chainsaw
Poulan
2075OC
Chainsaw - Gas Chainsaw Gas Chainsaw
Poulan
2150
Chainsaw - Gas Chainsaw
Poulan
2150LE
Chainsaw - Gas Chainsaw
Poulan
2155
Chainsaw - Gas Chainsaw
Poulan
2175
Chainsaw - LE Gas Chainsaw
Poulan
220le
Chainsaw - Gas Chainsaw
Poulan
222
Chainsaw - Gas Chainsaw
Poulan
2250
Chainsaw - Gas Chainsaw
Poulan
2250LE
Chainsaw - Gas Chainsaw
Husqvarna
23
Chainsaw - Compact Chainsaw