Quick Question!

Have you ever purchased from PartSelect.com before?

900236-1-S-Frigidaire-5303937186        -Igniter
900236-1-S-Frigidaire-5303937186        -Igniter 900236-2-S-Frigidaire-5303937186        -Igniter 900236-3-S-Frigidaire-5303937186        -Igniter https://www.partselect.com/Schematics/Frigidaire/DBHHKCTB.gif

Igniter

Your Price

$20.11
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS900236
Manufacturer Part Number 5303937186
Manufactured by Frigidaire

The burner igniter is used in dryers and activates or lights the gas burner to heat the dryer during a cycle. *Please note: Do not handle this igniter by the gray part, because it is fragile. If your dryer is producing no heat, not enough heat, or it will not start, replacing this part may be the solution. Tools required for this repair project are: putty knife, screwdriver, and wrench. Remember to unplug your appliance from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

This part works with the following brands: Frigidaire, Kenmore, Kelvinator, Gibson, Tappan, Westinghouse, Electrolux.

This part works with the following products: Dryer, Washer Dryer Combo.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Will Not Start.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 5 reviews What's this?
1-5 of 5
 

60 of 70 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Dirk from Sonoma, CA

Dryer won't stay hot, gas smell

Pulled unit out from wall to access back panel. Top needs to be removed to get to the screws that hold on the front panel and door. These need to be removed to get to the valve and burner.

Once your in, the sensor, thermostat, and igniter are right up front. Sensor and thermostat were easy, the igniter breaks very easily...how do I know? Cause I broke the one I bought and had to get a new one.

I also replaced the coil set for the gas valve, because I had read that they can go bad and cause a gas fume smell. The coils are cheap, so you may as well as do them at the same time.

Anyway, once the repair was complete, I reassembled the unit and hooked up the vent.

Runs like new, and the clothes dry quickly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 22 people found this instruction helpful

Parts Used:
  • Igniter
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Wrench set
Customer: Hui from Chicago, IL

Not heat from the dryer

First of all, let me thank your wonder web site and service.


Here is the step-by-step procedure:


Unplugged the power.

Accessed the heater assembly from the front left lower corner.

Turned off the small gas valve.

Unscrewed the copper nut connecting the small gas valve and the heater assembly.

Disconnected the 3 wire connectors.

Unscrewed 2 screws under the heater assembly.

Took out the heater assembly.

Unscrewed the screw for the igniter assembly.

Installed the new igniter assembly. Be very careful with the M shaped coil. I broke a new one. That is why I have order the same part twice. But it still cost me less for hiring a tech or buying a new dryer.

Carefully put the heater assembly back into it position.

Connected the gas connector.

Secured the heater assembly to the bottom of the dryer with 2 screws.

Connected 3 wire connectors.

Turned on the small gas valve.

Plugged in and ran a test.

It worked!!.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 16 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Customer: Deborah from Kensington, CT

Dryer get hot on first start up and when up to temp it woulden get hot

because the parts were not to bad in price i canged the egnighter the coils and the thermostate, I changed the sensor and that was not the problem so after i purchest the parts mentioned above it fixed the problem
i first removed the 2 phillips screws holding the egnighter and removed the old egnighter two phillips screws and installed the new one and i removed the two philips screws holding the plate on the coils and removed the wires and installed the new coils, to the right the thermostate in the fan assembley removed tthe two phillps screws removed the wires and installed the new one reassemble the dryer and good to go I couldent beleve how fast the parts came in like the next day Thank you Parts select

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Very Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Wrench set
Customer: Matthew from JOLIET, IL

No heat

Raise the top and remove the front panel assembly. One philips screw, 24mm gas line coupler and 3 electrical connectors frees the burner assembly. Slid the old igniter out and the new one in.2 philips screws to remove the coil retainer and replace the coils.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 8 people found this instruction helpful

Parts Used:
  • Igniter
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Wrench set
Customer: randall from Athens, TN

My igniter seemed to be bad, but I really didn't know for sure. After asking advice from one of the subscribers at partselect, I decided to give the repair a try.

The appliance is gas, which made me a little nervous. However, knowing that I had the gas off, I carefully began disassembly. The burner unit is a very simple set up and within a few minutes I had the entire assembly out and noticed that in fact the igniter was broken. I ordered a new one from partselect.com and it was delivered in 2 days! The worst part of the assembly was when I accidentally bumped the new igniter against the underside of the dryer and broke the brand new one!!!..So, I ordered a second igniter and 2 days later installed it in about 30 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5

Model Cross Reference

This part works with the following models:

PartSelect Number: PS900236
Manufacturer Part Number: 5303937186
Brand Model Number Description
Kenmore41759012890Dryer - Kemore Dryer 41759012890
Frigidaire41759022890Dryer - Gas
Kenmore41779042990Dryer
Kenmore41779042991Dryer
Kenmore41779052990Dryer
Kenmore41779052991Dryer
Kenmore41788989100Dryer
Kenmore41788989800Dryer
Kenmore41790032990Dryer
Kenmore41790042990Dryer
Kenmore41790042991Dryer
Kenmore41790052990Dryer
Kenmore41790052991Dryer
Kenmore41790142000Dryer
Kenmore41790862990Washer Dryer Combo
Kenmore41790862991Washer Dryer Combo
Kenmore41790862992Washer Dryer Combo
Kenmore41790872990Washer Dryer Combo
Kenmore41790872991Washer Dryer Combo
Kenmore41790872992Washer Dryer Combo
Kenmore41791042000Dryer
Kenmore41791042001Dryer
Kenmore41791052000Dryer
Kenmore41791052001Dryer
Kenmore41791142000Dryer
Kenmore41791142001Dryer
Kenmore41792042100Dryer
Kenmore41792042101Dryer
Kenmore41792042102Dryer
Kenmore41792052101Dryer