The pump ejects the water from the dishwasher through the drain hose.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Not draining | Noisy | Will Not Start
This part works with the following products:
Dishwasher.
Part# 00611332 replaces these:
AP4339596, 611332
Customer Reviews
Average Rating:
★★★★★
★★★★★
8 Reviews
4.5
Filter By Rating:
5 Stars
7
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
1
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Frank B - August 13, 2023
Verified Purchase
Washing machine problem.
Your video showed how to replace the pump. It was simple.
Your site info indicated the three likely sources of the problem. The pump was the most likely.
Have used your website to fix several problems. Highly recommend reviewing your site before going out for repair.
★★★★★
★★★★★
Carlisa D - November 19, 2022
Verified Purchase
The part easy to install
The part was easy to install, had my dishwasher up and running in no time.
★★★★★
★★★★★
Charles W - October 1, 2019
Verified Purchase
Good Part
Was easy to replace. Did not need to pull out dishwasher.
★★★★★
★★★★★
SCOTT C - June 19, 2019
Verified Purchase
Pump is faulty
Ordered new
Water pump for dishwasher. It worked as good as the broken one.
June 19, 2019
Hello Scott,
Thank you for leaving a review on the part ordered. I have sent you an email in regards to the order. Hope to hear from you!
★★★★★
★★★★★
James G - April 22, 2019
Verified Purchase
Dishwasher pump replacement
The pump fit perfectly and works well. It solved the problem. Thank you.I especially appreciate the video which assisted the installation.
★★★★★
★★★★★
Mark W - June 15, 2018
Verified Purchase
Quick Refund
Did not need the part, but the return process was very easy and I got a quick refund.
★★★★★
★★★★★
Gene B - May 18, 2018
Verified Purchase
Fast service
Received part in 2 days. Worked to fix dishwasher. A little expensive but did the job.
★★★★★
★★★★★
Hoyt C - February 17, 2018
Verified Purchase
Replacing Drain Pump In Bosch Dishwasher
The replacement pump was an OEM replacement, as it fit perfectly. Replacement was easy, simply by removing metal kick plate, then removing the lower part of the outer door. Access was adequate to replace the old pump with a simple quarter twist and removing the control wire. The new pump fit perfectly, and performed as expected upon replacing the door face and the kickplate and starting it up.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
E-24
Removed old discharge pump and replaced it with the new one. After four attempts the dishwasher worked once. This cycle continued for the next 3 attempts then it stoped all together. Ordered the sensor, installed it snd the dishwasher still doesn’t work! Now what do I do???
Dishwasher would not start and had not completely drained.
Tried the door lock first. Did not fix the problem.
Replaced the drain pump and it fixed the problem.
Parts Select identified the pump as the most frequent problem.
Next time I will order both parts when one is cheap for any repair.
Find Parts Select is very helpful. They have identified a probl
... Read moreem with a washing machine in the past.
I will use them for future problems.
Read less
Frank from WESTMINSTER, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
15 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ben
November 12, 2019
Hi, is there a way to test this pump to see if it is bad before buying a new one? I know i should use a multimeter, but this part does not have two prong to touch the leads to. It has a single plastic clip/wire attachment. Pump seems to cycle on and off not fully draining water from the bottom.
For model number SHE3AR52UC/21
Hello Ben and thanks for writing.
How do I know if my dishwasher drain pump is bad?
First, check the drain hose, sink drain and sump to ensure nothing is blocked. If the path is clear yet your drain pump is continually failing to pump out water, the pump has failed. If you notice that your drain pump has visible signs of damage including cracks or dents, or if it has failed, it needs to be replaced. We hope this helps. Please contact us at any time
8 people found this helpful.
Was this helpful?
Thank you for voting!
Theresa
March 6, 2018
Dishes are spotted or not completely clean
For model number 63013903011
Hi Theresa, Thank you for the question. The first thing to check is the soap dispenser to make sure it is opening and all of the detergent is coming out. You can also check the spray arms to see if the holes the water sprays through are clear. It is common for them to get clogged over time. You can try to run a empty load and add a cup of vinegar to the water and it will help clean the spray arms. Next you can you start the cycle and after the water fills, open the door to see if the water is at the proper level and the water should be fairly hot so there should be lots of steam. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Jerry
August 8, 2018
When the dishwasher is turned on, there is a continuous sound (could be a motor) for about 2 minutes, then the washer displays an error of e24 and fails to wash. I have cleaned filters, checked drain hose and all is clean. Is this likely a pump problem? Or are there other possibilities? Thanks
For model number SHE6AP05UC/03
Hi Jerry, Thank you for your question. From the sounds of it, the pump can be one of the issues when you are getting the E24 error code. However you may have to take a look at your sensors as well. If those parts are all working, the problem may be in your electronic control board. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Simon
September 3, 2021
Hi! The dishwasher is not draining properly. The pump seems noisier than usual. I can see the pump spinning when I pull the float up. It seems in good condition. The hose is free all the way. The flap valve is good. Can it be the pump even if it spin?
For model number SHE3AR55UC
Hello Simon , Thank you for the question. Yes, the impeller can still spin on a defective pump. The Drain Motor could be weak or defective and not able to suck the water through to the drain hose. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
John
October 12, 2021
There is a brief grinding sound then the drain pump engages, does not drain all the way. I’m assuming it’s the pump, how difficult of a job is it to replace? I’m fairly mechanically inclined.
For model number SHX4AP05UC/02
Hello Jon, Thank you for the question. Once the appliance is unplugged and removed from the cabinets you just need to tip the dishwasher back to access the pump. Most customers have been able to do the repair on their own and it is good to heave a second set of hands. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Stephen
November 8, 2023
Have troubleshot, won’t drain and won’t run. Suspect the pump. Where can I learn how to replace the drain pump? Degree of difficulty?
For model number SHE4AMI15UC/01
Hi Stephen, thank you for the great question. Based on our understanding, the issue is possibly because of the drain pump, part number PS8727352. Replacing the drain pump is easy and can be done at home. The drain pump is located at the bottom of the dishwasher. Un-thread the screws on each side of the door that hold the outer panel, and remove the panel. Remove the access panel by un-threading the screws. Once you removed the access panel, you will have access to the drain pump. Take the wire harness out of the connector. Press in the locking tab on the top and turn the pump clockwise to remove it. To install the new pump, you may follow the instruction backward. We hope this solves your problem!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Don
April 24, 2024
Getting the E24 error code on Thermador DWHD651GFP/01 dishwasher. Did all the basic trouble shooting - checked the filter, checked the drain hose etc. Turned power off and worked once. Then back to E24 error. Disconnected power cable to drain pump and unit worked once, then back to E24 error. Removed drain pump and tested w/ voltmeter and got a reading of ~.0.92 with tone (not sure what to look for). Pump doesn't look damaged or worn out. Put back on and worked once then E24 error. Removed pump and reinstalled, worked once, then E24 error. Tried removing/replacing pump again and this time won't work. Tried new pump and it worked once then E24 error. Is it a control board? A sensor? What next?
For model number DWHD651GFP
Hello Don, thank you for your inquiry. According to our research, the error code E24 means that the dishwasher is not draining properly because the drain filter is blocked. If you have checked the filter and it is fine, then the issue is most probably with the drain pump, part number PS8727352. You may need to replace it to fix the issue. Glad to be of assistance!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Larry
January 7, 2020
The black gasket around the pump assembly is broken. The dishwasher is leaking and has lots of suds. Can we get that part?
For model number SHE4AM -Bosh
Hello Larry, thank you for your question. That gasket is only available by ordering the drain pump itself. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
James
April 1, 2019
Is there a way to check the pump impeller to see if it is blocked or broken? I can't figure out how to access it.
For model number SHE6AF02UC/03
Hello James, Thank you for the question. The pump will need to be removed from the appliance to access the impeller. Thank you for your inquiry, good luck with this repair!
Was this helpful?
Thank you for voting!
Steve
December 29, 2017
Is there a way to test this drain pump once it's out of the dishwasher. I've cleaned the sink drain, installed a new garbage disposal checked the drain hose for blockage, checked and cleaned the flapper valve in the drain hose, and the dishwasher drains intermittently. I've removed the pump and all looks clear. Is there a way to test to see if it runs properly. The impeller shaft turns easily. I hate to buy a new pump if not needed, but can't think of anything else short of a whole new dishwasher and this one isn't all that old; 2 yrs Max.
For model number she3arf2uc/21
Hi Steve, Thank you for the question. In order to test the pump you will need a Multi Meter to check for continuity. Hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
