The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences. Includes mounting screws.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Robert B - August 5, 2023
Verified Purchase
Timer for wash machine
That was the part I needed,my wash machine is operating once again,very pleased!
★★★★★
★★★★★
Stephen Y - February 26, 2022
Verified Purchase
Worked great.
Easy to replace.
★★★★★
★★★★★
Mike S - March 23, 2019
Verified Purchase
Roper washer timer
Part came quickly Had more problem figuring out how to get covers off to timer. Once to timer 2 screws and a power connector was done in 20 minutes. washing machine was not draining. working now.
★★★★★
★★★★★
Robert O - September 26, 2018
Verified Purchase
Exact factory replacement - recommended resource for appliance parts based on my first order.
PartSelect had the lowest unit price and offered the lowest shipping rate price. My phone call was promptly answered by energetic and helpful support. I had other choices on line and gave PartSelect a try. This new replacement part was from the original manufacture, installed it, and it worked. Thank you.
★★★★★
★★★★★
Christopher S M - July 4, 2018
Verified Purchase
RETAINING PART
Washer seems to be working correctly now; will retain part for future repair
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.5 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Timer had stopped advancing.
Watched several YouTube videos on timer replacement. Although the specific model of my washer was not found, the general steps were sufficiently covered. Unplugged the washer from the electrical outlet. Unscrewed (ccw) the control knob. Removed the indicator plate and the control retainer piece. Removed the screws on the panel (that
... Read morehold the timer in place). Removed 2 screws from end caps. Flipped up the control panel. Unplugged the timer unit. Installation was these steps performed in reverse. It was really easy!!
Read less
Wesley from BETHANY, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
timer knob would not stay out , broken...!!!!
as a 35 year AUTO / TRUCK tech , it was a no brainer. saved a service call/ charge !!!!!. part was correct , NEW TIMER installed !!! , back up and running.THANKS !!! HAPPY WIFE, HAPPY LIFE....
scott from milford, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
9 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not wash on "normal" cycle. Had to play with the knob to get it to run at all. Washer would not drain properly either.
I unplugged the washer from the electrical outlet.
I then removed the drain hose from the wall drain to allow me to turn the washer to gain access to the the back panel.
From the front, I then removed the plastic timer knob from the timer by unscrewing it. Then I pulled the plastic plate with the arrow on it to re
... Read moremove it. This exposed the screws that attached the timer to the control panel. I left them attached.
I then removed the two screws on the bottom of the front of the control panel (on each end) that attach the control panel to the washer.
I then went to the rear of the washer and removed the two screws on the top of the rear of the control panel.
I went back to the front and pulled the control panel forward and up to release it from the washer.
I then removed the two screws (that were under the plastic plate) that attached the timer to the panel and removed the timer from the panel.
Then I unplugged the wiring harness from the timer and removed the timer completely.
From there I reversed the procedure to install the new timer and knob.
First I removed the two scews that hold the front panel in place. I then turned the knot counterclockwised to loosen it and I used the flat tip scew driver to pry the clear plastic ring that was underneath the knot. I then removed two screws that hold the timer to the panel. I then flip the panel to the other side to disconnect the connec
... Read moretor to the timer. I then pluged in the new timer and reversed the sequence.
Read less
Alan from Madison, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
14 of 22 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Toni
May 2, 2023
Washes... doesn't engage further.
For model number LSQ9544KQO
Hi Toni, thank you for reaching out. We believe the issue is most likely with the washer timer, part number PS11742046, and you may need to replace it to fix the issue. We hope this solves your problem!
My Whirlpool washer does not spin at the heavily soiled cycle. What is the problem?
For model number LST7233AW0
Hello Leonard, thank you for inquiring. For this symptom you will want to replace either the Clutch Assembly part PS334641, the Direct Drive Motor Coupling part PS1485646, or the Agitator Repair Kit part PS334650. We hope this helps.
Was this helpful?
Thank you for voting!
Michael
December 10, 2021
put on new timer washer works but do not complete a cycle and do not turn off
For model number 11092284100
Hi Michael,
Thank you for your question. If your washer does not complete a cycle and it will not turn off, and you have just replaced the timer, check and make sure that it is connected correctly and test it with a multimeter for continuity to see if it functioning properly. If the timer is fine, you should also check the lid switch, the pump, the water level switch and the water pressure hose. We have included a link that you may reference for information on how to check these parts. We hope this helps! Good luck with the repair!
Hi John, thank you for the question. Taking a closer look at the following parts will help you fix your problem: the high-limit thermostat, part number PS11741441, the thermal cut-off kit, part number PS334278, the cycling thermostat, part number PS11741405, and the heating element, part number PS11741418. We hope this helps!
