This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking | No hot or cold water
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Crosley.
Part# 134211400 replaces these:
AP3267279, 1014350
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
the cold water would not stop from draining into the wash tub
unscrew the top from the back. lift it up. Support the top and then unplugged the old valve, unscrewed it took the drain hose off it and presto the old came right out. align the new one was a little tricky and attached the drain hose and tightened the screw hook up the wires reattach the top and I was done. 30/45 minutes. I was really sur
... Read moreprized that the part I ordered was the same one I took out. Thanks for being there.
Read less
william from goldsboro, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
44 of 65 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Melissa
February 27, 2019
After my wash is done water still drips out of the water area and my closes are soaked again if i don't take them out asap. I can turn off the water valve in the back on the wall and the water stops coming out so is that a bad water valve?
For model number fex8310cs0
Hi Melissa,
Thank you for your question. If there is water leaking into the washer after the washer has been turned off, then the issue is with the water inlet valve and it will need to be replaced. I hope this helps. Thank you and have a great day!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Melissa
February 27, 2019
Thanks for answering my question about my leak and letting me know that it is the water inlet valve. Is that the same as the water valve or it that something different? And if it is different do you know the part number i need to order? Thanks so much!
For model number fex8310cs0
Hello Melissa, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PS815534. Have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Curtis
November 27, 2017
Is there anywhere I can watch a video, or read the procedure for accessing the water inlet valve on a Frigidaire washer/dryer combo? This is a stacked unit and accessing the water valve seems complex due to the stacked nature of the unit. There is no easy access to the rear of the lower cabinet, as there is in with most washers. I simply need to know hot to get to the water valve. Back plate doesn't come off independently, nor does the right side, as you're looking at the unit. Help!
For model number FGZ831AS2
Hi Curtis,Thank you for the question. To access the water valve you need to remove the 2 screws at the bottom of the front panel and pull the front panel forward from the bottom to release the panel.Once the panel is removed there should be a screw on either side that will allow you to remove the main top. The water valve is located on the back wall on the right hand side. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Connie
March 8, 2018
My washer is filling up very slowly? It never did before. I do have sulfa water? Do i need to clean something that might be plugged with something? I have had this washing machine since 2006. Thank you for your time. Sincerely, connie
For model number GLWS1233AS2
Hello Connie, thank you for your question. It sounds like the water inlet valve screens are clogged. You can try to clean them out but they are quite difficult as the screens don't actually come out of the valve, you'd have to do your best cleaning job on them when the screens in the unit. Usually we recommend customers replace the valve when the water flow starts to decrease. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ralph
April 12, 2018
This is a stackable unit. Do I have to remove the upper dryer unit? Thanks.
For model number Glet1031cs0
Hi Ralph, Thank you for the question. Since the top needs to be removed to access the valve the dryer will have to be also removed. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Raymond
December 14, 2019
Water keeps dripping into the tub
For model number fws87800ds0
Hello Raymond and thanks for writing.
It certainly sounds like a faulty water valve PS815534 test the part and replace it if needed. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
Dwip
March 22, 2022
The drum is dripping water even when the machine is off (and ends up with a couple of inches of water over time). Will replacing the inlet water valve fix this issue
For model number GLET1142CS0
Hi Dwip,
Thank you for your question. If there is water filling the tub when the washer is not in use, then a component in the water inlet valve has failed and it will need to be replaced. The part number listed under your model number for the water inlet valve is PS815534. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
