Part Location Diagram of 134190200 Frigidaire Water Inlet Valve
See part 41 in the diagram
Replacing your Frigidaire Washer Water Inlet Valve
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Water Inlet Valve 134190200

 Fits your LT100PXD-3!
★★★★★
★★★★★
12 Reviews

Rated by 29 customers 

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.

$ 127.53
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your LT100PXD-3!
PartSelect Number PS815509
Manufacturer Part Number 134190200
Manufactured by Frigidaire for Frigidaire, Kenmore, Westinghouse, Gibson
Product Description

Water Inlet Valve Specifications

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Frigidaire Washer Water Inlet Valve

Replacing your Frigidaire Washer Water Inlet Valve
Troubleshooting
This part fixes the following symptoms:
Leaking | No hot or cold water
This part works with the following products:
Washer, Washer Dryer Combo.
Part# 134190200 replaces these:
AP3363282, 1014339, 00633917, 01132783, 08001821, 08006734, 08014911, 08015532, 09948913, 1132783, 131167100, 131199700, 131258000, 131389300, 3161140, 3202984, 3204379, 3261053, 5300633917, 5303202984 , 5303206933, 5303207418, 5303210628, 5303261053, 5303272066, 5303280328, 5308006734, 5308015532, 633917, 8001821, 8006478, 8006734, 8014911, 8015532, 9948913, DF141174-000, F132811, F136404, F136404-000, F137632, F140274, F140274-000, F140274000, F140560, F140862-000, F141174-000, F141174000, F76138-1, F76684, F76684-1, NQ00171447, Q000149791, Q000158951, Q000165531, Q000171301, Q000171442, Q000171443, Q000171445, Q000171447, Q000199022, Q000614163, Q171442, Q171443, Q171445, Q171447, WQ149877, WQ158951, WQ171442, WQ171443, WQ171445, WQ171447, WQ614161, WQ614163 Show less
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
12 Reviews
5.0
Filter By Rating:
  • 5 Stars
    12
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
Customer Repair Stories
 Average Repair Rating: 4.0 / 5.0, 29 reviews. What's this?
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing installation instruction that matched.
The water would not stop filling
First I did some research and concluded the water inlet needed replacing. Obviously once you know what you need you go to PartSelet.com for parts and installation info. I went through the front of the machine. So I removed the front of the washer(2 screws at the front bottom)slide down the panel to separate it, lifted the top cover of the washer(2 screws on the underside of the lid and 3 wire connectors to the fill switches) and then loosened the right side panel(3 screws at the bottom). Now pushing the wash barrel to the side it gave me enough room to squeeze my arms in to the inlet part. Be careful there are sharp edges and screw tips inside the machine. I removed the 2 wire connectors(hot and cold solenoids) inside the washer and then removed the screw from the back outside that holds the water inlet to the machine. Now I was able to pull the inlet closer to me so I could get pliers on the hose clamp to loosen and remove the old part. The new part was an improved version that was more solid. I attached the hose affixed the squeeze hose clamp and pushed the water inlet into place. The screws were not threading so I grabbed a couple of self taping hex head screws and a nut driver head for my drill and screwed the inlet in from the back of the washer. Then I replaced the wire connectors to the water inlet. With the water inlet complete, I reattached the right side panel, the washer lid, fill switch connectors and the front panel. Washer fixed and running perfectly!
  • Jeff from Monticello, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water not coming into machine fast.
we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing
  • Donna from Oxford, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water filling in machine without turning on
I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!
  • Christine from DALLAS, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water would not shut off causing door to pop open and spill all over the floor
The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.
  • Joe from Interlaken, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
hot water kept filling the tank
I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL
  • Bob from Birdsboro, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leaked into machine when turned off
Removed top,removed hose from inlet valve to washer,removed hot and cold inlet hoses and with phillips screwdriver removed water inlet valve assy and replaced. Reassembled and tested.

My order arrived 2 days after i ordered same. Excellent service from partselect, Thank You....
  • Henry from Frenchtown, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No hot water in machine
First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come off so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!
  • julie from minneapolis, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water valve not shutting off correctly
After the new replacement part arrived, I took off the complete back panel (after unplugging the electrical and shutting off the hot & cold water supply). I disconnected both hot & cold water hoses, unscrewed the 2 screws holding the water valve, unplugged the 2 electrical wires for the water valve sending unit, unclamped the outlet water hose. Then I reversed order with new water valve. Put everthing back together in about 20 minutes overall. I did also replace the hot & cold water supply hoses with a better quality hose. Works like new! Thank you very much.
  • Eric from Sebastopol, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water over flowing, old valve stuck open.
Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.
  • william from mayfield, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water not turning off
Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.
  • Anita from Orange, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

5 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dennis
February 5, 2018
How do I get the top off so I can get to the defective parts on a top loading washer ?
For model number FWS445RFS2
PartSelect logo
Hi Dennis, Thank you for the question. The top is held in place by clips. You can use a putty knife or a flat head screw driver to release the clips. They are located on each side of the appliance. Just insert the screw driver and depress the clip and it will release. Hope this helps!

8 people found this helpful.

Was this helpful?
Thank you for voting!
E
November 11, 2019
Hello, what does the "water intake valve" do?
For model number Fsw833as1
PartSelect logo
Hello E, Thank you for the question. The Water Inlet Valve is at the back of the appliance and the fill hoses connects to it and acts as a "gate" that opens to fill the appliance with water. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Vera
March 2, 2020
Question —. While spinning and laundry slightly off centre causes drum to wobble until it’’s in full swing. Can this be repaired? Machine is old—2003- 06.
PartSelect logo
Hello Vera, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. We are looking forward to hearing from you.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Alex
June 25, 2019
Will this fit a white Westinghouse washer.
For model number MWX233RES4
PartSelect logo
Hello Alex, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS815509. Thank you for your inquiry, good luck with this repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Jacqueline
January 25, 2022
After the snow storm my washer started running hot water and it was going into the stand the washer sits on. It looks like the water intake is cracked
For model number Frigidaire affinity
PartSelect logo
Hi Jacqueline, Thank you for your question. Before we can provide you with information on the water inlet valve, we will need the model number from from your washer. We have included a link from our website that you may reference on where to locate the model number on your washer. If you could resubmit your question with this information, we would be happy to help you. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
Additional Links:
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS815509
Manufacturer Part Number: 134190200
Brand
Model Number
Description
Frigidaire
38712
Washer - WASHER
Frigidaire
38802
Washer - WASHER
Kenmore
41724182300
Washer
Kenmore
41724182301
Washer
Kenmore
41727182700
Washer
Kenmore
41729022890
Washer
Kenmore
41729042990
Washer
Kenmore
41729042991
Washer
Kenmore
41729042992
Washer
Kenmore
41729052990
Washer
Kenmore
41729052991
Washer
Frigidaire
41739012890
Washer - Stackable
Frigidaire
41739012891
Washer
Frigidaire
41739022890
Washer
Frigidaire
41739022891
Washer
Kenmore
41740032990
Washer
Kenmore
41740042990
Washer
Kenmore
41740052990
Washer
Kenmore
41740142000
Washer
Kenmore
41741042000
Washer
Kenmore
41741052000
Washer
Kenmore
41741142000
Washer
Kenmore
41742042100
Washer
Kenmore
41742052100
Washer
Kenmore
41742142100
Washer
Kenmore
41743042200
Washer
Kenmore
41743042300
Washer
Kenmore
41743052200
Washer
Kenmore
41743142200
Washer
Kenmore
41743142300
Washer
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service