Quick Question!

Have you ever purchased from PartSelect.com before?

815509-1-S-Frigidaire-134190200         -Water Inlet Valve
815509-1-S-Frigidaire-134190200         -Water Inlet Valve 815509-2-S-Frigidaire-134190200         -Water Inlet Valve 815509-3-S-Frigidaire-134190200         -Water Inlet Valve https://www.partselect.com/Schematics/Frigidaire/14Q3NVCV.gif

Water Inlet Valve

Your Price

$19.48
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS815509
Manufacturer Part Number 134190200
Manufactured by Frigidaire

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.

This part works with the following brands: Frigidaire, Kenmore, Gibson, Kelvinator, Westinghouse, Tappan, Crosley, Electrolux, Uni.

This part works with the following products: Washer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Will not stop filling with water.
  • Leaking.
  • No hot or cold water.
  • Will not fill with water.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 29 reviews What's this?
1-15 of 29
 

70 of 78 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: alvaro from east hampton, NY

Washer continued to fill to point of overflow

First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 16 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Howard from Lcolnton, GA

Water continued to flow into machine during spin cycle

After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, disconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

13 of 14 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Mark from Pittsburgh, PA

No cold water

Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have clean clothes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 11 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Dominick from Las Vegas, NV

No hot water to washing machine

S/O Water , Removed front panel, removed screws from side panel water valve accessible. Removed screws that hold water valve, installed new valve reassembled washing machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 9 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Eric from Sebastopol, CA

Water valve not shutting off correctly

After the new replacement part arrived, I took off the complete back panel (after unplugging the electrical and shutting off the hot & cold water supply). I disconnected both hot & cold water hoses, unscrewed the 2 screws holding the water valve, unplugged the 2 electrical wires for the water valve sending unit, unclamped the outlet water hose. Then I reversed order with new water valve. Put everthing back together in about 20 minutes overall. I did also replace the hot & cold water supply hoses with a better quality hose. Works like new! Thank you very much.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 8 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Steven from Oklahoma City, OK

Leaking water inlet valve

removed the two 'lock down flanges' from the back of the machine, lifted the top from the front and slid it forward to access the valve. Removed the two electrical connections then the compression ring from the hose on the output side. Removed two screws holding the valve in place, then reversed the process.

I wish this valve was made of metal rather than plastic. I had to replace it because the threads were stripped. Here's the heads up. Make sure the fittings on your supply hoses are 'clean' or you'll mess up the plastic threads and not get a good seal.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Alan from Denver, CO

The threaded male coupling on the water inlet valve is plastic and broke during moving.

I installed this part on a stackable washer-dryer unit. First, I removed the hoses (one had broken off already, damaging the cold water coupling). Using a nut driver I removed the screws on both L-brackets in back that help secure the dryer unit to the washer base. Then, I located 2 other screws securing the dryer to the washer base. These were fairly accessible in the recess where the dryer exhaust vent is located, directly above the water inlet valve. I removed both with a nut driver. I thought I would have to also unscrew 2 more screws on the other side of the dryer, but these were not accessible. So I lifted the side of the dryer I had unbolted to get to the water inlet valve. And voila! It lifted up. I placed a 2x4 on edge to keep the dryer tilted open. The inlet valve is attached to the back inside of the washer by a single screw on the Kenmore, which I removed with a phillips screw driver. Reaching inside the back of the washer, I disconnected the water hose by pinching the retaining clip with pliers. Then I pulled the electrical connections off the the hot and cold solenoids and the unit came out. The replacement unit was installed in reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 4 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Jeff from Monticello, NY

The water would not stop filling

First I did some research and concluded the water inlet needed replacing. Obviously once you know what you need you go to PartSelet.com for parts and installation info. I went through the front of the machine. So I removed the front of the washer(2 screws at the front bottom)slide down the panel to separate it, lifted the top cover of the washer(2 screws on the underside of the lid and 3 wire connectors to the fill switches) and then loosened the right side panel(3 screws at the bottom). Now pushing the wash barrel to the side it gave me enough room to squeeze my arms in to the inlet part. Be careful there are sharp edges and screw tips inside the machine. I removed the 2 wire connectors(hot and cold solenoids) inside the washer and then removed the screw from the back outside that holds the water inlet to the machine. Now I was able to pull the inlet closer to me so I could get pliers on the hose clamp to loosen and remove the old part. The new part was an improved version that was more solid. I attached the hose affixed the squeeze hose clamp and pushed the water inlet into place. The screws were not threading so I grabbed a couple of self taping hex head screws and a nut driver head for my drill and screwed the inlet in from the back of the washer. Then I replaced the wire connectors to the water inlet. With the water inlet complete, I reattached the right side panel, the washer lid, fill switch connectors and the front panel. Washer fixed and running perfectly!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Henry from Frenchtown, NJ

Water leaked into machine when turned off

Removed top,removed hose from inlet valve to washer,removed hot and cold inlet hoses and with phillips screwdriver removed water inlet valve assy and replaced. Reassembled and tested.

My order arrived 2 days after i ordered same. Excellent service from partselect, Thank You....

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: eliot from fairbanks, AK

Over filling

no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: John from Powhatan, VA

Inlet valve leaked water from supply line(s) back into washer.

Pulled washer electrical plug from receptacle.
Unscrewed hot and cold water inlet hose connectors.
Removed screws retaining backplate.
Removed back plate.
Removed two screws connecting valve assembly to frame.
Pulled two spade electrical wire connectors from valve assembly.
Opened hose clip securing hose on outlet side of valve assembly, using pliers.
Pulled hose from valve assembly.
Valve assembly now free.
Reversed above with replacement valve assembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: John from Willis, TX

Tank would not stop filling.

Replaced both the water inlet valve and the tank pressure switch to eliminate any possible cause. The repair was easy, and now the washer works fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Lee from Auburndale, FL

2 problems washer would not stop filling and cold water barely came out.

simply removed top of washer(where the lid is) and removed old parts and installed new ones. It was just a matter of disconnecting the hoses and electrical connections. Make sure to unplug washer first.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools:
Customer: Donna from Oxford, MA

Water not coming into machine fast.

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Christine from DALLAS, GA

Water filling in machine without turning on

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 29

Model Cross Reference

This part works with the following models:

PartSelect Number: PS815509
Manufacturer Part Number: 134190200
Brand Model Number Description
Kenmore41724182300Washer
Kenmore41724182301Washer
Kenmore41727182700Washer
Kenmore41729022890Washer
Kenmore41729042990Washer
Kenmore41729042991Washer
Kenmore41729042992Washer
Kenmore41729052990Washer
Kenmore41729052991Washer
Frigidaire41739012890Washer - Stackable
Frigidaire41739012891Washer
Frigidaire41739022890Washer
Frigidaire41739022891Washer
Kenmore41740032990Washer
Kenmore41740042990Washer
Kenmore41740052990Washer
Kenmore41740142000Washer
Kenmore41741042000Washer
Kenmore41741052000Washer
Kenmore41741142000Washer
Kenmore41742042100Washer
Kenmore41742052100Washer
Kenmore41742142100Washer
Kenmore41743042200Washer
Kenmore41743042300Washer
Kenmore41743052200Washer
Kenmore41743142200Washer
Kenmore41743142300Washer
Kenmore41744042400Washer
Kenmore41744072300Washer