Surface Burner Terminal Block Kit WB17T10006 | Official GE Part | Fast Shipping | PartSelect
Surface Burner Terminal Block Kit – Part Number: WB17T10006
( Grid squares measure 1x1 inch )
Surface Burner Terminal Block Kit – Part Number: WB17T10006 Surface Burner Terminal Block Kit – Part Number: WB17T10006 https://partselectcom.azureedge.net/Schematics/GE/00115410i01.gif

Surface Burner Terminal Block Kit

PartSelect Number PS783534

Manufacturer Part Number WB17T10006

Manufactured by GE

Product Description

Surface Burner Terminal Block Kit Specifications

This kit includes the female contact with wires, terminal block and mounting clip.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Element will not heat | Will Not Start

This part works with the following products:

Range.

This part works with the following brands:

General Electric, Kenmore, Hotpoint.

Part # WB17T10006 replaces these:

1038747, AP3203326, WB17K10003, WB17T10001, WB17T10006, WB17X10007.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
17 questions answered by our experts.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your General Electric Range Surface Burner Terminal Block Kit

Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 18 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Americus from Pittsburgh, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
WB17T10006, WB31T10011, WB31T10010
Burned out block
Watched a repairman do it the last time for $200.00. This time I unplugged the stove, unscrewed four screw nuts holding the upper rear cover, unplugged old wires, reconnected new ones, fed them thru to the front, attached them to the new block, screwed the block into place, replaced back cover, stuck the element into place, made my little brother plug it back in and turn it on first. It worked. Cost me $20.00 to do what the repairman did the last time. I also replaced the reflector pans. No-brainer.
297 of 519 people found this instruction helpful.
Was this instruction helpful to you?
douglas from louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Parts Used:
WB17T10006
burner was shorting out
unplugged unit pulled it away from wall took off the backplates traced wire to plug replaced with part ordered very smooth operation. the most impressive thing to me was i ordered part on computer and it was at my door in 30 hours awesome.
44 of 44 people found this instruction helpful.
Was this instruction helpful to you?
Monica from Point Blank, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WB17T10006
The electric burner on the stove top would no longer heat up, when we removed it we noticed that the element was completely burned. I mean fryed!
First, I got my husband and let him know that the part was in (really easy), then I sat back and watched as he pulled the oven from the wall, unplugged it and lifted the stove top (so far, I haven't broken a sweat)! I then peeped up under the top as he removed a scew from the element and then several screws from the back panel, trace the wire to the needed element, and reconnect the new element (haven't broken a nail yet)! He then secured the element back on its mount, let down the top and plugged the oven back in, checked for accuracy...mission accomplished! This was the easiest repair I've ever done!
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Brian from Marathon, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
WB30X20481, WB17T10006, WB31T10013, WB31T10012
stove top burner didn't heat
I replaced the element and socket. First, I unplugged and removed the burner element. Then, I pulled the range away from the wall and disconnected the power source. I then, removed the 4 screws that held the top back panel and removed the panel. Then, I raised the stove top, unscewed the socket, removed the tape, unplugged the wire terminals located on the terminal bock on the back of the stove and removed the socket/wire assembly. I then replaced with the new parts reversing the process. This only took about 30 mins total including cleaning the crap from behind the stove.
9 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Carol A. from Orlando, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WB17T10006, WB30M2
The terminal burner block was burned out, and surface plate not heating.
My husband removed all the old terminal block and element, and put the new one in. It was very easy. Thank you for the instructions which were included.
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Martin from plainfield, CT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
Parts Used:
WB17T10006
Front Large Most Powerful Burner's Block had broken so it didn't heat
This electric stove has a lift up top which I lifted to get at the block and follow the wire back to the terminal at the back of the the stove. I removed the 5 small lag screws holding the back in place, removed the backing followed the wires back to where they connected in the Stove On/Off Control, disconnected the two wires from the control and then laid the new part in place rethreading and reconnecting the wires. I reinstalled the block and ran a test to ensure the burner operated correctly. After successful testing I disconnect the old block holder by removing the small lag screw, replace it with a new one that came with the replacement terminal block. I then inserted the block into the new holder carefully rolled up the excess wire and wrapped it in a couple of places with electrical tape and also secured it to the side of the stove, out of the way of operation with electrical tape, put the top down, plugged it back in and put it back in place. All told the repair took about 40 minutes. I was impressed with the speed of delivery, the quality of the product, the instructions for installation and the added bonus of getting a terminal block holder as part of the repair kit! Thank You for making me look like a genius!
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Emmett J from Winchester, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Parts Used:
WB17T10006
terminal was broken due to maney uses
unscrew the terminal block,pulled the old wires out,installed the new wires installed the new block
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Marco from Santa Barbara, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WB17T10006
Two sockets for electric elements and their end terminals were badly burned.
0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!

That's it! It took about 20-30 minutes.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Roy from Chelsea, MA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Parts Used:
WB17T10006, WB03T10167
The ceramic contact housing for the burner had melted, and the back large burner started to burn.
I verified the parts that were sent to me to make sure they were what I needed. I read the instructions for the replacement of the new parts. I then moved the stove out away from the wall to access the back plate where the burner connections are located. I removed the cover plate to expose the connections. I then traced out the wires from the burner that needed to be replaced to the connections on the back panel. I disconnected the appropriate wires and tied them off on both ends because it was difficult to try and weave the old wires out and the new wires through the original channel they were running through. I removed the damaged ceramic housing and installed the new ceramic housing along with the new large burner ring. I then routed the new wires through the stove to the back connection panel and plugged them into the same positions as the old wires occupied. I then wrapped up the excess cable and tied it off and stored it inside the rear panel per the instructions. I tie wrapped the new cable along the route of the existing channel of wires from the front to the rear and then replced the back panel and secured it with the screws. I pushed the stove back to it's original position. I then tuned on the rear burner to see if was working properly, and it heated up fine.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Bayani P. from DALY CITY, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Parts Used:
WB17T10006
Burnt Terminal Block
Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
21 Reviews
4.8
out of 5
Filter By Rating:
  • 5 Stars
    19
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    1
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS783534
Manufacturer Part Number: WB17T10006
Brand
Model Number
Description
General Electric
15451-0
Range
General Electric
154510
Range
General Electric
155910
Range
Kenmore
36261101000
Range
Kenmore
36261101001
Range
Kenmore
36261108000
Range
Kenmore
36261108001
Range
Kenmore
36261741000
Range
Kenmore
36261741001
Range
Kenmore
36261742000
Range
Kenmore
36261742001
Range
Kenmore
36261748000
Range
Kenmore
36261748001
Range
Kenmore
36262492000
Range
Kenmore
36262492001
Range
Kenmore
36262780100
Range
Kenmore
36262780101
Range
Kenmore
36262780102
Range
Kenmore
36262780103
Range
Kenmore
36262781000
Range
Kenmore
36262781001
Range
Kenmore
36262781002
Range
Kenmore
36262781003
Range
Kenmore
36262781004
Range
Kenmore
36262788000
Range
Kenmore
36262788001
Range
Kenmore
36262788002
Range
Kenmore
36262788003
Range
Kenmore
36291112000
Range
Kenmore
36291112001
Range