Water Inlet Valve 242252702 | Official Frigidaire Part | Fast Shipping | PartSelect
Quick Question!

Have you ever purchased from PartSelect.com before?

Water Inlet Valve – Part Number: 242252702
Water Inlet Valve – Part Number: 242252702 Water Inlet Valve – Part Number: 242252702 Water Inlet Valve – Part Number: 242252702 https://partselectcom.azureedge.net/Schematics/Frigidaire/IJ8JJV5P.gif

Water Inlet Valve

52 Reviews
Your Price
$55.39

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS7784018

Manufacturer Part Number 242252702

Manufactured by Frigidaire

The water inlet valve releases water from the supply line when activated, and sends it through to the water dispenser and ice maker in your refrigerator. To make this repair you will need an adjustable wrench, a quarter inch nut driver, and a sharp utility knife. Before you begin this repair make sure to disconnect the power supply to your refrigerator, as well as disconnect the inlet water supply from the back of the refrigerator. Note that this part may appear different than the original, but is an authorized manufacturer replacement.

This part works with the following brands: Frigidaire, Kenmore, Electrolux, Crosley, Westinghouse, Gibson

This part works with the following products: Refrigerator

This part fixes the following symptoms: Leaking | Ice maker not making ice | Not dispensing water | Ice maker won’t dispense ice

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

Was having problems with a faulty water valve so I replaced it but now it seems to dispense water every half hour or so without anyone hitting the dispenser. I know if water is leaking out of the icemaker assembly that usually means a faulty water valve but how about out of the water dispenser itself?

Kory
July 20, 2017
Answer:

Hi Kory, it sounds like you need to replace the diode kit, you can find that here 5303918287. I hope this helps.

28 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

My valve is malfunctioning and needs to be replaced. If I order this part, do I need any extra attachments or are there additional parts I should order, or is this it?

Van
July 20, 2017
Answer:

Hello Van, no, additional parts are not needed for this repair. Make sure when installing the new valve that the lines are cut flat. Best of luck with this repair!

8 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Ice maker works but no water out of front. Took apart and actuator is clicking against the electronic part like its supposed to. How can i be sure the issue is the inlet valve before i spend $50 on it?

Brian for model number FFHS2312NS3
April 17, 2018
Answer:

Hi Brian, Thank you for your question. To verify if the water inlet valve is causing the issue, you will need to test it with a multimeter. Before you begin to test your icemaker's water inlet valve, make sure you disconnect the appliance's power supply. The easiest way to do this is to unplug the unit from the wall. Alternatively, you could trip the appropriate switch in the circuit breaker panel, or you could remove the appropriate fuse from your home's fuse box. Consult with an appliance repair technician if you do not feel you have the skill or the ability to successfully complete this test. Locate your icemaker's water inlet valve, it is typically located behind a refrigerator. Gently pull your refrigerator away from the wall. You may want to place scraps of carpet, of some other soft material below the fridge to prevent damage to the floor. Turn of the water valve's water supply by closing the shut-off valve in the waterline leading to the water valve. Remove the lower access panel on the back of the refrigerator using a screwdriver or a nut driver. Place a container under the valve to catch any water that may spill from the water valve and its fill tube. Remove the water valve's fill tubing. Loosen the flare nut on the brass fitting that is found on the inlet side of the water valve. You can use a wrench to loosen the flare nut. Your water inlet valve is held in place on your refrigerator by means of a metal bracket. Use a screwdriver or a nutdriver to remove the screw that holds the water valve's bracket to the refrigerator cabinet. Gently pull the water valve out of the cabinet, and remove the tube from the outlet port. There are two wires connecting to the terminals of your water inlet valve. If yours is a double solenoid water valve, it will have four wires. Be sure to label each wire so that you know where to reconnect them later. Firmly grasp the metal connector of the wires in order to remove the wires. You may need to use a pair of needle-nosed pliers. Do not pull on the wires themselves. Set your multitester to the R X 1 ohms setting to test for continuity. Place each of the multitester's leads on a terminal. Your multitester should display a reading between 200 and 500 ohms. Closely examine your water inlet valve. The exact ohm resistance rating you should test for may be marked on the valve. If the test you conduct with your icemaker water inlet valve does not produce these results, then you should replace the component. I hope this helps. Thank you and have a great day!

8 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Icemaker assembly is leaking out water. Is that from the icemaker or the water valve not shutting?

Malaya
July 20, 2017
Answer:

Hi Malaya, it does sound like the valve is not shutting off fast enough. We recommend first checking the gear on the icemaker. If it is good then the valve is the problem. Please let us know if you have any further questions.  

5 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

How to test ice water valve or verified ice water valve if its good. Thanks

Jacques for model number FRS6R5ESBB
October 10, 2017
Answer:

Hi Jacques, Thank you for your question. You can test the solenoids on your valve with a multi meter. When testing your part, your solenoids should read any where between 500 and 1500 ohms of resistance. If it does not, or if your meter numbers do not shift at all, then you will need to replace your part. Good luck with your repair.

5 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Won't dispense water into icemaker. Checked the inlet valve and its pulling about 200 ohms. Also ice maker won't dump ice into the bucket. It seemed to be frozen so i thawed it out and put water in it. Still won't dump ice.

Ernie for model number FRS6LR5EW6
February 19, 2018
Answer:

Hello Ernie, thank you for your question. It sounds like the water valve is not functioning properly. When testing the valve, your solenoids should read any where between 500 and 1500 ohms of resistance. If it does not, or if your meter numbers do not shift at all, then you will need to replace your Valve. I hope this helps!

3 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Water very slow

Laura for model number FGUS2642LF1
December 7, 2017
Answer:

Hi Laura, Thank you for the question. The slow water flow could be two things. I would first check the water filter. If it has not been changed in the last 6 months it can cause a blockage and slow water. If the filter is good the water inlet valve will need to be replaced. Hope this helps!

Related Parts: Puresource Water Filter
2 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

The freezer part is leaking water into the bottom of my freezer then leaking out the door when the ice starts building up at bottom. I have tried to find the leak and can not see where its coming from. There is ice build up close to the fan. Ice build up in the drain area as well. Not sure if leaking from above or where. I have even turned water supply off and it still leaks. I have to bust the ice at the bottom with a hammer about every 3 -4 days

Rhonda for model number FRS6LF7JS0
November 28, 2017
Answer:

Hi Rhonda, Thank you for the question. This sounds like an issue with the defrost settings. I suggest testing the Defrost Thermostat Kit.The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Hope this helps!

2 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Dispenses water slowly with a loud humming noise from back of fridge only when trying to get water. Could this be the water valve?

Michael for model number FRS26R4CB3
January 17, 2018
Answer:

Hello Michael, Thank you for your inquiry. It does sound like it, but I would also check the water filter and lines to make sure they are not clogged. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

I have water leaking inside the freezer and running down the freezer walls.I purchased the ice container and it seemed to fix it for awhile and I had to defrost the freezer walls before I installed the ice container so what could be causing the water running down the freezer walls?

Joyce for model number FRS26RLECS2
December 28, 2017
Answer:

Hi Joyce, Thank you for the question. This can be caused be a few things unfortunately. I suggest turning the water supply off to the appliance for a few days to see if the leaking stops. If you still have the leaking down the wall you know there is a defrosting issues with the appliance. If it stops you can turn the part back on and try to keep an eye on the water level in the ice maker to see if it is over filling. You can also water the filter to see if it is not leaking. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

My icemaker is not working. There is no water in the ice tray maker. I installed a new valve on the back lower area of the fridge. The water dispenser still works on front of the fridge but after 24 hours, no ice or water is coming in to fill the ice maker tray. What next?

Kevin for model number FGUS2642LF2
December 31, 2017
Answer:

Hello Kevin, Thanks for your question. Check if the water filter is clogged and replace it if needed (it should be changed every 6 months generally). Have a look at the water lines to the icemaker too to see if they are clogged or frozen over. Lastly, make sure the condenser fan motor is working properly - it can be tested with a multi-meter to ensure continuity. I hope this helps.

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Hola. Tengo este refri. Que no me dispensa ni agua ni hielo. Hay agua en la línea y tiene filtro nuevo. No se que hacer ya. Si me pudieran ayudar. Gracias.

Rafael for model number DFHS2313MF2
January 2, 2018
Answer:

Hola Rafael, gracias por tu consulta. Verificaría la válvula de entrada de agua, el control del dispensador y me aseguraré de que las líneas no estén agrietadas ni tengan fugas. Puede probar la válvula y el control con un multímetro. Si no está familiarizado con el funcionamiento de un multímetro, hay videos de YouTube disponibles para ayudarlo. ¡Espero que esto ayude!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Replaced water valve, no ice. Replaced icemaker and after 24 hrs produced a few ice cubes.Checked water supply handle not fully open and corrected. Waited a day but now get no ice. Water dispenser ok. Did weak water supply damaged something?

Jesse for model number HSS25GFTGBB
October 26, 2017
Answer:

Hi Jesse, Thank you for the question.It may have shorted out the solenoids on the valve and the water inlet valve assembly may need to be replaced.Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

How do I stop leak from water valve push in connectors?

John
November 22, 2017
Answer:

Hi John, Thank you for the question. If the valve is leaking where the tubes connect you may need to check the tubes to see if they are split,wore out or just came lose.Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

The electrical connector seems to go on either way, does it matter?

Rick for model number FGUN2642LF1
September 7, 2017
Answer:

Hi Rick, Thank you for your inquiry. Yes it does matter where you plug your wires into the part. You should have three colored connectors on your fridge. Brown, yellow, and grey. The yellow goes on the yellow solenoid, the brown on the brown solenoid, and the grey goes on your green solenoid. Good luck with your repair.

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

When using the water or the ice dispenser the dispenser will not stop when the dispenser lever is released... to get the dispenser to stop i have to repeatedly tap the dispenser lever. i welcome your suggestion on where i should start in trouble-shooting this issue.

Kevin for model number FGHC2345LF
November 2, 2017
Answer:

Hi Kevin, Thank you for your question. You may have to look into your module dispenser being bad, or the dispenser control board just behind your buttons there. It sounds like it could be either of those two parts that are the issue for you. Good luck with your repair.

Related Parts: Ice Dispenser Module
1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

By "leaking" does that mean icicles forming on the ice maker?

Bruce for model number PLHS267ZDB4
August 23, 2017
Answer:

Hello Bruce, thank you for contacting us. If you are getting icicles forming off the ice maker it could be either the water valve or the solenoid in the ice maker. The water valve will feed the ice maker, but the ice maker has its own solenoid to control the water flow to prevent it from overflowing. if water was slowly getting through when it was suppose to be closed its possible that ice could drip forming icicles off the ice maker. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Replaced ice maker and water valve..still no ice

RUTH
August 9, 2017
Answer:

Hi Ruth, Thank you for your inquiry. If you have just replaced your water inlet valve and your ice maker is not making ice, you may have to wait 24 hours before the ice maker starts making ice again. Also make certain that the arm on the ice maker is in the correct position as that may also prevent the ice from being made. I hope this helps. Thank you and have a great day!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Water dispenser works,not making ice though

Jeff for model number Fghc2331pfaa
April 23, 2018
Answer:

Hello Jeff, thank you for your question. If the icemaker is not getting water from the valve to the icemaker so that it can freeze, dump and repeat the ice making cycle, the first part you will want to test/replace is the water valve. Here is a link that will take you to some testing information for the valve, and icemaker itself. https://www.partselect.com/Repair/Refrigerator/Not-Making-Ice/. I hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

The refrigerator stopped dispensing water while the ice maker continued making ice. I changed the filter and found out that it was hard to remove the holder for it appear to be under pressure (needed two hands.) the micro switch tested ok. I disconnected the line at the base of the freezer door, pressed the level and water came out. What can be causing this problem. Thanks for your help in advance.

Manuel for model number FRS3R5EMBC
January 29, 2018
Answer:

Hello Manuel, Thank you for your inquiry. You can test the water inlet valve with a multimeter. I would also check the tubes to make sure none of them are clogged or leaking. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Icemaker not making ice. Appears no water coming into the tray i replaced the water inlet valve and water filter and checked Green hose still no water strong water output from water dispenser though. Icemaker appears to be working. Gears in front turning and humming sound. What's my next step??

Tim for model number FRS26R4A
February 4, 2018
Answer:

Hello Tim, Thank you for your inquiry. You may have an issue with the ice maker control. Most heat release ice makers will have a removable cover at the front. Behind the cover is a series of electrical test points that can be used to diagnose the ice maker. The unit can be manually operated by inserting an insulated jumper wire into test points “T” and “H” to initiate a “test harvest”. The jumper should be insulated 14 gauge solid wire that has the insulation stripped back about 3/4 of an inch on both ends, and bent into a “U” shape. When inserted into the test points for 5 to 10 seconds, the motor should start and the cycle will continue on its own. You may have to manually close the freezer door switch for this to operate. This test will simulate a real harvest cycle and will operate the ejector blades, shut off arm and the fill valve in the proper sequence, and will allow you to do a proper diagnosis. This is a live voltage test and should only be performed by a qualified person. If the motor does not start, you can verify that you have power to the ice maker at test points “L” and “N”. If the ice maker is getting power and does not perform a cycle, then the module will need to be replaced. Test the white fill tube going into the ice maker as well, it may be clogged or cracked. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Ice maker not making ice, however water dispenser dispenses water. Is the water inlet valve the problem?

Tim for model number FFHS2322MBKA
February 5, 2018
Answer:

Hi Tim, Thank you for your question. It could be. Your water inlet valve has two solenoids, one for your ice maker and one for your water inlet valve. Even when your water solenoid is working your ice maker solenoid may not be. I could suggest testing it with a multi meter to be sure. If your valve is fine, it may be your ice maker that is the issue. I hope that helps. Good luck with your repair.

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Ice maker stopped making ice put new filter in 2day a ago made a hand full of ice then stopped could it be the water valuv

Roy for model number FFSSW61TQP6A
February 15, 2018
Answer:

Hello Roy, thank you for your question. Yes, the issue could be the water valve, or the icemaker itself. I would recommend removing the filter, and reinstalling it, just to see if that fixes the issue. If not, I would recommend replacing the valve. You can test the valve, before ordering if you are able. Here is a link that will take you to the testing information for the valve. https://www.partselect.com/Refrigerator+test-water-valve+repair.htm I hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Just about every other morning there is a puddle of water on the floor in front of the right (freezer door) side of my appliance. Any advice? Thank you

Michael for model number FGHS2344KF4
February 28, 2018
Answer:

Hi Michael, Thank you for the question. You can check the water filter first to make sure it is not backed up and needs to be replaced. You can also check to see if the ice maker is overfilling. Check all the water lines for leaks or holes. You can check the drain tube at the bottom of the freezer that leads to the drain pan. Make sure the drain pan dose not have cracks or needs to be cleaned out. You can also check to make sure the water valve at the back of the appliance to ensure it is not leaking. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

How long does it take to make ice after replacing a the water valve ?

Joe
March 3, 2018
Answer:

Hello Joe, Thank you for your inquiry. It can take up to 24 hours to make ice after replacing the valve, as long as you are getting a steady flow of water to the ice maker. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Replaced water valve yesterday it’s been 24 hours now late last night it started to make ice but today it not making ice but maybe every 4 or 5 hours is there anything i need to look at or is it normal occurrence. thank you

Joe
March 4, 2018
Answer:

Hello Joe, Thank you for your inquiry. It usually takes 24 hours to start making ice. On average, the ice maker should go through a cycle every 2 hours. If it's only making ice every 4 or 5 hours, I would check the water line to see if it has air in it or the line is not cracked, clogged or frozen. Also check the water pressure coming through the water line-it should be between 20-40 psi. Check the filter as well. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Hi, i've connected the new valve pt# 242252702 and the connectors get very hot and water starts to pour out of the icemaker. I took photos of the connections before i started the job so i know all the connections are right. "any ideas"

mike marsonek for model number PLRS267ZA
March 21, 2018
Answer:

Hello Mike, thank you for your question. First check the valve to be sure it is not a defective part. To test this, disconnect the water supply line connected to the valve, and disconnect the wires from the terminals. The number of coils will differ by model, and each coil will have two terminals. Set the multimeter to the lowest Ohms setting, and make sure the meter is calibrated properly. Place one probe on either terminal on the same solenoid. Do this for each solenoid coil. If the meter measures infinite Ohms of resistance– the display on a digital meter does not change much or the needle on an analog meter does not move– the valve has no continuity and is bad. If it is tested and is working properly If the water is constantly sending water to the icemaker, the issue could be with the icemaker itself. The icemaker has a motor module, which is like a timer. It sends for water, fills, freezes, dumps, repeats. If the icemaker is stuck in "fill" position that would keep the water valve open and constantly send water to the unit. I would recommend testing the icemaker itself since the valve has already been replaced. Most heat release ice makers will have a removable cover at the front. Behind the cover is a series of electrical test points that can be used to diagnose the ice maker. The unit can be manually operated by inserting an insulated jumper wire into test points “T” and “H” to initiate a “test harvest”. The jumper should be insulated 14 gauge solid wire that has the insulation stripped back about 3/4 of an inch on both ends, and bent into a “U” shape. When inserted into the test points for 5 to 10 seconds, the motor should start and the cycle will continue on its own. You may have to manually close the freezer door switch for this to operate. This test will simulate a real harvest cycle and will operate the ejector blades, shut off arm and the fill valve in the proper sequence, and will allow you to do a proper diagnosis. This is a live voltage test and should only be performed if you feel comfortable with the steps and working with live voltage. If the motor does not start, you can verify that you have power to the ice maker at test points “L” and “N”. If the ice maker is getting power and does not perform a cycle or immediately brings water to the unit and doesn't stop, then the icemaker will need to be replaced. I hope this information helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

I do not want to buy this valve if it is not the problem. Mechanically, the ice maker is running. The water tray is not filling up. The water at the door runs fine. The water filter was changed recently, so I do not think that is the problem. How can the door water run fine and the ice tray not fill? Is this a two section valve? One for water and one for ice? Two separate valves and solenoids in one part? Do I have the right part from my troubleshooting?

Robert for model number FFHS2611LBK
April 1, 2018
Answer:

Hello Robert, Thanks for your question. Typically this is due to a solenoid problem with the water inlet valve. You may want to test it with a multimeter for electrical continuity and replace it if it shows no continuity. Consider testing the icemaker as well to see if it is working properly. I hope this helps.

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

My water supply works, but when I moved my refrigerator, quit making ice

Gerald for model number 25357382601
April 9, 2018
Answer:

Hi Gerald, Thank you for the question. It sounds like something may have come lose when the appliance was moved. I suggest checking the wire connectors on the valve and the water supply tubes. Make sure they are connected and secure. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Ice maker almost constantly makes a surging, pulsing sound, like something is trying to start, but not making the full cycle. It was a bit better right after changing the water filter, but it still making the sound. Have cleaned all of the coils, etc. I dumped out all of the ice, and the ice maker is making ice. The water dispenser is fine.

Patrice for model number FRS26H7CSB2
May 2, 2018
Answer:

Hello Patrice, thank you for your question. I would recommend testing the valve. It almost sounds like the water valve is having issues opening on the icemaker port side. I would also recommend bleeding any air out of the water lines. I hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Leaking where the water line runs into the fridge. What part do i most likely need?

Jimmy for model number FRS6LR5EB6
9 days ago
Answer:

Hi Jimmy, thank you for your question. If the leak is coming from the part that the water line connects to, that would be your water inlet valve and would likely have to be replaced. I hope that helps. Good luck with your repair.

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

I repaced water intel valve & still not getting water up to the icemaker

jd for model number frs26h7csb4
December 5, 2017
Answer:

Hello JD, Thank you for your inquiry. I would check your water tubing, parts 241796405 and 218976409 to make sure it is not clogged or leaking. I would also check your water pressure as the valve requires at least 20 psi to function properly. I would also try replacing the filter. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

I replace the water inlet valve and wasn't getting any water into the ice maker tray. After looking at videos and further reading was able to remove the blockage of ice between the tube leading to the ice tray. Water is now flowing but not enough to full the tray. A matter fact the valve energize for less that 7 second. What is the remedy for such a situation?

Colin
August 14, 2017
Answer:

Dear Colin, Thank you for your inquiry. Sometimes if the ice maker has been inactive for a period of time it may take up to 24 hours for it to start making ice again. If not enough water is getting to the ice maker from the water inlet valve I would recommend using a multimeter to check the continuity of both parts to see which one is causing the issue. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer

Most Recent

Question:

Ice maker just quit working. Maker had cubes in it and appeared ready to unload. Did not think this was water valve problem as cubes had formed. Cleaned maker and reinstalled. Nothing happening.

David
Yesterday
Answer:

Hello David, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!

Was this helpful?
Show Answer
Hide Answer
Question:

My ice maker is freezing water in the tray right below the water tube in the freezer. I am testing the water inlet valve and the main water solenoid read 404 ohms, the Green (ice maker) reads 239 240 ohms, and the white (water line which is not used) reads 399 400 ohms. Instead of buying a new water valve, can i use the white solenoid instead of the Green one which was where the ice line was pluged in?

Jason
August 9, 2018
Answer:

Hi Jason, Thank you for your question. I would advise replacing the water inlet valve. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

Replace water value still not making ice when push water dispenser it leaks at the bottom where the hose is in the value

Nate for model number FRS23LH5DS1
August 6, 2018
Answer:

Hi Nate, Thank you for your question. If your water inlet valve does not seem to be the issue, the only other part to check would be your ice maker assembly itself. I hope that helps. Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer
Question:

Replaces the water valve and filter. I get water to the water tap but still no ice. I checked the tube and it is fine. Any more suggestions

Matt for model number FRS6LR5EM2
August 2, 2018
Answer:

Hi Matt, Thank you for your question. If you have replaced those two parts then the problem unfortunately may lay in the ice maker itself. The ice maker may have to be replaced. I hope that helps. Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer
Question:

Replaced the valve but ice maker still doesn't make ice.

Matt for model number FRS6LR5EM2
August 2, 2018
Answer:

Hello Matt, Thank you for the question. If the ice maker is not filling after the valve has been replaced, you may need a new Ice Maker, Part Number: PS735469. You can also check to see if the filter needs to be replaced. They should be changed every 6 months. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

Water dispenser does not dispense water and no water to the ice maker. I disconnected the water line at the coupler from under the freezer door. Closed the door and tried to get water from the dispenser. I can hear the actuator clicking and humming sound. At the same time, i see water coming out from the disconnected coupler. Do i have a bad water inlet valve or the line is frozen inside the freezer door liner? Greatly appreciated for your advise.

Chris for model number FRS3HR35KW0
April 27, 2018
Answer:

Hi Chris, Thank you for your question. It sounds like you have a bad water inlet valve. You would just have to inspect your lines to see if they are frozen or not. I would suggest doing that inspection and if you see that your lines are fine and water flows through no problem, then it would be your water inlet valve that you would move on to. I hope that helps. Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer
Question:

I need a water inlet valve, but I don't have the part number, will anyone fit?

Norma for model number PHSC39EGSS0
April 25, 2018
Answer:

Hello Norma, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is PartSelect Number: PS7784018. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

I have a small amount of water leaking from back of fridge underneath (freezer side) about 2x daily, it seems to come near the water valve area, the back wheel is always wet, when pulling fridge out) but cannot locate a drip when examining. Trying to confirm i need to replace the water inlet valve. Thank you!

Autumn for model number FRS6HR35KBO
April 23, 2018
Answer:

Hello Autumn, thank you for your question. There is a very good chance that the valve is where the water is coming from. The only other things I would suggest checking before you order the valve, is the water lines going from the valve, as they can get little pin holes and drip down the unit and puddle around the underneath of the fridge. Also, check the drain tube that runs from the underside of the fridge, and down into the evaporator pan. The water could be coming from there as well! I hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

I have very slow dispenser flow. If i replace the filter it will flow alright, still slow but in about 6 weeks it slows down again. We have sediment filter ahead of it and the refrigerator filter seems ok, but the flow is pathetic.Is it possible it's a valve issue? Been this way since installation, which i might add they had nothing but trouble with.I replaced the whole line to 1/4"plastic and have excellent flow with no valve.Thoughts or ideas?Thanks!Tsm

Tim
April 20, 2018
Answer:

Hello, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the appliance. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!

Was this helpful?
Show Answer
Hide Answer
Question:

I have copper tinted water (looks like a whiskey water drink) coming out of the water dispenser. Replaced water filter, didn't help. Rest of water in the house is clear. What would cause this?

Anne for model number PLH67EGSB4
April 18, 2018
Answer:

Hi Anne, Thank you for your question. If you did not flush the water filter before use, the water can be discolored. It is recommended that you flush 3-4 gallons of water through the filter before use. Check your owner's manual for specific instructions on how to flush the filter. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

Had ice on back of refrig wall (outside) no water or ice being made. Replaced water valve. Water begins to go up the peach colored valve to the filter and then comes back. We replaced the filter also

Sandy for model number FGHB2844LF7
April 10, 2018
Answer:

Hi Sandy, Thank you for the question. If there was ice build up the water line may also be frozen. I suggest testing the defrost thermostat, PartSelect Number: PS2378768.The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

I didn’t take a picture of which valve goes back to which value is there a way to know which hose goes to what?

Randy for model number 240531101
February 21, 2018
Answer:

Hi Randy, Thank you for your question. We do have an installation video that should help you out with that Randy. Here is the link: https://youtu.be/7nmDM3LZo8E . Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer
Question:

After replacing the valve, will you then have ice and water

Vicki
January 31, 2018
Answer:

Hello Vicki, Thank you for your inquiry. If your valve was not working, replacing it should fix your issue. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

I need a icemaker valve assembly. The ones I found have snapped. On the one I have had lines going in with a screw-in nut on the lines. Can you help me find the right part for it?

Billy for model number FRS6LR5EM8
January 27, 2018
Answer:

Hello Billy, Thanks for your question. The part number PS7784018 has the solenoids for the icemaker. I hope this helps.

Was this helpful?
Show Answer
Hide Answer
Question:

Hi -- my icemaker is working, but water dispenser is not. When i run the water dispenser, i can hear the water valve working, but it almost sounds like it is stopping at the point of the water dispenser. When doing this, the water filter fills up with water but never gets to the dispenser. I've replaced water filter, and likely that is not the problem since ice maker works fine. I opened up back of fridge, and ran water dispenser and could feel the line from the valve to dispenser moving. I also checked the line at the bottom front of the fridge that goes from the valve to the dispenser but it's hard to tell if anything could be blocking it. I'm ready to buy and replace the inlet valve, but wondering if there is something else that i am missing and that may not be the problem. Thanks!

Babak for model number FGHC2345LF3
January 14, 2018
Answer:

Hello Babak, Thank you for your inquiry. If you've already replaced the filter, I would check the inlet valve and water tube. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

Why doesnt my ice maker a fridigare make ice any more-please help,,thank you

Wayne
January 12, 2018
Answer:

Hi Wayne, Thank you for your question. If your ice maker is not making any ice, there are some parts that you will need to check to see which one is causing the issue. You will need to check the water fill tubes, the water inlet valve, the water filter and the ice maker. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

My ice maker is not getting water, but i have water at the door dispinser. What could the problem be? Is it the ice maker inlet valve?

Robert for model number fr56hr45kso
December 20, 2017
Answer:

Hi Robert, Thank you for your question. If the ice maker is not making ice and the ice maker is not getting water, then you will need to check the water inlet valve and the water filter. I would also check the water lines as well to see there are any leaks or blockages I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

Refrigerator in staff lunch room makes ice overnight but during the day it seems not to make ice at all?

Mike for model number FRS3HR5HW1
December 18, 2017
Answer:

Hello Mike, Thanks for your question. This problem commonly arises from the water inlet valve. Try testing it with a multi-meter and replacing it if it shows no continuity. Also replace the water filter if it has been 6 months since the last filter change. If those do not work, consider replacing the icemaker itself. I hope this helps.

Was this helpful?
Show Answer
Hide Answer
Question:

When I use the water dispenser water begins to leak from the somewhere around the water filter housing. I checked the filter and it seemed to be seated properly and I made sure the cover was screwed on hand tight. Still leaks so is this a filter issue or something else? Another issue as of late the refrigerator compartment will freeze so a thought was when it froze maybe a water line broke. Its a 16 yr refrigerator and I really don't want to replace it at this time but i would like to get this water leaking issue taken care of if possible.

Kevin for model number FRS23R4AW6
December 15, 2017
Answer:

Hi Kevin, Thank you for the question. It might be a damaged water line or the filter cup and housing. You may need to take it apart to check for damage or to see if a line is loose to these parts to confirm this is where the leak is coming from.Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

The water valve you have available has different connections for all the plastic water lines. All of my lines have male/female connections that have a threaded plastic nut to tighten. Is this type of water value still available?

Chris for model number frs23lh5ds9
December 5, 2017
Answer:

Hi Chris, Thank you for the great question. The manufacture no longer makes the valve with the threaded connectors. The new valve is a quick connect. You will need to cut the end off the tubing you have and make sure it is cut flat and just push it into the compression fitting on the new valve. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

Out of the blue one day the water stop dispensing water , only makes a humming noise. The ice tray is full so i am not sure what the problem is?

christopher for model number FRS6HR35KW1
November 22, 2017
Answer:

Hi Christopher, Thank you for your inquiry. If the dispenser has stopped making water, there are some parts that you will need to check to see which one is causing the issue. You will need to check the water inlet valve, the water dispenser actuator, the water filter, the filter cup,the water filter housing and the micro switch. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

When the ice maker refills the ice cube tray, water leaks from the Green tube, down near where it enters the valve. I just ordered the solenoid valve from you, replaced it, and it is still leaking. Any idea what i should do next?

Noelle for model number PHSC39EGSS0
November 20, 2017
Answer:

Hi Noelle, Thank you for your question. I do not see a green tube in your parts list here. The only thing I could think of is that where your water fill tub connects to the water line there is a break or it has separated a bit. I would suggest looking at the parts up there at your ice maker. Make sure the fill tube is connected fully with the water line. If you still get the leaking, you may need to replace one or both of the parts. I hope that helps. Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer
Question:

Water and ice quit working due to clogged filter. Ordered and installed new filter. Water dispense works great now but never started making ice again. Cube tray not filling. Is there a reset of some sort or need to order a new valve?

Craig for model number FFHS2611PFCA
November 9, 2017
Answer:

Hi Craig, Thank you for your question. Where the filter was just changed, you may have air in the line preventing the ice maker form making ice. Try turning off the ice maker for 30 seconds to see if the it resets and starts to make ice. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

The water dispenser keeps freezing up. After heating it with a hair dryer it works until it freezes up again. Any ideas ?

Jim for model number FRS6LF7JB3
November 8, 2017
Answer:

Hi Jim, Thank you for your question. I would suggest checking your dispenser door seal and make sure that it is closing properly. It sounds like the cold from your freezer is getting in your dispenser area and freezing up your water dispenser. I hope that helps. Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer
Question:

Water line underneath freezer door little blue fiter that one hose pushes into the other is leaking cant find the part any help

Ken for model number Frslf7jmo
October 31, 2017
Answer:

Hi Ken, Thank you for your inquiry. It sounds like you are looking for the connector. The part number for the connector is PS1765304. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

My ice maker stopped making ice. I was wondering if a fuse had blown or something that allows the water to go into the ice maker? Suggestions?

Chris for model number FPHS2687KF4
October 11, 2017
Answer:

Hi Chris, Thank you for your inquiry. There are some parts that you will need to check to see which one is causing the issue. You will need to check the water inlet valve, the ice maker, the water filter, the dispenser crusher housing, the drive blade, the shut-off arm spring and the mirco switch. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

All of a sudden my water dispenser will no longer dispense water. Can you tell me if this is repairable and if so what part would i need?

Charles for model number EW26SS65GS0
October 2, 2017
Answer:

Hi Charles, Thank you for your inquiry. There are some parts that you will need to check to see which one is causing the issue. You will need to check the water inlet valve, the water filter base, the dispenser module, the water filter, the water tube and the defrost thermostat. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

Ice maker has stopped making ice. No water is filling the ice cube tray. I have checked the water supply line, it is functional. Water dispenser is working properly. I also replaced the water filter. All i can think now is the inlet valve (part # 242252702). Thoughts? If it is, how do you disconnect and re-connect the water lines from the old and to the new valve assembly? Thanks.

Keith for model number Frigidaire FFSS2614QS0
September 25, 2017
Answer:

Hi Keith, Thank you for your inquiry. If the ice maker is not making ice, the arm on the ice maker my not be in the correct position and that is something you may have to check. If this is not the issue you may have to check both the ice maker and the water inlet valve. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer
Question:

The water dispenser has started dripping when it is not in use. I am worried that the water is going to drip onto the floor and ruin my flooring. Can I repair this myself?

Anne for model number LGHB2867PF7A
September 13, 2017
Answer:

Hi Anne, Thank you for the question, when the dispenser is dripping it usually means the water valve is stuck open a bit and letting water through the water lines and creating the drip. The valve will need to be replaced. Our previous customers replacing the valve stated it was a easy repair, so you should be able to do the repair on your own! Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

My water dispenser will dispense water randomly. If i "bump" the dispenser flapper, it will stop. But then it will do it again after a short amount of time. Other times it will just sit there and drip slowly. Could this be an issue with the valve?

Gary for model number ffhs2312nso
September 11, 2017
Answer:

Hi Gary, Thank you for the question. It sounds like the water valve is stuck open enough to cause the leak. I suggest replacing the water Inlet Valve. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

My water won't dispense when you push on the dispenser. You can here it hum when activated. The ice maker makes ice an i have changed the filter.

Brian for model number FRS6HR5JMB1
September 6, 2017
Answer:

Hi Brian, Thank you for your inquiry. There could be a few parts that could cause this issue for you. I would suggest checking your water inlet valve. The valve has two solenoids on it, one for the water and one for the ice maker. It could be that your solenoid for the water has stopped working. You could also test the micro switch inside of your dispenser area to make sure that it is working right as well. I hope this helps. Good luck with your repair!

Was this helpful?
Show Answer
Hide Answer
Question:

Would this water inlet valve going bad create a clicking sound?

FRED KEITH for model number LGUS2642LE1
August 16, 2017
Answer:

Hello Fred, that is a great question. If you are hearing clicking sounds from the water inlet valve there could be a mechanical failure inside it and may need to be replaced. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

I changed water filter. I am getting water at the front of the fridge but nothing filling ice maker tray and so no ice. Any suggestions. Thanks

NEAL for model number lgus2642lpo
August 1, 2017
Answer:

Hello Neal, Thank you for the question. If the ice maker is not filling it sounds like the Water Inlet Valve would need to be replaced, Part number PS7784018. Other then the water valve you may have a defective ice maker. Hope this helps!

Was this helpful?
Show Answer
Hide Answer

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 63 reviews What's this?
1-15 of 63
504 of 577 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Wrench (Adjustable)
Customer:
Jose from Alexandria, VA
Water leaking out of refrigerator
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

287 of 331 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Customer:
David from New Bern, NC
Icemaker stopped making ice
Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

151 of 193 people found these instructions helpful
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Customer:
Cory from Lincoln, NE
Water dripping from through the door water outlet and ice maker doesn't make ice.
I had two problems, the first was that water was dripping from the through the door outlet and the second problem is that the ice maker wasn't making ice.

Replacing the water valve was a simple process:

1. Turn off the water to the fridge at the household shutoff valve.
2. Move the fridge away from the wall.
3. Unplug the mains power (AC) plug from the wall power outlet.
4. Remove the 5 screws with a nut driver that hold the cardboard backing off the refrigerator.
5. (This is a great time to vacuum off the coils and underside of the fridge.) Disconnect the water supply from household plumbing with a box end wrench or channel lock pliers. I kept a large plastic cup and rag handy for the left over water in these hoses.
6. Remove the two screws from the water valve bracket on the right hand side and pull the water valve straight back from the fridge and line up the new valve in the same orientation.
7. Remove all the color coded electrical connectors (3 of them) and attach them to the new water valve.
8. Remove the remaining water hoses and attach them to the corresponding connectors on the new valve.
9. Dispose of the old valve and reinstall the new valve in reverse order.

The problem with the ice maker not making ice was because water was flowing so slowly from the valve that it was stopping in the fill tube at the back of the freezer and freezing stopping all water flow into the ice maker. I pulled the fill tube out of the back of the freezer from behind by rotating it 45 degrees counter clockwise and pulling straight out removing the ice blockage and drying the fill tube before I reinstalled.

Since I replaced the valve I had to take the cover off of the icemaker and set the water fill level down (screw toward the minus sign) and then adjusted it by checking the ice after each time it dropped and increasing the fill amount by 1 full turn (roughly 0.7 ounces) until it was just enough to make fully formed ice cubes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

76 of 96 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set, Wrench set
Customer:
hubert from winchester, VA
No water to ice maker or water dispenser
pulled fridge from wall, removed card board cover, unplug the fridge. turn the water off to the fridge. remove the water source from fridge first then remove 2 screws that hold the valve. then the wire plugs. hoses.. they were color coded.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

57 of 71 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
Patrick from Georgetown, KY
Water valve had broken
Repair was very easy - and to my great delight, they have replaced the old-style compression fittings with PEX push-fittings. You just clip the old compression ring and nut off the tubing and insert the tubing firmly into the fitting. SNAP! VOILA! PEX fittings are the greatest things since sliced bread. I used it to plumb my new house.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

44 of 51 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
Warren from Ottumwa, IA
Ice maker quit making ice
turned off water supply at water line to fridge. removed two hex head screws @ bottom of rear of appliance that hold the water valve in place.
Simply moved color coded elect. plugs from old one to new one, same with water lines. Only difference is, the replacement one I got uses push in water lines and my original was compression fit. No problem though, just cut the nipple off of original line going into new valve and you are good to go. Might want to have an extra 1/'4" brass compression washer though for the one remaining line. Whole process I did on my lunch break at home less than 30 minutes.
Only problem though was nothing changed. Spoke with service man over the phone and he said MOST of the time it is water freezing up in the inlet tube top of machine, inside. Remove water line from rear outside on top behind freezer and with a straw try to blow through, if it is froze it will not go through. Mine did not go through. Used hair dryer inside freezer in back on incoming line 5-10 minutes,thawed out, makes ice. Go figure. Changing valves was easy and well described as stated, just not necessary in my case, but now I know. Thanks, Warren in Iowa

Help other customers find the most helpful instructions.

Were these instructions helpful?   

39 of 44 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)
Customer:
Terrance from Orland Park, IL
Ice maker cycling properly but not getting water on fill cycle
1.Unplugged appliance. Removed rear access panel, turned off water supply valve, removed two screws holding water valve assembly in place.
2. Removed and drained all water lines.
3. Removed three electric solenoid wiring connections.
4.Cut and marked all water lines to facilitate new connecting procedure (instructions provided with the new valve assembly).
5. Inserted the water lines into the new valve by applying a bit of vaseline on tubing end prior to pushing lines into O-ring fittings.
6. Clean the embarassing dust from under the appliance!!!

Note: All lines, wiring, and valves were color-coded to prevent connecting to wrong lines and electric solenoids.

Note: Be sure to remove water inlet supply trough to rear of ice-maker. This tube may freeze solid and prevent water from filling freeze tray. This is done by turning the inlet pipe on the back of the cabinet 1/4 turn and retracting from cabinet.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

34 of 46 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
kyle from Palo Alto, CA
Water coming out of the ice maker when dispensing water from the door.
This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having.
The fix was easy just a few wires cut and spliced and viola fixed.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

22 of 24 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Customer:
william from new port richey, FL
Ice maker did not produce ice.
The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water valve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others.
Take care-Bill

Help other customers find the most helpful instructions.

Were these instructions helpful?   

24 of 32 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench set
Customer:
Russell from Jacksonville, AR
Water leak
Unplug turn water off
Removed two screws with nut driver loosen one
Disconnected three solenoid valves
Disconnected four water lines
Plug tubing in, tighten one flare fitting
Reattach wires to solenoids
Slide under loose screw, replace two screws
Turn water on check for leaks plug in get a drink of water

Help other customers find the most helpful instructions.

Were these instructions helpful?   

23 of 30 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench set
Customer:
Linda from Belmont, OH
Water wasn't filling ice tray to make ice.
Unpluged the item. Turned off the water source. Removed the card board cover. Dis-connected the water hoses. Unpluged the connetors. Matched up the colores and put it back together, very easy. Everythings was color coded.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 22 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Customer:
Robert from Louisville, KY
Ice maker wasn't making ice
I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

15 of 17 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Customer:
Jim from Herington, KS
It was fast and easy, no to mention affordable.
Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

15 of 19 people found these instructions helpful
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Customer:
Deborah from Merced, CA
Water actuator had broke off and water leaked from dispenser
The hardest part was figuring out how the front plate comes off. The tray will come forward when pried with a screwdriver. Then the top will come off but you will have to leave on due to attached wires. After that it was a piece of cake. Unscrew screws (6), remove small plates holding arm in place, remove arm, replace with new actuator, and close things up. As far as the valve, just take your time and, if needed, cut off pointed ends of tubings and push into new valve. Unplug color coded plugs and plug into new valve. Reattach valve to fridge and your done. We started everything up before attaching backing to make sure there were no leaks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 17 people found these instructions helpful
Parts Used:
  • Water Inlet Valve
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Customer:
Paul from Anderson, IN
Drip from door water dispenser
The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 63
Customer Reviews
Average Rating:
52 Reviews
4.6
out of 5
Filter By Rating:
  • 5 Stars
    43
  • 4 Stars
    3
  • 3 Stars
    2
  • 2 Stars
    1
  • 1 Stars
    3
Sort by:
Sort by:

Model Cross Reference

This part works with the following models:

PartSelect Number: PS7784018
Manufacturer Part Number: 242252702
Brand
Model Number
Description
Kenmore
25344302400
Refrigerator
Kenmore
25344302401
Refrigerator
Kenmore
25344303400
Refrigerator
Kenmore
25344303401
Refrigerator
Kenmore
25344303402
Refrigerator
Kenmore
25344303403
Refrigerator
Kenmore
25344304400
Refrigerator
Kenmore
25344304401
Refrigerator
Kenmore
25344309400
Refrigerator
Kenmore
25344309401
Refrigerator
Kenmore
25344333600
Refrigerator
Kenmore
25344333601
Refrigerator
Kenmore
25344333602
Refrigerator
Kenmore
25344333603
Refrigerator
Kenmore
25344333604
Refrigerator
Kenmore
25344333605
Refrigerator
Kenmore
25344333606
Refrigerator
Kenmore
25344333607
Refrigerator
Kenmore
25344333608
Refrigerator
Kenmore
25344333609
Refrigerator
Kenmore
2534433360A
Refrigerator
Kenmore
25344352400
Refrigerator
Kenmore
25344352401
Refrigerator
Kenmore
25344352403
Refrigerator
Kenmore
25344352404
Refrigerator
Kenmore
25344352405
Refrigerator
Kenmore
25344352406
Refrigerator
Kenmore
25344352407
Refrigerator
Kenmore
25344352408
Refrigerator
Kenmore
25344352409
Refrigerator