755799-1-M-GE-WE01X10167 -Rotary Selector Knob
Part Location Diagram of WE01X10167 GE Rotary Selector Knob
See part 29 in the diagram
( Grid squares measure 1x1 inch )
755799-1-S-GE-WE01X10167 -Rotary Selector Knob 755799-2-S-GE-WE01X10167 -Rotary Selector Knob 755799-3-S-GE-WE01X10167 -Rotary Selector Knob Part Location Diagram of WE01X10167 GE Rotary Selector Knob
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Rotary Selector Knob WE01X10167

Rated by 3 customers 

Really Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

$ 65.77
  Special Order
Get FREE EconoShip on orders over $100! T&C apply
PartSelect Number PS755799
Manufacturer Part Number WE01X10167
Manufactured by GE
Product Description

Rotary Selector Knob Specifications

This knob accepts a D-shaped shaft.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Dryer.
This part works with the following products:
General Electric.
Part# WE01X10167 replaces these:
AP3419163, 948391, WE01X10084, WE1X10084
Back to Top
Customer Repair Stories
 Average Repair Rating: 3.8 / 5.0, 3 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Plastic knobs broken at the base.
I pushed the new knob into place and voila!
Other Parts Used:
Rotary Knob Timer Knob Rotary Selector Knob
  • Andre from Newport News, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken start switch
Screwdriver on right and left of the top to pry it off the top panel spring clips.
rotated the switch assembly by hand from the back to remove it from the front panel.
removed the connectors and connected them to the new switch.
Put the new switch in and rotated it to mount it to the front panel.

Thank you for your help. I ordered a switch and a knob for a GE dryer.

A neighbor had this washer and a dryer sitting in their driveway—getting rid of them because of a broken switch and knobs.

A repair man told them it would be $250.

My neighbor gave the washer and dryer to me for free and I gave them to a single Mom who was in need.

The repair took me 10 min and cost me less than $75 thanks to your web site help.

Here’s a tip for owners of a GE Profile washer and dryer—The plastic knobs are weak and split where they connect with the switch. Pull them off and wrap (6-8 times) the outside diameter of the connection part of the knob with electrical tape.
Do-it-yourself with partselect.com!

Pete Haas
Carlsbad CA
Read less
Other Parts Used:
Rotary Selector Knob Start Switch
  • Pete from Carlsbad, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace upper drum-glide & felt. Also replaced lower felt
Unplugged and raised the top of the dryer (This allows access to the screws that attach the front of the dryer to the body of the dryer). 2nd- removed the two screws inside the front and down approx 5 inches on each side of the front. Also remove the small plastic tie-wrap that holds the wiring to the top of the dryer. It will be on the right hand side if facing the front of the dryer. Unplug the two plastic wire plugs that attach the wiring to the controls. Use a flat screw driver to pry the front away from the body of the dryer (this will unattach clips that hold the front in place. Remove the felt guide. The factory glue will keep some of the felt attached to the housing. This is where I used the utility blade to remove the rest of the felt. Then I used the soft wire-wheel to remove the rest of the residue of the glue. Probably not necessary. I replaced the top felt first with the teflon guides on it. I used spring loaded clamps to hold it in place. The clamps were probably not necessary either because the glue holds very well. Next I replaced the lower felt. While the front of the dryer was removed this was a good time to use the nozzle on the sweeper to remove the lint that was built up inside of the dryer. Reverse your steps and put your dryer back in service. You may need to reach through the door to align the drum over the felt in order to re-attach the front of the dryer.
Read less
Other Parts Used:
Rotary Selector Knob Lower Felt Seal Top Drum Glide Kit
  • Jeffrey from Washington, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Be the first to ask our experts a question about this part!

Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS755799
Manufacturer Part Number: WE01X10167
Brand
Model Number
Description
General Electric
DCXH46EA3WW
Dryer
General Electric
DPXH46EA0WW
Dryer - Electric
General Electric
DPXH46EA1WW
Dryer - Electric
General Electric
DPXH46EA2WW
Dryer - Electric
General Electric
DPXH46EA3WW
Dryer - Electric
General Electric
DPXH46EF0WW
Dryer - Electric
General Electric
DPXH46GA0WW
Dryer - Gas
General Electric
DPXH46GA1WW
Dryer - Gas
General Electric
DPXH46GA3WW
Dryer - Gas
General Electric
DPXH46GA4WW
Dryer - Gas
General Electric
DPXH46GA5WW
Dryer - Gas
General Electric
DPXH46GA6WW
Dryer - Gas
General Electric
DPXH46GF0WW
Dryer - Gas
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Rotary Selector Knob
$ 65.77
  Special Order
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.