GE/GE_Thumb/00111364i01.gif
See part 29 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Rotary Selector Knob

$ 48.67   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS755799
Manufacturer Part Number WE01X10167
Manufactured by GE
Product Description

Rotary Selector Knob Specifications

This knob accepts a D-shaped shaft.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Dryer.
This part works with the following products:
General Electric.
Part# WE01X10167 replaces these:
AP3419163, 948391, WE01X10084, WE1X10084
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories
 Average Repair Rating: 3.8 / 5.0, 3 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    Replace upper drum-glide & felt. Also replaced lower felt
    Unplugged and raised the top of the dryer (This allows access to the screws that attach the front of the dryer to the body of the dryer). 2nd- removed the two screws inside the front and down approx 5 inches on each side of the front. Also remove the small plastic tie-wrap that holds the wiring to the top of the dryer. It will be on the right hand side if facing the front of the dryer. Unplug the two plastic wire plugs that attach the wiring to the controls. Use a flat screw driver to pry the front away from the body of the dryer (this will unattach clips that hold the front in place. Remove the felt guide. The factory glue will keep some of the felt attached to the housing. This is where I used the utility blade to remove the rest of the felt. Then I used the soft wire-wheel to remove the rest of the residue of the glue. Probably not necessary. I replaced the top felt first with the teflon guides on it. I used spring loaded clamps to hold it in place. The clamps were probably not necessary either because the glue holds very well. Next I replaced the lower felt. While the front of the dryer was removed this was a good time to use the nozzle on the sweeper to remove the lint that was built up inside of the dryer. Reverse your steps and put your dryer back in service. You may need to reach through the door to align the drum over the felt in order to re-attach the front of the dryer.
    • Jeffrey from Washington, PA
    • Difficulty Level:
      Easy
    • Total Repair Time:
      1- 2 hours
    • Tools:
      Screw drivers
    • Parts Used:
      WE01X10167, WE9X105, WE03X10001
    8 of 9 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Broken start switch
    Screwdriver on right and left of the top to pry it off the top panel spring clips.
    rotated the switch assembly by hand from the back to remove it from the front panel.
    removed the connectors and connected them to the new switch.
    Put the new switch in and rotated it to mount it to the front panel.

    Thank you for your help. I ordered a switch and a knob for a GE dryer.

    A neighbor had this washer and a dryer sitting in their driveway—getting rid of them because of a broken switch and knobs.

    A repair man told them it would be $250.

    My neighbor gave the washer and dryer to me for free and I gave them to a single Mom who was in need.

    The repair took me 10 min and cost me less than $75 thanks to your web site help.

    Here’s a tip for owners of a GE Profile washer and dryer—The plastic knobs are weak and split where they connect with the switch. Pull them off and wrap (6-8 times) the outside diameter of the connection part of the knob with electrical tape.
    Do-it-yourself with partselect.com!

    Pete Haas
    Carlsbad CA
    • Pete from Carlsbad, CA
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
      Pliers, Screw drivers
    • Parts Used:
      WE01X10167, WE04X10008
    7 of 8 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Plastic knobs broken at the base.
    I pushed the new knob into place and voila!
    • Andre from Newport News, VA
    • Difficulty Level:
      Really Easy
    • Total Repair Time:
      Less than 15 mins
    • Tools:
    1 of 3 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Related Parts
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS755799
      Manufacturer Part Number: WE01X10167
      Brand
      Model Number
      Description
      General Electric
      DCXH46EA3WW
      Dryer
      General Electric
      DPXH46EA0WW
      Dryer - Electric
      General Electric
      DPXH46EA1WW
      Dryer - Electric
      General Electric
      DPXH46EA2WW
      Dryer - Electric
      General Electric
      DPXH46EA3WW
      Dryer - Electric
      General Electric
      DPXH46EF0WW
      Dryer - Electric
      General Electric
      DPXH46GA0WW
      Dryer - Gas
      General Electric
      DPXH46GA1WW
      Dryer - Gas
      General Electric
      DPXH46GA3WW
      Dryer - Gas
      General Electric
      DPXH46GA4WW
      Dryer - Gas
      General Electric
      DPXH46GA5WW
      Dryer - Gas
      General Electric
      DPXH46GA6WW
      Dryer - Gas
      General Electric
      DPXH46GF0WW
      Dryer - Gas

      Get in touch, we're here to help!

      Open until 10PM EST

      Contact Customer Service