Install videos!
735645-1-M-Frigidaire-134144700 -Single Spring with Insulators
Part Location Diagram of 134144700 Frigidaire Single Spring with Insulators
See part 14 in the diagram
Replacing your Frigidaire Washer Single Spring with Insulators
735645-1-S-Frigidaire-134144700 -Single Spring with Insulators 360 view
( Grid squares measure 1x1 inch )
735645-1-S-Frigidaire-134144700 -Single Spring with Insulators 735645-2-S-Frigidaire-134144700 -Single Spring with Insulators 735645-1-S-Frigidaire-134144700 -Single Spring with Insulators 360 view
Part Location Diagram of 134144700 Frigidaire Single Spring with Insulators Replacing your Frigidaire Washer Single Spring with Insulators
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Single Spring with Insulators 134144700

 Fits your GWT445RGS1!
★★★★★
★★★★★
4 Reviews

Rated by 13 customers 

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

$ 47.65
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your GWT445RGS1!
PartSelect Number PS735645
Manufacturer Part Number 134144700
Manufactured by Frigidaire for Frigidaire, Kenmore, Gibson, Crosley
Product Description

Single Spring with Insulators Specifications

This is a single spring with insulator, but you may also know it as a suspension spring. It is a part for your washing machine. If your tub is no longer stable, which would cause shaking, moving, and excess noise, you may need to replace this part. The tools you will need in order to make this repair include a Phillips screwdriver and a pair of locking pliers. You will find the insulator on each end of this piece. We recommend replacing both springs in your appliance at the same time to ensure even wear.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Frigidaire Washer Single Spring with Insulators

Replacing your Frigidaire Washer Single Spring with Insulators
Back to Top
Troubleshooting
This part fixes the following symptoms:
Will not drain
This part works with the following products:
Washer, Washer Dryer Combo.
Part# 134144700 replaces these:
AP3212517, 936912, 131277700, 131663600, 134136300
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
5.0
Filter By Rating:
  • 5 Stars
    4
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Donald B - March 15, 2023
  Verified Purchase
Easy to replace
Appears to work fine
★★★★★
★★★★★
Dennis B - November 5, 2019
  Verified Purchase
Heavy drum repair
Videos made identify problem Easy. Part was great. Lifting washer drum to get spring in place was a challenge until I used a wire hanger and a handle with a ring from exercise equip. Worked like a charm
★★★★★
★★★★★
Donna D - July 28, 2018
  Verified Purchase
Helped me find the part I needed
I couldn't find my part using the diagram provided so called your service dept. They quickly found the part and got it on it's way. I am NOT telling my husband how I got the part in without his help.
★★★★★
★★★★★
Hector B - February 27, 2018
  Verified Purchase
Excelente sevicio
Very good service!!
  • 1
Back to Top
Customer Repair Stories
 Average Repair Rating: 3.0 / 5.0, 13 reviews. What's this?
Sort by:
  • 1
  • 2
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Spring broke and front loading washer made loud noise when it went into spin cycle.
Removed the back and lower panel in the front of machine. Turned it on its side to replace spring, not tools required. Then stood it up and replaced both shocks by removing plastic pins that hold them in place, no tools required. The only time you need tools is to remove the metal panels to get to the parts. Now it makes no noise and runs like a new washer. Paid $140 for the parts, a new machine would have cost over a thousand and would be one of those digital nightmares that don't last as long. This machine is 18 years old.
Read less
Other Parts Used:
Shock Absorber Kit Single Spring with Insulators
  • DONNA from VALPARAISO, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was bouncing and emitted a banging noise only when on high speed spin
I watched the videos and replaced the shocks and suspension springs. This worked to stop the unit bouncing completely and cut the banging noise in half. Further diagnosis revealed a damaged drum and outer shell. The repair itself was very simple and didn't require special tools or skills. There is a tricky shock absorber locking pin on the right shock bottom position. There is a control box of some sort that prevents the complete removal of the pin without breaking it. On install, I simply pushed the pin through from the front. Ultimately, I ended up replacing the unit. However, I found the site to be extremely helpful. Great service.
Read less
  • chris from COMMERCE TWP, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The only problem was that the drive belt was so tight that it was two inches short from the drive shaft making it very difficult to put on by hand.
I did my best to stretch the belt out and as I wrapped it around the pulley one hand was preventing the belt from slipping off and the other hand had the screwdriver to use as Leverage to stretch and slip the belt on the other side of the pulley. One thing that I saw but didn't try was to use zip ties to temporarily hold the belt in place so it didn't slip off that may have helped.
Read less
Other Parts Used:
Shock Absorber Kit Door Strike Single Spring with Insulators Drive Belt - 6 ribs
  • Bret from MILACA, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
right side tub mounting spring broke
disconnected electric and water supply. removed back cover from front loading washer. removed two screws from spring end plate on the top of the washer. replaced old spring with new spring/insulators by lifting the tub and hooking the new spring on. replaced the back cover and top spring cover plate. reconnected water supply and electric. machine is working like it did before the spring broke. very easy fix. the majority of the effort was moving the washer around to get easy access.
Read less
  • Lisa from Phoenix, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 shocks and one spring broke
repair wasn't too difficult, hardest was raising the drum to engage the springs.

Steps I took:

remove the rear and front (bottom) covers. To remove the rear cover, I went ahead and took the hoses off. The bottom cover needs a good tug once the two screws are removed.

Once both covers were off, it was obvious what had to be replaced.
Pushing the notch on the shocks, removed both top and bottom pieces. Then I used books to lift the drum so that i could attach the new springs. Removed the books, installed the shocks from the top to the bottom.

Went ahead and removed the coin drop, cleaned it out, and reattached. Ran the washer two cycles to confirm the vibrations were gone. Loaded it up with towels (seemed to cause the worst vibs) and it was quiet.

Re-installed the covers and that was it.
Read less
Other Parts Used:
Shock Absorber Kit Single Spring with Insulators
  • Don from campbell, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One spring was broken and the shaking broke the two shock absorbers
I disconnected the water and the power first. I then removed the back of the machine. I also removed the 8 screws that hold the top and slid it forward to release it from the clips. I tilted the to up withour removing any wires. I then put a 2X4 accross the top and used #14 electrical wire to lift the drum up so I could attach the spring. It was easy to remove nad replace the shock absorbers once the release was pressed down on each pin. I did have to remove two screws that held a control panel top the base of the machine on the left lower corner. (looking from the back of the machine) to make it easier to remove and install that shock absorber. That part of the install was a breeze. The parts were all correct and arrived quickly.
Read less
Other Parts Used:
Shock Absorber Kit Single Spring with Insulators
  • Berardo Jr. from North Billerica, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking and broken shock absorbers
Removed spring retainer straps from top of springs. Propped up tub with blocks and a wedge. Lifted out each spring and replaced. Re-attached spring retainer straps. Removed pins from shock absorbers (old/broken ones). These break due to moving washer w/out installing original foam blocks and support screws or due to age and fatigue. Pins have a retainer that must be depressed as you pull or push them out. may need to spin back and forth with pliers as you pull them. Bottom right pin won't come out w/out a hassle. Cut it in pieces with dykes and used spare pushed in from the FRONT (not the rear, as it was originally installed). Found leak was not fixed by getting the drum back up to proper height. Found bolt on tub had broken the bottom of the soap dispenser "tray". This is a 50.00 part. Made a patch from the bottom. Roughed up plastic and used silicone adhesive. After it had adhered filled from top with more silicone. Allowed 24 hrs to dry. Washer is as good as new.
Read less
Other Parts Used:
Shock Absorber Kit Single Spring with Insulators
  • Dan from Concord, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Out of balance when on final spin cycle
Had to replace one Spring on top of the tub and both shock absorbers. Anyone with even a limited amount of mechanical ability could handle this repair. Save yourself about $300 in repair cost and replace these items yourself. Spring and Shocks absorber kit cost less than $60 with shipping.

Just look at the diagram that comes with the parts, it's a piece of cake. The most difficult part is replacing the spring, she is stiff. You will need to take the top of the machine off, which is super easy, and remove the metal keeper on top of the frame rail. Get someone to help you as you will need to lift the tub and slip the spring over the frame rail.

The shocks are the easiest part of the repair, and should take less than five mins. to replace.
Read less
Other Parts Used:
Shock Absorber Kit Single Spring with Insulators
  • Kevin from Vancouver, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tub was sagging and seal was not complete, would leak
The tub is supported by two springs and two shock absorbers. First remove the back panel of the washer. Then I placed the auto jack from my car under the tub, alongside the motor, and cranked it up, lifting the tub, until the top of the seal in the front was compressed. Then I took the top off of the washer to access the springs. There are retaining straps over the top of each spring that I had to remove to get to the springs. Pulling up hard on the spring allowed me to get a pair of pliers on the spring and pull it out of the slot it was in.

Once it was out of the slot I could remove it from the tub as well. I put the new spring in and replaced the retaining strap. Then I repeated this process on the other spring.

Once both springs were in place the tub was hanging as it should and the seal around the door was smooth all the way around. I haven't seen any more leaks since replacing the springs.
Read less
Other Parts Used:
Door Strike Single Spring with Insulators
  • Steven from Irving, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring Ang Shock Broke
.
  • James from North Canton, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
Back to Top
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carol
May 9, 2019
Is there just one suspension sping on my washer or one on each side?
For model number FWT445GES2
PartSelect logo
Hello Carol, Thank you for the question. There are 1 spring on each side of the drum, so two required for the appliance. Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
  • 1
Back to Top
You May Also Need ?
Shock Absorber Kit
$39.64
  In Stock
Affresh Washing Machine Cleaner - 3 pack
$12.58
  In Stock
Affresh Dishwasher Cleaner Tablets - 6
$19.09
  In Stock
Produce Preserver Filter
$21.50
  In Stock
Affresh Cleaner
$19.09
  In Stock
Cooktop Cleaner
$17.74
  In Stock
Affresh Washing Machine Cleaner Tablets – 6 Count
$21.14
  In Stock
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS735645
Manufacturer Part Number: 134144700
Brand
Model Number
Description
Frigidaire
38712
Washer - WASHER
Frigidaire
38802
Washer - WASHER
Kenmore
41724182300
Washer
Kenmore
41724182301
Washer
Kenmore
41727182700
Washer
Kenmore
41727182701
Washer
Kenmore
41727182702
Washer
Kenmore
41727182703
Washer
Kenmore
41727182704
Washer
Kenmore
41729022890
Washer
Kenmore
41729042990
Washer
Kenmore
41729042991
Washer
Kenmore
41729042992
Washer
Kenmore
41729052990
Washer
Kenmore
41729052991
Washer
Frigidaire
41739012890
Washer - Stackable
Frigidaire
41739012891
Washer
Frigidaire
41739022890
Washer
Frigidaire
41739022891
Washer
Kenmore
41740032990
Washer
Kenmore
41740042990
Washer
Kenmore
41740052990
Washer
Kenmore
41740142000
Washer
Kenmore
41740412700
Washer
Kenmore
41740412701
Washer
Kenmore
41740412702
Washer
Kenmore
41740412703
Washer
Kenmore
41741042000
Washer
Kenmore
41741052000
Washer
Kenmore
41741142000
Washer
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service
Single Spring with Insulators
$ 47.65
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.