This turntable motor coupler connects the turntable motor to the turntable tray to activate the tray. If your tray does not consistently turn or does not turn at all, replace this part. This part measures 1 1/2" in diameter. Remember to unplug your microwave from the power source as a safety precaution. Refer to the openers manual provided by the manufacturer for further installation instructions and accurate guidance.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Tray won’t turn | Won’t turn on
This part works with the following products:
Microwave.
This part works with the following products:
General Electric, Kenmore, Hotpoint.
Part# WB06X10420 replaces these:
AP3416049, 942560, WB6X10420
Customer Reviews
Average Rating:
★★★★★
★★★★★
28 Reviews
4.8
Filter By Rating:
5 Stars
23
4 Stars
4
3 Stars
1
2 Stars
0
1 Star
0
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
James G - April 7, 2022
Verified Purchase
Correct part, easy repair.
The part was exactly what I needed and the repair was easy and quick. Turntable is now working again.
★★★★★
★★★★★
Daniel L - February 17, 2022
Verified Purchase
Coupler for microwave
After trying several other vendors, I found, ordered and received in a timely manner. Great experience.
★★★★★
★★★★★
Michael H - April 6, 2021
Verified Purchase
East repair, part snapped in. Works.
The reason I did not give you 5 stars is the shipping took way to long. The delivery left Calif and went thru Oregon up into Washington. There it was transferred to another truck and brought back to Oregon to be delivered. US mail would have been quicker and cheaper on my end.
★★★★★
★★★★★
Annette J - December 13, 2020
Verified Purchase
Easy repair Works great
My microwave turntable is working again. Part arrived quickly.
★★★★★
★★★★★
Bryan A - October 20, 2020
Verified Purchase
Right part
Easy to find and easy to install.
★★★★★
★★★★★
Dawn G - April 28, 2020
Verified Purchase
Exactly what I needed
Our turntable quit working. Found your website. Ordering was very easy. Product shipped fast
★★★★★
★★★★★
Ann B - April 21, 2020
Verified Purchase
Easy repair
Turntable Coupler. Was easy to replace. Part of the broken coupler had fallen into the microwave but it did not cause a problem. Two minute replacement.
★★★★★
★★★★★
John F - February 15, 2020
Verified Purchase
Turntable Coupler
Easy to install. Works great>
★★★★★
★★★★★
RAVI K - October 25, 2019
Verified Purchase
Easy to install. No sweat.
The part was in great condition and delivered promptly . It is up and running..
★★★★★
★★★★★
De B - October 19, 2019
Verified Purchase
Great service
Easy to use website and managed to find what I needed quick delivery was fast and parts fit fine
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 25 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Turn table stopped rotating.
I tried to install the new part several times, but it didn't work. So I used a pencil to move things around down the shaft. After that the new part went in and now my microwave is doing what I need it to do.
Michael from FISHERS, IN
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My turntable quit working
I replaced the turntable motor and coupler. It did not fix the problem. Not sure where to go from here. Looks like the next step involves parts that are as expensive as a new microwave.
Because the turntable coupler was broken, the turntable wouldn't rotate.
I simply removed the broken coupler and snapped the replacement part into place, being careful to line up the slot on the new coupler. Just a note: the troubleshooter guide on the website was a great help in determining how to fix the problem. The comment section let me know this a simple fix anyone could do.
Michael from SEVIERVILLE, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
turntable coupler broken
had someone else do it...he advised very easy to accomplish.
Judith from Clements, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace turntable coupler on microwave
Piece did not fit as well as old piece needed to take off a small piece to make it fit. Once it was in the turntable worked again
Patricia from Smithtown, NY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Coupler broke at shaft & motor seized
Removed 5 philip head screws from under panel. Under panel droped down exposing drive motor. Removed one drive motor screw, replaced with new motor at the same time lining up new coupler. Pressed together, reinstalled motor srew, attached wire coupling and tested. Worked fine. Reinstalled lower panel screws (5)and unit was ready to go. I
... Read moreordered two of each units because I believe this to be weak link in the unit. It was only 2 years old, used little as I have another home. I recently installed a like unit (Hanging) and it was a breez. 4 srews properly placed, electrical cord hole properly drilled & ready to go in 45 minutes.
Read less
Joseph from Columbia, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable coupler broken, and would not turn
When I received the part, I popped it in and POW, problem solved. I praise PartSelect, they offered my part at a fantastic price compared to other vendors and shipping time was very good! will use them again when I have the need.
Stephen from League City, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My Turntable Coupler was broken
I took the glass table up and underneath was the turntable coupler. I reached in with my hands and gently pulled the old coupler out. Once out I lined up the new one and gently pushed it in the hole until it locked into place. The process took about 5 minutes to complete. Very easy to install.
Teresa from Fredericksburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken turntable coupler
Pulled off old coupler.It was tight so used a trim bar to remove. Checked motor shaft since there was 2 types available.One, square shaft,other D shaft. Ordered in AM and received the next day in PM by Fedex.. Can`t get much better than that! Pushed on and done......Like new again...
CARL from CAMBRIDGE CITY, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old turntable coupler caught fire and burnt up
Replaced part with minimum effort.
Arun from Annarbor, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
0 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
November 30, 2017
I need the turntable coupler part jvm1630otr8. Apparently this part isn't available since I can't find it anywhere.What is the replacement model for the coupler I need to get that will fit this Hotpoint?
For model number RVM1625SJ01
Hello John, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is Part Number: PS227859. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Buzz
June 24, 2019
Can you tell me the size of the screw that holds the turntable motor in place. Misplaced.
For model number jvm1650sh05
Hello Buzz, Thank you for the question. Very sorry but we do not have the dimensions for this screw. For more specialized assistance or to speak with someone about this, I would suggest calling the manufacturer of the appliance directly. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Larry
March 8, 2023
How to remove and replace this turntable coupler
For model number JVM1650WH01
Hi Larry, thank you for reaching out. Firstly, unplug the appliance power cord. Then open the oven door to access the glass tray. Just remove the glass tray, and pull the turntable coupler straight upward. Now install a new turntable coupler, align it with a motor shaft, and position the glass tray on the coupler. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Larry
March 9, 2023
How do you replace the Drive Motor for this model ?
For model number JVM1650wh01
Hi Larry, thank you for reaching out. We would recommend following these general instructions to replace the drive motor, part number PS237772: First, turn off the power supply to the unit. Remove all the screws securing the bottom panel and lower it. Disconnect the wire harness from the drive motor, and then remove the mounting screws. Rotate the motor clockwise to detach it. To install the new motor, insert the motor shaft into the drive coupler. Rotate the motor anti-clockwise, and insert the mounting screw. Reconnect the harness wire to the drive motor and put the bottom panel back on. We hope this information is useful!
