![Customer Service Representative](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/images/csr-partdetail.jpg)
Drum Glide Bearing - White (Sold individually) WE3M51
Rated by 5 customers
Easy
1- 2 hours
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Drum Glide Bearing - White (Sold individually) Specifications
![How Buying OEM Parts Can Save You Time and Money How Buying OEM Parts Can Save You Time and Money](https://img.youtube.com/vi/d6AvOkulk_g/maxresdefault.jpg)
How Buying OEM Parts Can Save You Time and Money
Replacing your General Electric Dryer Drum Glide Bearing - White (Sold individually)
![Replacing your General Electric Dryer Drum Glide Bearing - White (Sold individually) Replacing your General Electric Dryer Drum Glide Bearing - White (Sold individually)](https://img.youtube.com/vi/iSX0twmb3kc/maxresdefault.jpg)
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
-
Samuel from PHILADELPHIA, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench set
Reviewed YouTube videos.
Patience is required, take your time, take photos of the wires and also make a written wiring chart. This was the flaw in my planning. Reference the schematics f ... Read more rom PartsSelect to number the controls. Do NOT use masking tape to identify the wires as they will have all stuck together by the time you go to reinstall them.
Most difficult process was removing and identifying the numerous wires to the back panel. They have push connectors, but some were very difficult to remove. The people doing the "how to" videos no doubt had them partially released and that made it look easy. Examine the connectors before removing to identify how they are captured by the connector. A paper clip "tool" I made enabled me to release some of the capture lugs, but some were so tight, I had to use small needle-nose pliers to open up the lug to release the wire on the connector.
When reinstalling, re-tighten those connectors.
Replacing the parts was much easier than the wiring disconnect/reconnect process. I'm happy to report that replacing the rear bearing and the front 2 green and 2 white shim/bearings immediately and completely solved my problem. For about $150, I restored my dryer to "like-new" functionality and got a lot of satisfaction from doing it. The project took about 4 hours, which could have been reduced to 2 hours had I know about the clip release and wiring identification process. Also, make sure you thoroughly vacuum out your unit while it is disassembled. Good luck!!!
-
mike from SUMMERVILLE, SC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
-
Robert from DECATUR, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set, Wrench (Adjustable)
-
Larry from LAS VEGAS, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
-
Maurice from MINERAL SPGS, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
- < Prev
- 1
- Next >
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
![](https://img.youtube.com/vi/nfH9wFqk_gM/maxresdefault.jpg)
6 people found this helpful.
6 people found this helpful.
1 person found this helpful.
![](https://img.youtube.com/vi/88l5LU_1S1Y/maxresdefault.jpg)
1 person found this helpful.
![](https://img.youtube.com/vi/nfH9wFqk_gM/maxresdefault.jpg)
- < Prev
- 1
- Next >
![Drum Bearing Sleeve – Part Number: WE1M462](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/266777-1-N-GE-WE1M462-Drum-Bearing-Sleeve.jpg)
![Duct Felt Seal – Part Number: WE09X27634](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/12722961-1-N-GE-WE09X27634-Duct-Felt-Seal.jpg)
![Drive Belt – Part Number: WE03X29897](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/16542496-1-N-GE-WE03X29897-Drive-Belt.jpg)
![DRYER BEARING SLIDE 2-PACK – Part Number: WE03X34318](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/assets/images/noimage_N.jpg)
Manufacturer Part Number: WE3M51
![Customer Service Representative](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/images/csr-partdetail.jpg)
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.