Part Location Diagram of 5303931775 Frigidaire M Series Ignition Coil Kit
See part 71 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

M Series Ignition Coil Kit 5303931775

 Fits your GL27M6WAFA!
★★★★★
★★★★★
24 Reviews

Rated by 41 customers 

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

$ 21.45
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your GL27M6WAFA!
PartSelect Number PS470049
Manufacturer Part Number 5303931775
Manufactured by Frigidaire
Product Description

M Series Ignition Coil Kit Specifications

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the symptoms that this kit could be a solution for are: If there is no heat, not enough heat, or clothes takes too long to dry. In this case, the gas valve coils can be defective and replacing this part will help. Customers rate this project as easy. Refer to the installation diagram for further instructions. For safety, unplug your dryer before repair.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Not Heating
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Westinghouse.
Part# 5303931775 replaces these:
AP2150379, 3449, 5303931775, 08015679, 08015680, 3201243, 3201244, 3281142, 3281143, 5300622602, 5303307291, 5303307292, 5303931775, 5308015680, 8015679, 8015680, F140570-300, F140570-400, G140570-300, G140570-400 , Q000622601, Q000622602, Q622601, Q622602, WQ622601, WQ622602 Show less
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
24 Reviews
4.6
Filter By Rating:
  • 5 Stars
    18
  • 4 Stars
    4
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Star
    1
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
  • 3
Customer Repair Stories
 Average Repair Rating: 3.8 / 5.0, 41 reviews. What's this?
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing installation instruction that matched.
No heat to dry clothes.
There was a lot of screws. And I cleaned everything well. The one part was bad so I replaced them all to make sure it'll last.
Other Parts Used:
Igniter M Series Ignition Coil Kit Flame Sensor
  • James from SAGINAW, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Flame would come on and go out,and little or no heat
Unhooked power,shut off gas, pulled top cover off,two Philips screws one on each side hold the front panel in.took belt off, pulled drum,than change out, flame sensor,M coils,and igniter,be careful igniter breaks very easy,I broke my new one so had to use my old one so really the problem with no heat was either the Mcoils or the flame sensor
Other Parts Used:
Igniter Upper Drum Glide M Series Ignition Coil Kit Flame Sensor
  • Gary from Columbus, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas dryer would generate heat at the beginning of the cycle but would stop after 5 min and would start making a buzzing noise.
Unplug from electric outlet. Use putty knife to press on two brackets holding the top cover. Raise top cover. Unscrew two screws holding the front panel. Raise front panel up and move to the right (careful with the wires). Disconnect wires from coils. Unscrew two screws holding a small bracket holding the coils. Replace coils and reassemble everything. (HINT: make sure you drum is empty. Mine contained dump clothes, and it turned out front panel actually provides support to the drum, so mine was hanging there with some weight in it - probably not good).
  • Denis from LONGMEADOW, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas burner worked sometimes only.
Dryer was working, only burner was working occasionally only. So, in result the drying time was very long, and clothes were cold and still not satisfactionally dry; occasionally only it was hot. It became obvious to me that gas burner only occasionally is working. On the Internet I found some instructables, mostly on YouTube, but also on this site (the Burner diagram): thus I have learned that the culprit must be the two tiny ignition coils: they worked only sometimes, so it was only a jeopardy when checking them using a continuation meter (voltmeter with continuation feature). For the access to the burner combo I used a small checking door right below the large door, in front wall of the dryer. There are only two small screws which hold a small piece of metal which cover these tiny coils. However, I had to disconnect the burner from gas pipe to get better access to those screws. (Of course, I also disconnected the dryer from power and I had to disconnect those wire connections on the burner combo to get access to the burner). It works perfectly after this repair.
  • Marek from CHICAGO, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer did not completely dry the clothes. It required several cycles to dry clothes.
I unplugged the dryer and pryed open the top by inserting a screw driver in the space 1inch from the top on the side. After i opened it and lifed it up, I removed the one screw on both sides found in the inner part towards the front top. I then removed the front panel. The coils are toward the bottom left side. They are held in by a bracket which is held in by 2 screws. I removed the outer screw and loosened the inner screw. ( you can remove both screws but it was not necessary).I then swumg the bracket around and was able to lift out the coils. I removed the connectors and relaced the coils. Once done I re-assembled the dryer. The problem was solved.
  • Lester from CHICAGO, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat
Raise the top and remove the front panel assembly. One philips screw, 24mm gas line coupler and 3 electrical connectors frees the burner assembly. Slid the old igniter out and the new one in.2 philips screws to remove the coil retainer and replace the coils.
Other Parts Used:
Igniter M Series Ignition Coil Kit
  • Matthew from JOLIET, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer not heating up consistently
My dryer was heating up very briefly blowing hot air initially then cool. I have a stacking washer/dryer set (2002). I initially turned off the gas valve at the wall, ran the dry for several minutes to clear the gas line, then unplugged the power. I was then able to pop the top using a flathead screw driver, securely prop it open, unhook the wiring harness to the front panel, unscrew the two front panel screws, and remove the entire front without having to unstack the units. From there, you remove the two screws holding the bracket over the coils (2 of them), remove the electrical connectors attached to both coils and replaced them with the new ones. I then replaced all brackets, screws, and such (you'll need to lift the drum when putting the front back on and make sure it is lined up), plugged it back into power and turned on the gas to test the unit which worked perfectly. The 62% of the time seems to be an accurate figure as nothing else had to be done to the unit. Pretty easy stuff...good luck.
  • Case from Los Angeles, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat/intermittent heat. Ignitor glowed but no gas flame.
White Westinghouse WDG547PB Dryer. Removed access panel (lower left front of dryer) by removing phillips head screw below access panel. Removed two phillips head screws holding bracket that holds coil in place. Removed coil, disconnected electrical connector. Connected electrical connector to new coil and set in place. Repeat for second coil. Reinstall bracket and access panel. Job complete. Dryer back in service with no problems.
  • Jeffrey from Richmond, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
11 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat.
As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obvious (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.
  • Steven from San Francisco, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no heat to dryer at startup
Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.
  • DAN from FELCH, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

14 questions answered by our experts.
Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sam
December 13, 2017
I change the igniter because was not lighting and then was still the same, I check for power to the igniter and was going power but still not lighting.
For model number fgq332es2
PartSelect logo
Hi Sam, Thank you for the question. I suggest trying to replace the 'M' Series Ignition Coil Kit,PartSelect Number PS470049. You can also test them with a Multi-Meter. The two prong coil will read 1,000-1,300 ohms, and the three prong coil will read 1,300-1,400 ohms across prongs 1&2, and 500-600 ohms across prongs 1&3. Hope this helps.

12 people found this helpful.

Was this helpful?
Thank you for voting!
John
August 12, 2017
My dryer will not light. I see the heating coil come on and get hot, but no Flame. Could it be the ignition coil kit? Thanks.
For model number FGQ1442ES0
PartSelect logo
Hi John, Thank you for your inquiry. In most cases this part is the problem and needs to be replaced. You could also check your radiant flame sensor with a multi-meter to see if that part is malfunctioning at all. That is the second most likely part to cause a problem like this. While you are testing parts I would also suggest testing your control thermistor as well. Good luck with your repair!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Bob
June 9, 2019
My dryer is not heating up. I had the issue of it not turning and ordered a drum belt from you and got that issue fixed. I read your previous replies about checking the coils with a multi meter to see if they are bad. Before I remove the coils to check them, do I need to turn off the gas to the dryer? I have a multi meter to check with.
For model number FDGB23RGS1
PartSelect logo
Hello Bob, Thank you for the question. Yes, the gas should be turned off before checking the coils. Hope this helps!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Ron
March 4, 2018
Dryer will dry for awhile then shut off. Have been using dryer on touch up setting. This dries but only cycles for 15 minutes at low heat setting. Is my issues in the moisture sensor? Thank you.
For model number AGQ7000ES0
PartSelect logo
Hi Ron, Thank you for the question. Sounds like you will need to replace the Interface Board/Timer, PartSelect Number PS1152216. This board tells the element when to heat up. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Jim
February 22, 2018
Hi, i am replacing the coils on a combo dryer. The instructions above seem to be for a stand alone. How do i replace these coils and also the starter switch? Thanks for any help.
For model number GLGT1142CS1
PartSelect logo
Hello Jim, thank you for your question. Even though the repair video is for a stand alone dryer, the installation on your unit would be the same. Once you gain access to the heater section, by removing the slanted panel under the dryer control panel, there will be a safety cover that can be removed. All the heater, coils, thermostats should be visible from there. You could then follow the following instructions for installing the coils: Remove 2 Phillips screws with short handled Phillips driver that hold the gas valve coil bracket in place. Unplug and remove both coils, installed new coils and bracket. Re installed safety panel, screws and slanted cover. I hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Rich
February 20, 2019
I replaced the Flame sensor and the coils at the same time still takes over 3 hours long to dry. What can I do?
For model number FAQG7001LW0
PartSelect logo
Hello Rich, Thank you for the question. I suggest checking the Control Thermistor, PartSelect Number PS1149368.This part controls the temperature of the inside of the dryer drum. This part is located in the blower housing. This part can be tested with a multi-meter. It should ready 50K ohms of resistance at 77 degrees F. Thank you for your inquiry, good luck with this repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
John
November 28, 2017
Will this kit work with propane? If not do you have one that will? Thank you
For model number AGQ7000ES1
PartSelect logo
Hi John, Thank you for your question. Yes it will. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Boris
November 30, 2017
How many 'm' series ignition coil kit i need
For model number DG400AXW2
PartSelect logo
Hi Boris, Thank you for your question. You will just need to buy one 'm' series ignition coil kit for your appliance. I hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
Mike
January 11, 2018
I replaced this part igniter still doesnt glow and cant here gas turn on whats next?
For model number FAQG7011LW0
PartSelect logo
Hi Mike, Thank you for your question. If you have already replaced the coils, there are some other parts that you will need to check to see which one is causing the issue. You will need to check the flame sensor, the control thermistor, the igniter, the limiter, the blower housing and wheel, and the thermostat. I hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
Randy
June 17, 2021
My dryer won't heat up, heating element heats up for a period of time, then click, no flame and heating element turns off. Gas valve problem or coil problem?
For model number GLGQ2152ES0
PartSelect logo
Hello Randy, Thank you for the question. We suggest testing the M Series Ignition Coli Kit. The two prong coil will read 1,000-1,300 ohms, and the three prong coil will read 1,300-1,400 ohms across prongs 1&2, and 500-600 ohms across prongs 1&3. You can also test the Dryer Burner Igniter. They should be reading between 0 - 1100 ohms to be working correctly. We hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
  • 2
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS470049
Manufacturer Part Number: 5303931775
Brand
Model Number
Description
Kenmore
41759012890
Dryer - Kemore Dryer 41759012890
Frigidaire
41759022890
Dryer - Gas
Kenmore
41771712510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771712511
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771712512
Washer Dryer Combo - Laundry Center
Kenmore
41771722510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771722511
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771722512
Washer Dryer Combo - Laundry Center
Kenmore
41771723510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771723511
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771723512
Washer Dryer Combo - Laundry Center
Kenmore
41771732810
Washer Dryer Combo - Laundry Center
Kenmore
41771733810
Washer Dryer Combo - Laundry Center
Kenmore
41771733811
Washer Dryer Combo - Laundry Center
Kenmore
41774182300
Dryer
Kenmore
41774182301
Dryer
Kenmore
41779042900
Dryer - Kenmore Dryer Model 417.79042900 (41779042900, 417 79042900) Parts
Kenmore
41779042990
Dryer
Kenmore
41779042991
Dryer
Kenmore
41779052990
Dryer
Kenmore
41779052991
Dryer
Kenmore
41788980100
Dryer - Kenmore Dryer Model 417.88980100 (41788980100, 417 88980100) Parts
Kenmore
41788989100
Dryer
Kenmore
41788989800
Dryer
Kenmore
41790032990
Dryer
Kenmore
41790042990
Dryer
Kenmore
41790042991
Dryer
Kenmore
41790052990
Dryer
Kenmore
41790052991
Dryer
Kenmore
41790142000
Dryer
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service