Quick Question!

Have you ever purchased from PartSelect.com before?

459818-1-S-Frigidaire-5303281135        -Flame Sensor
459818-1-S-Frigidaire-5303281135        -Flame Sensor 459818-2-S-Frigidaire-5303281135        -Flame Sensor 459818-3-S-Frigidaire-5303281135        -Flame Sensor https://www.partselect.com/Schematics/Frigidaire/DBHHKCTB.gif

Flame Sensor

Your Price

$22.09
Order within the next 12 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS459818
Manufacturer Part Number 5303281135
Manufactured by Frigidaire

This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer is not giving off enough heat. If your clothes are not drying at a reasonable time, this might be your first indication of an issue. You will need to remove the two screws underneath the lint cover to remove the top of the appliance. Release the door switch wiring, remove the front panel, and remove the belt off the pully. You should now be able to completely remove the drum from the dryer. This will give you access to the sensor for the repair.

This part works with the following brands: Frigidaire, Kenmore, Gibson, Kelvinator, Westinghouse, Tappan, Electrolux, Crosley.

This part works with the following products: Dryer, Washer Dryer Combo.

This part fixes the following symptoms:

  • No heat or not enough heat.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 5 reviews What's this?
1-5 of 5
 

60 of 70 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Dirk from Sonoma, CA

Dryer won't stay hot, gas smell

Pulled unit out from wall to access back panel. Top needs to be removed to get to the screws that hold on the front panel and door. These need to be removed to get to the valve and burner.

Once your in, the sensor, thermostat, and igniter are right up front. Sensor and thermostat were easy, the igniter breaks very easily...how do I know? Cause I broke the one I bought and had to get a new one.

I also replaced the coil set for the gas valve, because I had read that they can go bad and cause a gas fume smell. The coils are cheap, so you may as well as do them at the same time.

Anyway, once the repair was complete, I reassembled the unit and hooked up the vent.

Runs like new, and the clothes dry quickly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 22 people found this instruction helpful

Parts Used:
  • Flame Sensor
Level of Difficulty: Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Giuseppe from San Francisco, CA

Gas flame turns off after a while. No more heat.

Fixed it eventually with part PS470049 ('M' Series Ignition Coil Kit). See separate story.

The flame sensor did not fix it but read on for info on how to replace this part. Before replacing this part, I should have read another posting in a different web site about the ignition coils: if you see a red glow inside the burner unit but the flame does not come on, then the problem is likely to be with the coils, not the flame sensor. However since some users here had solved the problem by replacing the flame sensors, I figured I'd try it. The setting for "More dry, less dry" never worked either so maybe this would fix two problems at once.

This dryer is a stacked front loader sitting on top of our washing machine. Opening the little front door (lower left side) is easy once you figure out that a little screw below needs to be removed. I almost broke the door trying to pull it open. The sensor is attached to the side of the flame area cylinder. It was hard to remove both the screw and the part itself from the slots as it's very springy. In fact when I finally removed it, it dropped to the base of the unit and sparks went flying as one of the electrical clips touched the metal (ground). Tip: first disconnect the electrical lead coming from the back of the unit to the ingnition block and later I used rubber gloves just in case. (I could not access the plug/outlet in the back). I installed the new part easily, though I was confused by the electrical leads: the white wire connects to the lead that has a red plastic dot on the side, but I think that must be a mechanical part and not a (wrong) marking, while the red connects to the other lead. Anyway, I connected it the same way I found it and put it back. Reconnected the other electrical wires and closed the door.

This did not fix the problem which turned out to be with the gas valve coils: as they get old, they turn off the flame when they get hot, even though the dryer keeps on turning. To read how to replace that part, search for comments under part number PS470049 ('M' Series Ignition Coil Kit). I don't know whether replacing the flame sensor is going to fix the "more dry-less dry" function, will have to see. Still, this website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fixes it's just like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

16 of 18 people found this instruction helpful

Parts Used:
  • Flame Sensor
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: David from Murrieta, CA

Dryer would not ignite

Make Sure Dryer is off and disconnected from power! Also, beware of sharp edges on dryer parts and cabinet.
1) Popped-off top lid with flat-blade screw driver (Insert screw driver in joint between top and front of dryer above door) Spring clips are all that's holding top on in front
2) Unplugged plastic electrical connector located just along the top-right side of dryer
3) Removed one sheet metal screw located about 8" down from top on either side of dryer - total of two screws
4) Pull front of dryer back and pull up at bottom of dryer (Remember that when you replace front you will have to make sure plastic bearing surfaces on dryer tub are centered back in cut-out on front panel. Plastic tabs fit inside the cut-out or else you'll ge a swishing noise when tub rotates)
5) Set front panel to side
6) Flame sensor is located on the left side of the burn chamber sheet metal cover. It has a red and white wire with flat connectors that must be pulled off. Note which color goes to what terminal
7) Unscrew fastener. Note: this screw/fastener needs a non-standard driver to get it out. I have a variety of other drivers beyond phillips/flat types and non of them worked.
8) I ended up using a pair of pliers to just work it out from under the screw. I bent it, as it has a tab that slips in along left bottom edge of burn chamber cover.
9) Finish taking screw out by hand
10) Put new flame sensor in by inserting tab on bottom first. Then, screw in fastener to top of sensor bracket and reconnect wires. White on top and red on bottom terminal.
11) Replace front panel with door by placing in tabs on bottom front of dryer. Again, make sure plastic bearing surfaces are inside of circular flange on front panel
12) Make sure to reconnect plastic cable connector. Note: I added a tie-wrap because it looked like the connector might rub against drum. There are some holes through which you can run the tie-wrap
13) Replace the two sheet-metal screws
14) Push top down so spring clips re-engage with dryer body

Help other customers find the most helpful instructions.

Were these instructions helpful?   

16 of 19 people found this instruction helpful

Parts Used:
  • Flame Sensor
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Joy from Lakeville, MN

No heat in the dryer

unplugged the dryer, discontected the sensor and unscrewed the bracket, replaced the new one and put the connectors back on, screwed the bracket back on and that was it. Very easy fix for a female who does not do much of these sort of repairs but learning.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Flame Sensor
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Wrench (Adjustable)
Customer: stefan from alpena, MI

The igniter glowed red and the gas did not come on !

Read your article on possible repairs for different symptoms and after dis assembling and cleaning certain parts took a chance on the flame sensor, which turned out to be the culprit. Your help was a valuable tool in the repair process ! What would be the bee's knee's would be the resistance reading on the sensors that monitor the system for a more accurate diagnostic approach. But none the less you definitely aided in the repair of my propane gas dryer. Thank you very much ! And by the way the 3-4 day wait for the part was well worth the half price I paid versus our small town repair facility, Thanx again

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5

Model Cross Reference

This part works with the following models:

PartSelect Number: PS459818
Manufacturer Part Number: 5303281135
Brand Model Number Description
Kenmore41759012890Dryer - Kemore Dryer 41759012890
Frigidaire41759022890Dryer - Gas
Kenmore41774182300Dryer
Kenmore41774182301Dryer
Kenmore41779042990Dryer
Kenmore41779042991Dryer
Kenmore41779052990Dryer
Kenmore41779052991Dryer
Kenmore41788989100Dryer
Kenmore41788989800Dryer
Kenmore41790032990Dryer
Kenmore41790042990Dryer
Kenmore41790042991Dryer
Kenmore41790052990Dryer
Kenmore41790052991Dryer
Kenmore41790142000Dryer
Kenmore41790412700Dryer
Kenmore41790412701Dryer
Kenmore41790862990Washer Dryer Combo
Kenmore41790862991Washer Dryer Combo
Kenmore41790862992Washer Dryer Combo
Kenmore41790872990Washer Dryer Combo
Kenmore41790872991Washer Dryer Combo
Kenmore41790872992Washer Dryer Combo
Kenmore41791042000Dryer
Kenmore41791042001Dryer
Kenmore41791052000Dryer
Kenmore41791052001Dryer
Kenmore41791100000Dryer
Kenmore41791101000Dryer