Tub Seal Assembly 5303279394 | Official Frigidaire Part | Fast Shipping | PartSelect
Tub Seal Assembly – Part Number: 5303279394
Tub Seal Assembly – Part Number: 5303279394 Tub Seal Assembly – Part Number: 5303279394 Tub Seal Assembly – Part Number: 5303279394 Tub Seal Assembly – Part Number: 5303279394 https://partselectcom.azureedge.net/Schematics/Frigidaire/DVCTCK76.gif

Tub Seal Assembly

Product Description

Tub Seal Assembly Specifications

If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of this piece is to make sure water does not lead from between the outer tub and the spin basket from around your basket drive shaft within your washer. To replace your old part with this one you will need a flathead screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16 socket, spanner wrench, and a hammer.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Leaking

This part works with the following products:

Washer, Washer Dryer Combo.

This part works with the following brands:

Frigidaire, Kenmore, Westinghouse, Gibson, Tappan, Crosley, Kelvinator, Uni, Electrolux.

Part # 5303279394 replaces these:

461, 5308027482, AP2142342, N8027481, N8027482, NF14184210, NF141842-100, NF14184220, NF141842-200.
Questions and Answers
Ask our experts a question on this part and we'll respond as soon as we can.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer Repair Stories
Average Repair Rating: 2.4 / 5.0, 7 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Rick from Walkerton, IN
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set
Parts Used:
5303279394, 131862900, 131545101, 131219900
The primary problem was that the tub seal assembly was leaking.
1. I began by removing the two screws that hold the front panel in place. I then lifted the top free of the front panel and tilted it back to get it out of the way.

2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.

3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.

4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.

5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.

6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.

The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy.
238 of 299 people found this instruction helpful.
Was this instruction helpful to you?
Patrick from Humble, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set
Parts Used:
5308002401, 5303279394, 3204405, 131557201, 131398303, 131076600
Noisy spin cycle
1) Unplugged washer and disconnected the hot and cold hoses.
2) removed the 2 phillips screws at the bottom of the front panel then removed front panel, you need enough clearance by the floor, this is tricky because you have to lean washer back and push down on the front panel.
3) removed the agitator from the washer
4) lifted top of washer and leaned back against the wall and removed the splash tub cover one clip at a time with a flat screw driver.
5) removed the trunion, this is difficult and will take some time due to the corrosion from many years of use use a hammer (3Lb short handle) and tap one side then the other. You will need to rock it back and forth awhile.
6) lift the basket out of splash tub
7) I removed the hose for water level and removed the 3 bolts that hold the splash tub to the three base mounts (support arms).
8) remove the splash tub
9)change the plastic washer that is between the splash tub and the transmission in the bottom of the splash tub
10) change the bearing(metal sleeve) on the bottom of splash tub and lightly grease w/ a thin film of teflon grease
11) install splash tub and install the 3 bolts along w/ the water level tube
12) install the larger seal (w/ spring in it) and push into the splash tub firmly
13) use some tub and faucet silicone grease on the smaller seal because you don't want to damage this main seal, install the main seal (sits on top of the larger one that's in the tub already) be careful when getting to flat part of the shaft when installing ( spin around the shaft as you pass this point) it will keep the seal from coming out.
14) install trunion (sits down on top of the seal) you will feel the tension of the spring when bolting the trunion back into place.
15) install basket and bolt it to the trunion (I installed a new filter on the bottom of the basket and required some special glue, ask for "3M" GMGA600 adhesive.
16) installed splash tub cover, agitator and front cover.
Washer works great and is quieter than it was new.
128 of 153 people found this instruction helpful.
Was this instruction helpful to you?
dave from port sanilac, MI
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
Parts Used:
134736400, 134418700, 5303279394
bearing and seal at top of transmission went bad causing oil from transmission to stain clothes
I removed front and top of washer to get acess to the tub. removed cap to tub along with inner tub and agitator. the hardest part is removing the springs on the bottom and tilt it forward to get tub out. removed belt, pulley and bolts holding transmission in place. reassemble using silicone grease on seals and washers. works great now
56 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Michael from Springfield, VT
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set
Parts Used:
5303279394
Washer not spinning, water leaking out bottom
My first step was to download and print out the parts diagrams from the manufacturer's website. With a basic idea of what I needed to get to I first removed the agitator cap and the agitator and right off I found a broken bolt on plate lock bracket that holds trunnion which supports and connects the tub to the transmission drive shaft. I replaced the bolt and put it back together and gave it a test run. Spun very nicely now but water was going everywhere. Unfortunately I found that when the bolt broke the tub had slipped down and ripped the rubber "tub seal assembly". To get to the seal I ended up tearing the machine completely down and removing the whole motor and transmission assembly out of the unit. It may be possible to get at the seal without doing this but I'm not 100% sure. To get the whole unit apart I did the following: Remove the front panel by removing the two screws located at the very bottom of the panel and lifting up and out .Remove the top/lid by removing two screws underneath the top toward the front, and disconnecting lid switch, or i found it easier to just unscrew and remove it, then lift off the top/lid assembly. Remove the agitator cap and the agitator. Remove the splash cover (this is not easy- I popped each tab with a flat screw driver- the ones at the rear were very difficult). I tried to remove the fill spigot but could not get at one of the screws so getting the splash cover out was not as easy as it could have been. Remove the bolts in the bottom of the tub and lift it out. Unhook the drain hose and the level or "pressure tube". Remove the 3 large and 3 small springs from the motor assembly ( I needed a strong spring hook but all I had was vice grips, they work but it was not easy). remove any other wires etc. (mark things with tape and matching numbers if needed) and pull out the whole barrel and motor assembly. Unbolt the splash tub and remove, unbolt the trunnion and remove. And finally replace the seal. Reassemble in reverse order. Important!! Clean shaft well (I used some 300 grit fine sandpaper to remove the little bit of rust scale that had accumulated) and lubricate everything. be very careful when reassembling, as to not scuff up the seals at all. I used a silicone spray. This might not be the best thing for the job but I know at least not to use anything petroleum based such as WD-40 when you are lubricating rubber or plastic. Reinstalling the springs was very difficult and again a spring hook would have been great. Everything else went together reasonably easy. The unit works fine now. many thanks to the websites I researched to get this done.
27 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Gregory from Fort Worth, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Parts Used:
5303279394
Tub was leeking
Lifted top
removed adgetator
removed tub top
removed inside tub
removed inside tub holder bracket
repaced seal
replaced,replaced.....
13 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Bob from Plantation, FL
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Parts Used:
5303279394, 131427200
Bearing went bad where the tub attaches to the transmission
It is a stacked washer and dryer so I had to completely disassemble the dryer so I could take the washer apart to get to the bearing. You had most of the parts except the bearing but I was able to find it on the internet. Actually work has picked up so I haven't gotten it back together yet but I hope to do so Thanksgiving weekend.
13 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Martinus from Fort Lauderdale, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench set
Parts Used:
5303279394
Leaking water from machine
This repair is realy very easy
As discribed by the others
10 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
3 Reviews
5
out of 5
Filter By Rating:
  • 5 Stars
    3
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS459481
Manufacturer Part Number: 5303279394
Brand
Model Number
Description
Kenmore
417.99985840
Washer Dryer Combo - Kenmore Washer/Dryer Combo Model 417.99985840 (41799985840, 417 99985840) Parts
Kenmore
41790802990
Washer Dryer Combo
Kenmore
41790802991
Washer Dryer Combo
Kenmore
41790802992
Washer Dryer Combo
Kenmore
41790807990
Washer Dryer Combo
Kenmore
41790812990
Washer Dryer Combo
Kenmore
41790812991
Washer Dryer Combo
Kenmore
41790812992
Washer Dryer Combo
Kenmore
41790814000
Washer Dryer Combo
Kenmore
41790814001
Washer Dryer Combo
Kenmore
41790814002
Washer Dryer Combo
Kenmore
41790817990
Washer Dryer Combo
Kenmore
41790862990
Washer Dryer Combo
Kenmore
41790862991
Washer Dryer Combo
Kenmore
41790862992
Washer Dryer Combo
Kenmore
41790872990
Washer Dryer Combo
Kenmore
41790872991
Washer Dryer Combo
Kenmore
41790872992
Washer Dryer Combo
Kenmore
41791702000
Washer Dryer Combo
Kenmore
41791702001
Washer Dryer Combo
Kenmore
41792702200
Washer Dryer Combo
Kenmore
41793702200
Washer Dryer Combo
Kenmore
41793702201
Washer Dryer Combo
Kenmore
41793802200
Washer Dryer Combo
Kenmore
41793802201
Washer Dryer Combo
Kenmore
41793812200
Washer Dryer Combo
Kenmore
41793812201
Washer Dryer Combo
Kenmore
41793814200
Washer Dryer Combo
Kenmore
41793814201
Washer Dryer Combo
Kenmore
41793862200
Washer Dryer Combo