452574-1-M-Frigidaire-5300809909 -Motor Shaft Seal Kit
Part Location Diagram of 5300809909 Frigidaire Motor Shaft Seal Kit
See part 10 in the diagram
( Grid squares measure 1x1 inch )
452574-1-S-Frigidaire-5300809909 -Motor Shaft Seal Kit 452574-2-S-Frigidaire-5300809909 -Motor Shaft Seal Kit 452574-3-S-Frigidaire-5300809909 -Motor Shaft Seal Kit Part Location Diagram of 5300809909 Frigidaire Motor Shaft Seal Kit
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Motor Shaft Seal Kit 5300809909

★★★★★
★★★★★
1 Review

Rated by 2 customers 

A Bit Difficult 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 55.78
  Special Order
Get FREE EconoShip on orders over $100! T&C apply
PartSelect Number PS452574
Manufacturer Part Number 5300809909
Manufactured by Frigidaire
Product Description

Motor Shaft Seal Kit Specifications

This motor shaft seal kit does not include a macerator blade, but does come with wash and drain impellers(upper and lower).
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking | Not draining
This part works with the following products:
Dishwasher.
This part works with the following products:
Frigidaire, Tappan, Kenmore, Amana.
Part# 5300809909 replaces these:
AP2135640, 662, 809909
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Jessica K - March 1, 2021
  Verified Purchase
Easy all around
Fast delivery and great selection
  • 1
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.1 / 5.0, 2 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water leaking from motor shaft under dishwasher
DISASSEMBLY
- Switch off circuit breaker for dishwasher.
- Remove lower front covers from washer to observe motor (for later steps) and to clean-up water.
- Remove top and bottom dishracks.
-You may want to take pics of the placement/orientation of components in the following steps as you disassemble them for reference during reassembly.
- Remove spray-arm base from pump housing.
- Remove and discard impeller— put a screwdriver in the impeller grooves to prevent it turning as you loosen the screw.
- Remove impeller, O-ring, and blade. Discard impeller and O-ring, but keep blade (I couldn’t find the O-ring; it had probably disintegrated).
- Remove pump housing, pump plate, and gasket.
- Use two flat-head screwdrivers on opposite sides of the rotor to pry it off the motor shaft. Be cautious not to damage the area around the motor shaft—wood can be used to protect the area and provide better leverage. If the rotor can’t be removed, a chisel or hacksaw can be used to split it before prying it up— be cautious of the motor shaft when splitting the rotor. Discard the rotor.
- Locate the upper seal, note its orientation (cup-side-down), remove it, and discard it (my upper seal was in the recess in the bottom of the rotor).
-Drive the shaft-key (small metal tab) out of the shaft groove using a hammer and flat-head screwdriver and discard it— the new rotor has a molded-in tab that will slide into the groove in place of the shaft-key.
- Remove ceramic ring from motor shaft and discard it (my leak was caused because the ceramic ring was broken in half).
- Use a flat-blade screwdriver to pry loose the lower seal—before removing it from the shaft, note its orientation (wide-side-down). Be caution not to damage the area around the motor shaft—wood may again be used for protection and leverage.

CLEANING/PREP
- Clean shaft with wire brush, white vinegar, and a rag (you may not need the wire brush if the shaft is in good shape, but my motor shaft was heavily corroded/rusted and I needed to smooth it to prevent it damaging the seals). Clean groove in motor shaft with flat-head screwdriver and rag.
- Use a rag and white vinegar to clean motor shaft recess and pump housing seat. The bottom of the motor shaft recess must be clean and smooth for the lower seal to seat properly.
- Clean pump plate, gasket, blade, pump housing, and screws with white vinegar and a plastic-bristled brush.

ASSEMBLY
-Wet new rubber seals, new ceramic ring, and new rotor with water to help them slide into place.
-Refer to pics taken during disassembly as needed for the following steps.
- Place new lower seal (wide-side-down) over motor shaft in bottom of recess.
-Push new upper seal (cup-side-down) into recessed area in the bottom of the new rotor.
-Push new ceramic ring into upper seal (cup-side) in bottom of rotor.
-Align groove on motor shaft with tab in rotor (a mark on the outside of the rotor shows the tab’s location) and seat rotor on the motor shaft by hand. Verify that the motor turns when the rotor is turned by hand. If not, remove the rotor and reposition it so that its tab slides into the groove in the motor shaft.
-Place gasket, pump plate, and pump housing in position. Start pump housing screws, but leave them loose.
- Place blade and new O-ring on rotor.
- Place new impeller on rotor and insert screw. Tighten moderately — overtightening could cause leaks. Hold the impeller by hand to prevent it turning as the screw is tightened— do not use a screwdriver to prevent the impeller turning.
- Finish tightening pump housing screws.
- Seat spray-arm base on pump housing and insert/tighten its mounting screws.
- Switch on circuit breaker for dishwasher.
- Start washer and watch motor to verify that shaft seal is not leaking. Run a full cycle to rinse the new parts and remove debris and vinegar residue. Continue to observe motor shaft area for leaks during cycle.
-Replace lower front covers.
Read less
  • Trevor from LOGAN, UT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
heard a noise while dishwasher was in operation, opened door and noticed the dishes were dry, no water was spraying out and dishwasher was making a whirling noise.
After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.
Read less
  • Joe from Arvada, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Be the first to ask our experts a question about this part!

Back to Top
You May Also Need ?
Pump Gasket
$40.87
$40.87
  On Order
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS452574
Manufacturer Part Number: 5300809909
Brand
Model Number
Description
Frigidaire
1031-005A
Dishwasher - DISHWASHER
Kenmore
58714249990
Dishwasher
Kenmore
5871429990
Dishwasher
Kenmore
5871430591
Dishwasher
Kenmore
5871433590
Dishwasher
Kenmore
5871434969
Dishwasher
Kenmore
5871444990
Dishwasher
Kenmore
5871501190
Dishwasher
Kenmore
5871504190
Dishwasher
Kenmore
5871511590
Dishwasher
Kenmore
5871710591
Dishwasher
Kenmore
58717245990
Dishwasher
Kenmore
5871733590
Dishwasher
Kenmore
5871734569
Dishwasher
Kenmore
58717345691
Dishwasher
Kenmore
58717345790
Dishwasher
Kenmore
5871744590
Dishwasher
Frigidaire
61-1014-00
Dishwasher - DISHWASHER
Tappan
61-1014-10-00
Dishwasher - 24" Built-in
Tappan
61-1021
Dishwasher - DISHWASHER
Tappan
61-1021-10-00
Dishwasher - 24" Built-in
Frigidaire
61-1043-10
Dishwasher - DISHWASHER
Tappan
61-1043-10-00
Dishwasher - 24" Built-in
Frigidaire
61-1073-10
Dishwasher - DISHWASHER
Tappan
61-1073-10-00
Dishwasher - 24" Built-in
Frigidaire
61-1083-10
Dishwasher - DISHWASHER
Tappan
61-1083-10-00
Dishwasher - 24" Built-in
Frigidaire
61-1093-10
Dishwasher - DISHWASHER
Tappan
61-1093-10-00
Dishwasher - 24" Built-in
Tappan
61-1120-00
Dishwasher - 24" Built-in
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Motor Shaft Seal Kit
$ 55.78
  Special Order
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.