Frigidaire/Frigidaire_Thumb/7SGM81QV.gif
See part 10 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Motor Shaft Seal Kit

★★★★★
★★★★★
1 Review
$39.01   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS452574
Manufacturer Part Number 5300809909
Manufactured by Frigidaire
Product Description

Motor Shaft Seal Kit Specifications

This motor shaft seal kit does not include a macerator blade, but does come with wash and drain impellers(upper and lower).
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking | Not draining
This part works with the following products:
Dishwasher.
This part works with the following products:
Frigidaire, Tappan, Kenmore, Amana.
Part# 5300809909 replaces these:
AP2135640, 662, 809909
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories
 Average Repair Rating: 2.1 / 5.0, 2 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    Water leaking from motor shaft under dishwasher
    DISASSEMBLY
    - Switch off circuit breaker for dishwasher.
    - Remove lower front covers from washer to observe motor (for later steps) and to clean-up water.
    - Remove top and bottom dishracks.
    -You may want to take pics of the placement/orientation of components in the following steps as you disassemble them for reference during reassembly.
    - Remove spray-arm base from pump housing.
    - Remove and discard impeller— put a screwdriver in the impeller grooves to prevent it turning as you loosen the screw.
    - Remove impeller, O-ring, and blade. Discard impeller and O-ring, but keep blade (I couldn’t find the O-ring; it had probably disintegrated).
    - Remove pump housing, pump plate, and gasket.
    - Use two flat-head screwdrivers on opposite sides of the rotor to pry it off the motor shaft. Be cautious not to damage the area around the motor shaft—wood can be used to protect the area and provide better leverage. If the rotor can’t be removed, a chisel or hacksaw can be used to split it before prying it up— be cautious of the motor shaft when splitting the rotor. Discard the rotor.
    - Locate the upper seal, note its orientation (cup-side-down), remove it, and discard it (my upper seal was in the recess in the bottom of the rotor).
    -Drive the shaft-key (small metal tab) out of the shaft groove using a hammer and flat-head screwdriver and discard it— the new rotor has a molded-in tab that will slide into the groove in place of the shaft-key.
    - Remove ceramic ring from motor shaft and discard it (my leak was caused because the ceramic ring was broken in half).
    - Use a flat-blade screwdriver to pry loose the lower seal—before removing it from the shaft, note its orientation (wide-side-down). Be caution not to damage the area around the motor shaft—wood may again be used for protection and leverage.

    CLEANING/PREP
    - Clean shaft with wire brush, white vinegar, and a rag (you may not need the wire brush if the shaft is in good shape, but my motor shaft was heavily corroded/rusted and I needed to smooth it to prevent it damaging the seals). Clean groove in motor shaft with flat-head screwdriver and rag.
    - Use a rag and white vinegar to clean motor shaft recess and pump housing seat. The bottom of the motor shaft recess must be clean and smooth for the lower seal to seat properly.
    - Clean pump plate, gasket, blade, pump housing, and screws with white vinegar and a plastic-bristled brush.

    ASSEMBLY
    -Wet new rubber seals, new ceramic ring, and new rotor with water to help them slide into place.
    -Refer to pics taken during disassembly as needed for the following steps.
    - Place new lower seal (wide-side-down) over motor shaft in bottom of recess.
    -Push new upper seal (cup-side-down) into recessed area in the bottom of the new rotor.
    -Push new ceramic ring into upper seal (cup-side) in bottom of rotor.
    -Align groove on motor shaft with tab in rotor (a mark on the outside of the rotor shows the tab’s location) and seat rotor on the motor shaft by hand. Verify that the motor turns when the rotor is turned by hand. If not, remove the rotor and reposition it so that its tab slides into the groove in the motor shaft.
    -Place gasket, pump plate, and pump housing in position. Start pump housing screws, but leave them loose.
    - Place blade and new O-ring on rotor.
    - Place new impeller on rotor and insert screw. Tighten moderately — overtightening could cause leaks. Hold the impeller by hand to prevent it turning as the screw is tightened— do not use a screwdriver to prevent the impeller turning.
    - Finish tightening pump housing screws.
    - Seat spray-arm base on pump housing and insert/tighten its mounting screws.
    - Switch on circuit breaker for dishwasher.
    - Start washer and watch motor to verify that shaft seal is not leaking. Run a full cycle to rinse the new parts and remove debris and vinegar residue. Continue to observe motor shaft area for leaks during cycle.
    -Replace lower front covers.
    • Trevor from LOGAN, UT
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Screw drivers, Socket set
    • Parts Used:
      5300809909
    2 of 2 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    heard a noise while dishwasher was in operation, opened door and noticed the dishes were dry, no water was spraying out and dishwasher was making a whirling noise.
    After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.
    • Joe from Arvada, CO
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      More than 2 hours
    • Tools:
      Nutdriver, Pliers, Screw drivers, Wrench set
    • Parts Used:
      5300809909
    1 of 2 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      1 Review
      5.0
      Filter By Rating:
      • 5 Stars
        1
      • 4 Stars
        0
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS452574
          Manufacturer Part Number: 5300809909
          Brand
          Model Number
          Description
          Frigidaire
          1031-005A
          Dishwasher - DISHWASHER
          Kenmore
          58714249990
          Dishwasher
          Kenmore
          5871429990
          Dishwasher
          Kenmore
          5871430591
          Dishwasher
          Kenmore
          5871433590
          Dishwasher
          Kenmore
          5871434969
          Dishwasher
          Kenmore
          5871444990
          Dishwasher
          Kenmore
          5871501190
          Dishwasher
          Kenmore
          5871504190
          Dishwasher
          Kenmore
          5871511590
          Dishwasher
          Kenmore
          5871710591
          Dishwasher
          Kenmore
          58717245990
          Dishwasher
          Kenmore
          5871733590
          Dishwasher
          Kenmore
          5871734569
          Dishwasher
          Kenmore
          58717345691
          Dishwasher
          Kenmore
          58717345790
          Dishwasher
          Kenmore
          5871744590
          Dishwasher
          Frigidaire
          61-1014-00
          Dishwasher - DISHWASHER
          Tappan
          61-1014-10-00
          Dishwasher - 24" Built-in
          Tappan
          61-1021
          Dishwasher - DISHWASHER
          Tappan
          61-1021-10-00
          Dishwasher - 24" Built-in
          Frigidaire
          61-1043-10
          Dishwasher - DISHWASHER
          Tappan
          61-1043-10-00
          Dishwasher - 24" Built-in
          Frigidaire
          61-1073-10
          Dishwasher - DISHWASHER
          Tappan
          61-1073-10-00
          Dishwasher - 24" Built-in
          Frigidaire
          61-1083-10
          Dishwasher - DISHWASHER
          Tappan
          61-1083-10-00
          Dishwasher - 24" Built-in
          Frigidaire
          61-1093-10
          Dishwasher - DISHWASHER
          Tappan
          61-1093-10-00
          Dishwasher - 24" Built-in
          Tappan
          61-1120-00
          Dishwasher - 24" Built-in

          Get in touch, we're here to help!

          Open until 10PM EST

          Contact Customer Service