Motor Shaft Seal Kit 5300809909 | Official Frigidaire Part | Fast Shipping | PartSelect
Motor Shaft Seal Kit – Part Number: 5300809909
( Grid squares measure 1x1 inch )
Motor Shaft Seal Kit – Part Number: 5300809909 Motor Shaft Seal Kit – Part Number: 5300809909 Motor Shaft Seal Kit – Part Number: 5300809909 https://partselectcom.azureedge.net/Schematics/Frigidaire/7SGM81QV.gif

Motor Shaft Seal Kit

PartSelect Number PS452574

Manufacturer Part Number 5300809909

Manufactured by Frigidaire

Product Description

Motor Shaft Seal Kit Specifications

This motor shaft seal kit does not include a macerator blade, but does come with wash and drain impellers(upper and lower).

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Leaking | Not draining

This part works with the following products:

Dishwasher.

This part works with the following brands:

Frigidaire, Tappan, Kenmore, Amana, Gibson, Caloric, Kelvinator, Maytag.

Part # 5300809909 replaces these:

662, 809909, AP2135640.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Customer Repair Stories
Average Repair Rating: 2.1 / 5.0, 2 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Trevor from LOGAN, UT
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Parts Used:
5300809909
Water leaking from motor shaft under dishwasher
DISASSEMBLY
- Switch off circuit breaker for dishwasher.
- Remove lower front covers from washer to observe motor (for later steps) and to clean-up water.
- Remove top and bottom dishracks.
-You may want to take pics of the placement/orientation of components in the following steps as you disassemble them for reference during reassembly.
- Remove spray-arm base from pump housing.
- Remove and discard impeller— put a screwdriver in the impeller grooves to prevent it turning as you loosen the screw.
- Remove impeller, O-ring, and blade. Discard impeller and O-ring, but keep blade (I couldn’t find the O-ring; it had probably disintegrated).
- Remove pump housing, pump plate, and gasket.
- Use two flat-head screwdrivers on opposite sides of the rotor to pry it off the motor shaft. Be cautious not to damage the area around the motor shaft—wood can be used to protect the area and provide better leverage. If the rotor can’t be removed, a chisel or hacksaw can be used to split it before prying it up— be cautious of the motor shaft when splitting the rotor. Discard the rotor.
- Locate the upper seal, note its orientation (cup-side-down), remove it, and discard it (my upper seal was in the recess in the bottom of the rotor).
-Drive the shaft-key (small metal tab) out of the shaft groove using a hammer and flat-head screwdriver and discard it— the new rotor has a molded-in tab that will slide into the groove in place of the shaft-key.
- Remove ceramic ring from motor shaft and discard it (my leak was caused because the ceramic ring was broken in half).
- Use a flat-blade screwdriver to pry loose the lower seal—before removing it from the shaft, note its orientation (wide-side-down). Be caution not to damage the area around the motor shaft—wood may again be used for protection and leverage.

CLEANING/PREP
- Clean shaft with wire brush, white vinegar, and a rag (you may not need the wire brush if the shaft is in good shape, but my motor shaft was heavily corroded/rusted and I needed to smooth it to prevent it damaging the seals). Clean groove in motor shaft with flat-head screwdriver and rag.
- Use a rag and white vinegar to clean motor shaft recess and pump housing seat. The bottom of the motor shaft recess must be clean and smooth for the lower seal to seat properly.
- Clean pump plate, gasket, blade, pump housing, and screws with white vinegar and a plastic-bristled brush.

ASSEMBLY
-Wet new rubber seals, new ceramic ring, and new rotor with water to help them slide into place.
-Refer to pics taken during disassembly as needed for the following steps.
- Place new lower seal (wide-side-down) over motor shaft in bottom of recess.
-Push new upper seal (cup-side-down) into recessed area in the bottom of the new rotor.
-Push new ceramic ring into upper seal (cup-side) in bottom of rotor.
-Align groove on motor shaft with tab in rotor (a mark on the outside of the rotor shows the tab’s location) and seat rotor on the motor shaft by hand. Verify that the motor turns when the rotor is turned by hand. If not, remove the rotor and reposition it so that its tab slides into the groove in the motor shaft.
-Place gasket, pump plate, and pump housing in position. Start pump housing screws, but leave them loose.
- Place blade and new O-ring on rotor.
- Place new impeller on rotor and insert screw. Tighten moderately — overtightening could cause leaks. Hold the impeller by hand to prevent it turning as the screw is tightened— do not use a screwdriver to prevent the impeller turning.
- Finish tightening pump housing screws.
- Seat spray-arm base on pump housing and insert/tighten its mounting screws.
- Switch on circuit breaker for dishwasher.
- Start washer and watch motor to verify that shaft seal is not leaking. Run a full cycle to rinse the new parts and remove debris and vinegar residue. Continue to observe motor shaft area for leaks during cycle.
-Replace lower front covers.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Joe from Arvada, CO
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set
Parts Used:
5300809909
heard a noise while dishwasher was in operation, opened door and noticed the dishes were dry, no water was spraying out and dishwasher was making a whirling noise.
After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.
1 person found this instruction helpful.
Was this instruction helpful to you?
Model Cross Reference

This part works with the following models:

PartSelect Number: PS452574
Manufacturer Part Number: 5300809909
Brand
Model Number
Description
Frigidaire
1031-005A
Dishwasher - DISHWASHER
Kenmore
58714249990
Dishwasher
Kenmore
5871429990
Dishwasher
Kenmore
5871430591
Dishwasher
Kenmore
5871433590
Dishwasher
Kenmore
5871434969
Dishwasher
Kenmore
5871444990
Dishwasher
Kenmore
5871501190
Dishwasher
Kenmore
5871504190
Dishwasher
Kenmore
5871511590
Dishwasher
Kenmore
5871710591
Dishwasher
Kenmore
58717245990
Dishwasher
Kenmore
5871733590
Dishwasher
Kenmore
5871734569
Dishwasher
Kenmore
58717345691
Dishwasher
Kenmore
58717345790
Dishwasher
Kenmore
5871744590
Dishwasher
Frigidaire
61-1014-00
Dishwasher - DISHWASHER
Tappan
61-1014-10-00
Dishwasher - 24" Built-in
Tappan
61-1021
Dishwasher - DISHWASHER
Tappan
61-1021-10-00
Dishwasher - 24" Built-in
Frigidaire
61-1043-10
Dishwasher - DISHWASHER
Tappan
61-1043-10-00
Dishwasher - 24" Built-in
Frigidaire
61-1073-10
Dishwasher - DISHWASHER
Tappan
61-1073-10-00
Dishwasher - 24" Built-in
Frigidaire
61-1083-10
Dishwasher - DISHWASHER
Tappan
61-1083-10-00
Dishwasher - 24" Built-in
Frigidaire
61-1093-10
Dishwasher - DISHWASHER
Tappan
61-1093-10-00
Dishwasher - 24" Built-in
Tappan
61-1120-00
Dishwasher - 24" Built-in