The Oven Bake Element is a black, metal part which supplies heat to the oven. This element is 19-1/2" wide x 18-1/2" long and has 3-1/2" inserts. It is rated as "Easy" to install by users, and attaches to the bottom of the oven. If you notice visible damage, or that your oven is not receiving heat properly then it may be a problem with this part. Check your model number and user manual to see if this is the right part for you. It is important for you to disconnect your appliance from the power source before performing this repair. After disconnecting your appliance, remove the two screws/nuts connecting the old element, pull it out, and discard if faulty. Simply connect the new element prongs where the old element fit, and screw it back in. You may need a flashlight when making this repair.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Range Oven Bake Element
Troubleshooting
This part fixes the following symptoms:
Little to no heat when baking | Element will not heat | Oven not heating evenly | Will Not Start
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Katina M - 13 days ago
Verified Purchase
No Brainer, Money Saver
When my oven wouldn't reach the proper temperature for baking, I immediately searched online for replacement element and found PartSelect. The ordering process from start to finish was a breeze and I had my oven back to peak performance in 4 days!
★★★★★
★★★★★
Ronald C - May 2, 2024
Verified Purchase
Easy Repair
We are an elderly couple and needed our oven. The part was sent out to us within days. I was so pleased. Easy to put on. We now have a working oven.
★★★★★
★★★★★
Barry B - April 27, 2024
Verified Purchase
Simple fix, works great!
This element came exactly as needed, and once installed functioned perfectly.
★★★★★
★★★★★
Deewayne W - April 24, 2024
Verified Purchase
Perfect install
FIRST THING Turn off the 50 amp oven breaker in the electrical panel!!!!! PLEASE!!!!
Then Pull out the Range from the WALL!!! Then. Carefully unplug the range cord from the WALL!!!
Once this is done the appliance is safe to work on!! You TUBE show the simple replace meant. My element wire was short and disappeared in the range so I went to the back of the unit removed the 8 screws on the back of the range then just pushed the element wire back in plugged it on the element tighented the oven side screws up. Then put the back cover back on pulled the oven back in pushed it back to the wall turned the breaker back on turned the oven to Bake 350 then was surprised how FAST it came up to temp!!!! Perfect buy!!!
★★★★★
★★★★★
Michael C - March 1, 2024
Verified Purchase
Over element
Part arrived on time and in perfect condition the video link sent helped greatly with the replacement of the element
★★★★★
★★★★★
Randall P - February 24, 2024
Verified Purchase
Easy repair in minutes. Two wires, two screws...done.
This part was packaged well. Fit great. Up and working.
★★★★★
★★★★★
Zeke C - February 5, 2024
Verified Purchase
Works
Took a few minutes and had it swapped in and been working
★★★★★
★★★★★
Maria B - January 10, 2024
Verified Purchase
Fast shipping!! Part fits and oven working great!
Super fast shipping and part as described. My oven was back working in two days.
★★★★★
★★★★★
Christopher F - December 21, 2023
Verified Purchase
easy repair..part fit nicely
The electrical fittings were at a 90 degree angle to the ones on the oven wiring but I got them connected without much trouble...
..had trouble with the Fed Ex shipper but in the end everything worked out...oven back in service...
★★★★★
★★★★★
Jack P - December 8, 2023
Verified Purchase
Thank you
Fast delivery, works great.
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 303 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Electrical connection pulled off the element
When I pulled the element out of the back panel of the oven to remove it, the electrical connection got caught on the edge of the hole in the panel and disappeared back into the oven insulation. It was difficult to find and pull it back out to reinstall it on the new element.
When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!
Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven) Step 2- remove bakin
... Read moreg racks Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element) Step 4- carefully pull the bake element out until you have the wires through the holes Step 5- carefully pull the bake element from the wire clips on both sides Step 6- take broken element out of over and put new one in Step 7- slide new bake element ends onto wire clips Step 8- slide new bake element and connected wires back though back of oven Step 9- used saved screws to screw metal plates on bake element to the back of the oven Step 10- replace oven racks Step 11- restore power to range Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!
Read less
Meaghan from HOLLY HILL, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
8 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Easy as could be
2 1/4 inch screws and 2 blade connectors fir the power. Took me longer to find my nutdriver than the repair.
Kenny from HENDERSONVLLE, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
7 of 11 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven heat element broke in 1/2.
Took screws out back of oven to get to connectors . Pulled old conectors off Installed new element took about 5 min. Very easy job. Also good time to clean oven .
Keith from LAKEVILLE, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
6 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element burned out.
Turned off power at the circuit box. After locating 1/4" nut driver (the hardest part of the repair)I removed the oven racks. Took the opportunity to wipe out oven. Removed the two screws holding the element in place.Pulled element out gently to expose the connections. Wiggled the terminal connector off the terminal on element. Gave the w
... Read moreire a little bend to keep it from pulling back into frame. Repeated process on other side. Removed new element from wrapper. Placed element on oven floor, reattached terminals--making sure they were on snuggly--carefully slid terminal ends back though slots in oven body. Lined up brackets, reinstalled screws, replaced racks and turned power back on. Turned oven on it worked. Made cookies! Very easy repair.
Read less
Pamela from FRIDLEY, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
5 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom burner wouldn’t heat
Watched the video
cynthia from SEBRING, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)
5 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
element burnt out
purchased a square bit and removed screws easily and disconnected it from the wiring and pushed in the new element secured screw and it was back to baking.
Demoris from GOLDSBORO, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the old bake element was corroded and non-funtional
Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the
... Read more oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.
Read less
Stephen from RONAN, MT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
4 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element went out
The broil element and range were both working so I removed the bake element to test for continuity. Use a 1/4” socket or wrench to remove the two screws holding the bake element to the rear wall of the inside of the oven. Pull the ends of the element out of their recesses taking care not to lose a wire inside the back panel of the oven. P
... Read moreull the wires off the element ends. You should be able to do this by hand; use a flathead screwdriver for a little prying if necessary. Visually inspect the element for physical damage. If you don’t see any, test the element with an ohmmeter or multimeter. If it reads anything other than 0 ohms (continuity), your element is defective. Installation process is reverse of removal.
Read less
Nicholas from COTTONDALE, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
4 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
71 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
William
January 2, 2019
I think it would be good to tell people to make sure the power is off
Hi William, thank you for contacting us. Yes, it is always best that before doing any repair you make sure your appliance is not connected to power so that you do not harm yourself or break something else on the appliance. Have a great day.
66 people found this helpful.
Was this helpful?
Thank you for voting!
Maureen
March 28, 2019
How to install heating element in bottom of oven?
For model number 79096010407
Hello Maureen, Thank you for the question. Here is a link to a How To video that may help. Good luck with the repair!
https://www.youtube.com/watch?v=1E0VmuFtfXM
38 people found this helpful.
Was this helpful?
Thank you for voting!
Dustin
May 14, 2019
If my bottom heating element is broken can it cause the top part of the stove to not hear correctly
For model number TEF361GSB
Hello Dustin, thank you for your question. No, any oven issues shouldn't cause the top burners to be affected. The top burners are controlled by burner switches behind the temperature knobs and the oven control board and oven sensor control the oven elements and heating. I hope this helps.
19 people found this helpful.
Was this helpful?
Thank you for voting!
Ralph
May 22, 2019
Can you use the broil element for the bake element cause i don't use the broiler at al so would it work
For model number FEF326ABM
Hello Ralph, thank you for your question. Unfortunately, the broil element will not work for the bake element. To replace the bake element you would have to purchase PartSelect Number: PS438018. I hope this helps!
13 people found this helpful.
Was this helpful?
Thank you for voting!
Betty Justice
February 25, 2019
My bottom element heats fine. Since i purchased a new element some time back i have smut on my lower part of oven and on the element every time i cook something. I do not know what causes it. Will a new element help? Thank you.
For model number FEFL64FSD
Hello Betty, Thank you for contacting us. It is possible that the bake element is faulty. I suggest checking it with a multimeter. You should get a reading between 0-50 ohms. Good luck with your repair!
12 people found this helpful.
Was this helpful?
Thank you for voting!
Betty
February 6, 2019
Frigidaire oven element quick heating, so i know it needs to be replaced. My question is: Do i have the right model number to order a new one?
For model number FEF366EBE oven heat element
Hello Betty, Thank you for contacting us. After reviewing your model number I show PS438018 is the part number for the bake element for this model. Good luck with your repair!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Vanessa
May 29, 2019
My oven has a new bottom element but it still won't heat up
Hello Vanessa, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Darlene
April 12, 2019
Does this part work with this model
For model number FEF352AWE
Hello Darlene, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS438018. Thank you for your inquiry, good luck with this repair!
8 people found this helpful.
Was this helpful?
Thank you for voting!
John
June 6, 2019
I need both top and bottom elements bottom element is 15 inches long
For model number vf91725643
Hello John, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. vf91725643 looks to be a serial number. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Amy
April 1, 2019
Will this particular element work
For model number FFEF3003NWA
Hello Amy, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS438018. Thank you for your inquiry, good luck with this repair!
6 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Range","title":"Range","url":"/Range-Parts.htm"},{"position":2,"name":"Element or Burner","title":"Element or Burner","url":"/Range-Elements-and-Burners.htm"},{"position":3,"name":"316075103","title":"316075103","url":""}]
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
