Frigidaire/Frigidaire_Thumb/ZMRPSEM2.gif
See part 22 in the diagram
Replacing your Frigidaire Refrigerator Hinge Bearing play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Hinge Bearing

★★★★★
★★★★★
27 Reviews

Rated by 77 customers 

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your 25344352403!
 Fits your 25344352403!
PartSelect Number PS429803
Manufacturer Part Number 240328201
Manufactured by Frigidaire
You May Also Need?
Product Description

Hinge Bearing Specifications

Sold individually. Also known as a short door closing cam.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Clicking sound | Door won’t open or close | Noisy | Door Sweating
This part works with the following products:
Refrigerator.
This part works with the following products:
Frigidaire, Kenmore, Westinghouse, Gibson.
Part# 240328201 replaces these:
AP2115808, 891001, 240328201, 240561601
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

3 questions answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brian
September 19, 2017
Refrigerator door closes approximately three quarters of the way on its own. The last quarter requires light manual effort to complete the closing. Also the door alignment dropped approximately 1/8 inch. What parts need to be replaced.
For model number FRS6R4EW2
Hi Brian, Thank you for your question. You would have to take a look at your bearings and hinges. Those would be the most likely parts that would be causing an issue like that. Good luck with your repair.

11 people found this helpful.

Was this helpful?
Thank you for voting!
Harry
June 20, 2019
What grease do you use on the door closing cam? Can you please post the name and brand? I cannot seem to find anything. Thanks
For model number FRS3R4EWA
Hi Harry, Thank you for your question. There is no grease that you would use for the door cams. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Mike
February 5, 2020
Does this part work with fridge model number PLHS280ZAB5?
For model number PLHS280ZAB5
Hello Mike, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS429803. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Part Videos

Replacing your Frigidaire Refrigerator Hinge Bearing

Replacing your Frigidaire Refrigerator Hinge Bearing play video
Customer Repair Stories
 Average Repair Rating: 4.4 / 5.0, 77 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
The ice dispenser would only dispense crushed ice, Fridge door cluncked when opening and closing
For the ice dispenser, I read a blog that pointed me right to the solenoid that controls the linkage for the crushed /cubed ice.I first unplugged the fridge. Then removed the ice maker basket. Removed 2 ea screws from each side of the supports of the lower brackets. Then lifted the tray assy off the mounting bracket, moving the front of the bracket down you can then unhook the power/control connector.
The tray then comes right out. Once out you remove two screws that hold a plastic plate on. With this removed you can see the solenoid that actuates the linkage for the ice cube and crushed ice. You then remove 2 ea machine screws that hold the solenoid in. Remove grd. wire. and pull power wires off tabs. You can then remove the solenoid by sliding it out of the plastic retainer. With it out you install the new plunger and reassemble in the reverse order. 15 mins tops.

The main Refidgerator door, made a cluncking sound. Lube didn't help. I removed the door by removing the top screw from the plastic cover, then slide it forward, then remove the two screws that hold the hinge on and then lifting the door off, once off the lower nylon hinge bearing comes right out of the door, the plate is removed with a screw driver. Installed in reverse order and cluncking was gone. 10 mins
Other Parts Used:
Refrigerator Ice Dispenser Solenoid Door Closing Cam
  • Al from Shakopee, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
110 of 127 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Nylon door hinge bearing on the bottom of refrigerator door broke
First I removed the contents from the door. Second, I removed the exposed bolt on the top hinge(per the manual instructions) and then I removed the plastic hinge cover. Up next was to remove the remaining two bolts from the top hinge. I should, at this point, say it is much easier to have someone help steady the door for you so it doesn't fall off the refrigerator. Now remove the door and the old nylon bearing. Replace with the new bearing and replace the door. This repair couldn't have been easier.
Other Parts Used:
Door Closing Cam
  • Steve from Ankeny, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
61 of 64 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud thump/cracking noise when opening door.
Upright refrigerator/freezer. Damage was on refrigerator side door- lower hinge. Removed everything from inside fridge door. Removed plastic protector plate on top of door hinge with phillips screwdriver. Pulled out top hinge and removed door. Undid two small screws holding bottom bearing hinge bracket. Took out chewed up old bearing hinge. Cleaned bracket of debris. Attached bracket with screws. Inserted new bearing hinge. Put door back on fridge, re-attached top hinge and protective cap. (Still trying not to cringe out of habit when opening the door)
  • Robert from Sarasota, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
49 of 51 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Actuator broken, Door Closing Cam, Door Closure/Hinge Bearing
Unplug refrigerator. Take out spill tray by sliding out. remove bottom 3 screws, gently but firmly push up and against refrigerator(Top section of cover snaps in by pulling cover down while holding cover against refrigerator). There is a ribbon wire connecting the two boards, care not to tear it out of connectors. There are two tabs on the plastic connector holding the ribbon wire to the outside board,pull the tabs out a little and gently pull the ribbon loose, carefully. There are 3 screws holding in the back board, remove them, them remove water hose from water actuator so the assembly can come out. Gently spread the plastic holder to be able to take the broken paddle out. Watch closely how the third arm on the actuator(Lower left arm)is resting on the back of the flapper.Replace the Actuator exactly the same. Just reverse the steps to install the rest of the parts.(Had a time getting the water hose back into it place. I used pliers to push and wiggle it back into it opening).Don't forget to plug the frig back in again. DOOR CLOSING CAM AND HINGE BEARING ARE VERY EASY. It take about 10 to 15 minutes to do. Empty door drawers before procedure the screw holding the plastic cover, remove cover. I used a 3/8" nut driver and my cordless drill to take out the two lag bolts holding the top hinge.Lift door off bottom hinge. Replace Door Closure/Hinge Bearing. Reverse procedure to finish installation.
Other Parts Used:
Ice Actuator Door Closing Cam
  • Ken from Diamond springs, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
15 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrig door would not close automatically
Replaced the plastic/nylon piece on the door. First, I remove the door hinge cover by unscrewing the one bolt. Second, unbolted the two bolts that hold the door in place. Third, lifted the door off the bottom hinge. Four, remove the bottom plate that is held in place by 3 screws. Five, using pliers move the old plastic piece from the bottom of the door. Six, press into place the replacement part. Seven, re-install the bottom plate. Eight, rehang the door on the bottom hinge. Nine, restall the top hinge and rebolt the two bolts that hold the hinge in place. Ten, reinstall the top cover. Finished.
  • Michael from Lithia, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
14 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not shut properly
Removed the door and installed ne bushing on bottom of hinge
Other Parts Used:
Door Closing Cam
  • Matthew from Parker, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
when opening door you would hear a loud thump.
Removed stuff on door, removed 2 screws on top of door, lifted door off replaced one door closure/hinge bearing and one door closing plate and put door back on and wala no more thump.
Other Parts Used:
Door Closing Cam
  • James from Palm City, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
12 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The main Refidgerator door, made a cluncking sound
I removed the door by removing the top screw from the plastic cover, then slide it forward, then remove the two screws that hold the hinge on and then lifting the door off, once off the lower nylon hinge bearing comes right out of the door, the plate is removed with a screw driver. Installed in reverse order and cluncking was gone. 15 mins
Other Parts Used:
Hinge Bearing
  • Richard from Dunlap, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
12 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door was making a popping noise when you opened the door.
First I removed the door. Took off the broken parts and replaced them. Easy and fast to repair.
Other Parts Used:
Door Closing Cam Hinge Bearing Closer - Freezer
  • Judy from Visalia, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
10 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hinge Bearing shattered, and door shelf broke
Removed the top hinge from the door, removed the door, removed the doorstop and remains of the old bearing, and then replaced the items with the new ones in the reverse order. The screw I purchased was not needed.

The shelf had been broken for a while, and just needed to be slipped into the existing slots on the door
Other Parts Used:
Door Stop SCREW Door Shelf
  • Chris from Bakersfield, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
27 Reviews
4.9
Filter By Rating:
  • 5 Stars
    25
  • 4 Stars
    1
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS429803
Manufacturer Part Number: 240328201
Brand
Model Number
Description
Kenmore
25344302400
Refrigerator
Kenmore
25344302401
Refrigerator
Kenmore
25344304400
Refrigerator
Kenmore
25344304401
Refrigerator
Kenmore
25344333600
Refrigerator
Kenmore
25344333601
Refrigerator
Kenmore
25344333602
Refrigerator
Kenmore
25344333603
Refrigerator
Kenmore
25344333604
Refrigerator
Kenmore
25344333605
Refrigerator
Kenmore
25344333606
Refrigerator
Kenmore
25344333607
Refrigerator
Kenmore
25344333608
Refrigerator
Kenmore
25344333609
Refrigerator
Kenmore
2534433360A
Refrigerator
Kenmore
25344352400
Refrigerator
Kenmore
25344352401
Refrigerator
Kenmore
25344352403
Refrigerator
Kenmore
25344352404
Refrigerator
Kenmore
25344352405
Refrigerator
Kenmore
25344352406
Refrigerator
Kenmore
25344352407
Refrigerator
Kenmore
25344352408
Refrigerator
Kenmore
25344352409
Refrigerator
Kenmore
25344353401
Refrigerator
Kenmore
25344353403
Refrigerator
Kenmore
25344354400
Refrigerator
Kenmore
25344354401
Refrigerator
Kenmore
25344354403
Refrigerator
Kenmore
25344354404
Refrigerator

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service