( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Range Oven Temperature Sensor DG32-00002B

 Fits your NE59M4320SG!
★★★★★
★★★★★
6 Reviews

Rated by 2 customers 

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.

$ 130.30
  On Order
 Fits your NE59M4320SG!
PartSelect Number PS4240743
Manufacturer Part Number DG32-00002B
Manufactured by Samsung for Samsung
Product Description

Range Oven Temperature Sensor Specifications

This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will not start or has too little or too much heat, it is likely that the temperature sensor is bad, or defective. This temperature sensor features a 3.9-inch-long probe, 3.2-inch-long wire harness, and 1.7-inch-wide support bracket. Replacing this sensor is fairly simple but will require a screwdriver, wrench and drill with the appropriate Philips-head bit. Disconnect your range from the wall outlet and pull it out from the wall. Removing your range door is not necessary, but will make removing the sensor that much easier. You will now locate your temperature sensor, which will likely be near the heating element at the top/bottom of the oven. Remove any securing screws holding the heating element and/or sensor in place. At the rear of the range, disconnect and remove the rear panel to gain access to the electronics of the range. Disengage the sensor and its locking tabs, and may also require you to disconnect the terminals for the heating element if your temperature sensor is fastened to it. Remove the sensor and heating element (if necessary). If the sensor is connected to the heating element, use a wrench to unfasten it. Now you install the new temperature sensor and reassemble your oven, ensuring that wire terminals are connected correctly.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Samsung Range Range Oven Temperature Sensor

Replacing your Samsung Range Range Oven Temperature Sensor
Troubleshooting
This part fixes the following symptoms:
Little to no heat when baking
This part works with the following products:
Range, Microwave Oven Combo, Wall Oven.
Part# DG32-00002B replaces these:
AP4343210, DG32-00002A
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
6 Reviews
4.8
Filter By Rating:
  • 5 Stars
    5
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 4.4 / 5.0, 2 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
oven will not come to desired temp setting
ordered the temp sensor for a standard complaint, new sensor was the correct part ordered, however, once the old sensor was removed, I ohm'd the original and the new part. Both were 1080, checked wiring, checked gas burner, checked line voltage. Searched other part prices, found Samsung to be a not desirable product to own. This non repair was to help my neighbor who lives on a fixed income. Checked oven temp with the oven at 350 f setting, oven was 223 f. Set oven to 465 f and fount the oven at 353 f. I wanted to return the part but she insisted I install it anyway and found the oven doing the same thing. She did not want to throw more money at a 4 year old range. Will use it as it is but will buy a cheap oven temp gauge. Samsung sucks.
  • DAVID from BIRDSBORO, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat consistently
My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the issue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG!
  • Steven from CHEYENNE, WY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
12 of 27 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

29 questions answered by our experts.
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
DM
November 11, 2017
When I set oven to preheat 350, the digital display registers 350 and beeps signaling preheat temperature has been reached, however, oven internal temperature is only 125-150. Continuity is good on the bake element, I’m thinking sensor (thermistor ftq386). I’d appreciate your thoughts. Thanks
For model number FER300SW
PartSelect logo
Hi DM, Thank you for the question. I suggest testing the oven sensor.Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!

22 people found this helpful.

Was this helpful?
Thank you for voting!
Jaime
November 28, 2017
My oven does not heat up past 240 degrees. For the last few months my oven has been taking 30-35 or longer to reach the required temp.
For model number nx58h5600ss
PartSelect logo
Hi Jaime, Thank you for your inquiry. If the oven is taking a long time to heat then you will need to check the sensor. I hope this helps. Thank you and have a great day!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Terry
December 11, 2018
Control panel (touch pad) unable to use any of the functions push them but nothing happens. The screen shows se tried unplugging for 30 seconds or longer with no results.
For model number NX583GOVBSR
PartSelect logo
Hello Terry, thank you for your question. The SE code is in relation to a shorted, or stuck touch panel key. Open the control console and make sure that the wire harness is plugged into the oven electronic control board properly. Check the wire harness for damage. If the wire harness is okay, replace the control panel. If the problem persists, replace the electronic control board. I hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Steve
January 14, 2018
I tested the sensor-thermistor and it reads 1078 ohms. Is that acceptable? I saw a post that it should be between 1080-1090 when the digital read out by the buttons says it is at 350 it really was only 240 inside and after checking it every 20 min for over an hour the hottest it got was 345. 20 min after the oven said it was at the 350 temp the temp gauge i put inside only says 325. 20 min later it was at 345 and 20 min after that it was at 345 still
For model number NX583G0VBBB
PartSelect logo
Hello Steve, Thank you for your inquiry. If the sensor was tested at room temperature, then yes 1078 ohms is acceptable. I would advise you to check your control board as well. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Larry
March 7, 2018
After the self clean, the oven door will not unlock, have tried all the suggested remedies. Would this be a thermo-sensor issue?
For model number NX58F5500SS
PartSelect logo
Hello Larry, thank you for your question. If the door will not unlock at the end of the clean cycle then you may have a problem with the oven temperature sensor. Most electronic control ovens will display a fault code to indicate that the sensor has failed. If you suspect that the sensor is at fault, you should first remove the power to the oven for a few moments and then reconnect. This may reset the control and allow you to unlock the door. If you still cannot unlock the door, then you can check the oven temperature sensor from the back of the unit. Remove power again and also remove the back panel. Locate the oven temperature sensor wire harness connector and unplug. You can check the resistance of the sensor with a multi-meter. If the sensor has failed, you can connect a new one to the harness connector temporarily, reconnect power and operate the door unlock function. With the door open you can then replace the sensor. If the sensor is tested and is not faulty, the issue is most likely the door lock mechanism itself. If you suspect that the door lock/motor assembly is at fault then you will need to unlock the door manually. The assembly is normally located between the main top and the oven and can only be accessed by raising the main top. This is very difficult to do because the screws that hold the top in place are inaccessible with the door closed. If the assembly cannot be accessed then you will have to form a wire hook,(coat hanger) and insert it between the door and the latch and manually pull the latch to the open position. Remove power to the oven before attempting this procedure and be careful not to damage the finish. I hope this information helps. Good luck with your repair!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Bill
January 31, 2019
The oven gets hot quickly and goes way over the temperature requested. Can't bake anything. Preheated oven at 175 and it went to way over 400 in less than 5 minutes. What part do i need to order please.
For model number Samsung NE59J7630SG
PartSelect logo
Hello, thank you for your question! Most often when an oven is heating far past what it should be, it is an indication of a faulty oven sensor, or thermistor. We would recommend testing that for proper continuity with a multimeter. If that is testing properly, we recommend checking your elements to ensure there is no damage to them, as that can occasionally cause the part to malfunction and heat higher than intended. We hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Danae
December 18, 2017
My gas range's oven will not turn on. The broiler works tho. How to test oven tmp controller?
For model number NX58H9500WS
PartSelect logo
Hi Danae, Thank you for your question. In order to test the oven temperature control, you will need to use a multimeter. If you are unfamiliar with a multimeter, there are videos on YouTube that you can reference on how to use one. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Jean
December 1, 2022
Our dual oven lower oven is heating to specified temperature, but the top oven is consistently heating 75-100 degrees below specified temp. How can this happen and are there 2 oven thermometers or one?
For model number NE59J7850
PartSelect logo
Hi Jean, thank you for reaching out. There are two temperature sensors in your model. You need to check the following parts to fix the issue: Broil Element, part number PS11720673, and Temperature Sensors, part numbers PS4240744 and PS4240743. We hope this information helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Chris
January 5, 2022
I see the ignitor glow. I hear the oven ignite. I few seconds later burner goes off and ignitor is not glowing. It is cycling constantly.
For model number NX58H9500
PartSelect logo
Hello Chris, thank you for your question. A few things could cause this issue. A malfunctioning flame sensor will not detect the flame, and so will not open the gas line to keep the burner going. A partial blockage in the gas line may allow the burner to light but will not provide enough fuel to keep it lit. Also, if your pressure switch detects that your system venting pressure is off, it will shut down your heating system to prevent it from venting poisonous gas into your home. We recommend contacting a professional to inspect your gas line. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Rita
January 28, 2019
Our oven sometimes starts up with a loud whoosh, we smell gas when that happens. Once the oven reaches temperature, the igniter cycles off after about 10 minutes at correct temperature (assume normal). However, when igniter cycles back on, the oven does not re-heat, despite the igniter staying on; the temperature drops and the smell of gas persists until we shut oven off.
For model number NX58H5600SS
PartSelect logo
Hello Rita, Thank you for your question. I suggest to check the following parts: PS4241428 Oven Burner Igniter and PS4241390 Assembly VALVE-SAFETY;FX710B. I hope this helps! Have a nice day.

1 person found this helpful.

Was this helpful?
Thank you for voting!
  • 1
  • 2
  • 3
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS4240743
Manufacturer Part Number: DG32-00002B
Brand
Model Number
Description
Samsung
AA
Range - Samsung Range/Stove/Oven Nx60a6511sg Aa
Samsung
FCQ321HSUW
Range - Samsung Range/Stove/Oven Model FCQ321HSUW Parts
Samsung
FCQ321HSUWXAC
Range - Samsung Range/Stove/Oven Model FCQ321HSUWXAC Parts
Samsung
FCQ321HSUX
Range - Samsung Range/Stove/Oven Model FCQ321HSUX/XAA-0000 (FCQ321HSUX/XAA0000, FCQ321HSUX/XAA 0000) Parts
Samsung
FCQ321HTUB
Range - ELECTRIC RANGE
Samsung
FCQ321HTUB/XAA-0000
Range
Samsung
FCQ321HTUBXAA
Range - Samsung Range/Stove/Oven Model FCQ321HTUBXAA Parts
Samsung
FCQ321HTUW
Range - ELECTRIC RANGE
Samsung
FCQ321HTUW/XAA-0000
Range
Samsung
FCQ321HTUWXAA
Range - Samsung Range/Stove/Oven Model FCQ321HTUWXAA Parts
Samsung
FCQ321HTUX
Range - ELECTRIC RANGE
Samsung
FCQ321HTUX/XAA-0000
Range
Samsung
FCQ321HTUXXAA
Range - Samsung Range/Stove/Oven Model FCQ321HTUXXAA Parts
Samsung
FE-N500WX
Range - ELECTRIC RANGE
Samsung
FE-N500WX/XAA-0000
Range
Samsung
FE710DRS
Range - ELECTRIC RANGE
Samsung
FE710DRS/XAA-0001
Range
Samsung
FE710DRSXAA
Microwave Oven Combo - Samsung Oven/Microwave Combo Model FE710DRSXAA Parts
Samsung
FEN300WX
Range - Samsung Range/Stove/Oven Model FEN300WX Parts
Samsung
FEN300WXXAA
Range - Samsung Range/Stove/Oven Model FEN300WXXAA Parts
Samsung
FEN500WX
Range - Samsung Range/Stove/Oven Fen500wx
Samsung
FEN500WXXAA
Range - Samsung Range/Stove/Oven Model FEN500WXXAA Parts
Samsung
FER300SB
Range - RANGE
Samsung
FER300SB/XAA-0000
Range
Samsung
FER300SB/XAB
Range
Samsung
FER300SBXAA
Range - Samsung Range/Stove/Oven Model FER300SBXAA Parts
Samsung
FER300SW
Range - RANGE
Samsung
FER300SW/XAA-0000
Range
Samsung
FER300SW/XAC
Range
Samsung
FER300SWXAA
Range - Samsung Range/Stove/Oven Model FER300SWXAA Parts
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service