Quick Question!

Have you ever purchased from PartSelect.com before?

417323-1-S-Frigidaire-131268300         -Single Shock Mounting Pin
417323-1-S-Frigidaire-131268300         -Single Shock Mounting Pin 417323-2-S-Frigidaire-131268300         -Single Shock Mounting Pin 417323-3-S-Frigidaire-131268300         -Single Shock Mounting Pin https://www.partselect.com/Schematics/Frigidaire/SY9CMZMG.gif

Single Shock Mounting Pin

Your Price

Order within the next 1 hr and 42 mins and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS417323
Manufacturer Part Number 131268300
Manufactured by Frigidaire

This part works with the following brands: Frigidaire, Kenmore, Crosley, Electrolux, Gibson, Westinghouse.

This part works with the following products: Washer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Shakes and moves.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Shock Absorber Kit

Part Number 3508101

This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. These shock absorbers keep your front-load washer from shaking vigorously by absorbing and reducing vibrations from the wash and spin cycles of your appliance. This kit comes with two shock absorbers because it is recommended to replace both at the same time, as they wear at the same rate. To access your washer shock absorbers, simply remove the lower access panel after disconnecting the power to the appliance.

Order within the next 1 hr and 42 mins and your part ships today!
In Stock

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.6 / 5.0, 2 reviews What's this?
1-2 of 2

42 of 54 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Richard from Quincy, MA

Originall shock was broken

disconnected the power and water supply.

removed the back panel.

unscrewed the contol board that blocked access to the bottom of the shock absorber.

pulled the original pins out with pliers while pressing in the piece that prevents it from working its way out.

removed the shock absorber.

placed the new shock absorber in the bottom mount, put soap on the pin for lubrication and pushed it through the hole. Put the top of the shock absorber in its place and placed the other pin in.

replaced the control board and replaced the rear panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

27 of 31 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: marcia from Holden, MA

Washing tub had broken away fm 3 of 4 supports

disconnected fm water supply and electrical ckt
move washer fm beneath dryer (stacking config.)
removed back, found 2 broken shocks (round type) and 1 broken spring (left looking from back). checked online for parts and found your site. ordered and waited a few days.

back on task, removed controls (lower left corner) to reach pins, removed front lower panel, removed pins and broken remains of both shocks. removed broken spring. left remaining spring to keep tub suspended.

back on task when parts arrived. installed shocks --note that it was not clear that there are 2 shocks in each package (so i order 2 pkgs and now have 2 extra shocks --for next time it breaks away ;-)

crafted a 'hanger' with 10ga wire and 2x4 to permit tub to be supported and/or suspended without unduly stressing new components. attached both shocks being careful to follow instructions about alternating direction and orientation in relation to plastic bushing on the shock mounting points. removed remaining spring and used short length of 10ga wire to pull spring into position and lock.

re-assembled back and front cover... re-attached control circuit. moved closer to water and electrical supply and tested through 2 cycles --no problems found.

put back into position and leveled and locked.

works fine now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-2 of 2

Model Cross Reference

This part works with the following models:

PartSelect Number: PS417323
Manufacturer Part Number: 131268300
Brand Model Number Description
Frigidaire41739012890Washer - Stackable