Part Location Diagram of 131219900 Frigidaire FILTER
See part 17 in the diagram
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

FILTER 131219900

 Fits your 41790807990!

Rated by 1 customer 

Really Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 58.85
  Special Order
Get FREE EconoShip on orders over $100! T&C apply
 Fits your 41790807990!
PartSelect Number PS417185
Manufacturer Part Number 131219900
Manufactured by Frigidaire
Troubleshooting
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Gibson.
Part# 131219900 replaces these:
AP2106321, 406763
Back to Top
Customer Repair Stories
 Average Repair Rating: 3.3 / 5.0, 1 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
The primary problem was that the tub seal assembly was leaking.
1. I began by removing the two screws that hold the front panel in place. I then lifted the top free of the front panel and tilted it back to get it out of the way.

2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.

3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.

4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.

5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.

6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.

The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy.
Other Parts Used:
Tub Seal Assembly Tension Idler Pulley TRUNNION FILTER
  • Rick from Walkerton, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
253 of 318 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Julie
February 13, 2024
Do I need to manually clean the filter. And where is it on this machine?
For model number GWS645RBS3
PartSelect logo
Hello Julie, Thank you for writing. Normally the filter is self cleaning, however over time there can be a build up. To access the filter you will need to remove the inner tub. Thank you for reaching out!

Was this helpful?
Thank you for voting!
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS417185
Manufacturer Part Number: 131219900
Brand
Model Number
Description
Kenmore
41790802990
Washer Dryer Combo
Kenmore
41790807990
Washer Dryer Combo
Kenmore
41790812990
Washer Dryer Combo
Kenmore
41790817990
Washer Dryer Combo
Kenmore
41790862990
Washer Dryer Combo
Kenmore
41790872990
Washer Dryer Combo
Kenmore
41797802790
Washer Dryer Combo
Kenmore
41797802791
Washer Dryer Combo
Kenmore
41797802792
Washer Dryer Combo
Kenmore
41797804790
Washer Dryer Combo
Kenmore
41797804791
Washer Dryer Combo
Kenmore
41797804792
Washer Dryer Combo
Kenmore
41797862790
Washer Dryer Combo
Kenmore
41797862791
Washer Dryer Combo
Kenmore
41797862792
Washer Dryer Combo
Kenmore
41797864790
Washer Dryer Combo
Kenmore
41797864791
Washer Dryer Combo
Kenmore
41797864792
Washer Dryer Combo
Kenmore
41798802890
Washer Dryer Combo
Kenmore
41798802891
Washer Dryer Combo
Kenmore
41798804890
Washer Dryer Combo
Kenmore
41798804891
Washer Dryer Combo
Kenmore
41798862890
Washer Dryer Combo
Kenmore
41798862891
Washer Dryer Combo
Kenmore
41798864890
Washer Dryer Combo
Kenmore
41798864891
Washer Dryer Combo
Kenmore
4179968020
Washer Dryer Combo
Kenmore
41799680210
Washer Dryer Combo
Kenmore
41799680400
Washer Dryer Combo
Kenmore
41799680410
Washer Dryer Combo
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service