This is the drive gear kit for the ram that compacts the trash inside your compactor. If your compactor ram is getting stuck, there is excess noise during its cycle, or if your compactor does not stop at the end of its cycle, the driving gear may be the issue. The gear is white, plastic and approximately 4.5 inches in diameter. This drive gear kit includes both gears, pin spring, retaining clip (c-ring), ram stop, ram cam, and instructions. Make sure to disconnect the power to your trash compactor before beginning the repair.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Compactor ram gets stuck | Noisy | Doesn’t stop at end of compacting cycle | Won’t start
This part works with the following products:
Trash Compactor.
This part works with the following products:
Whirlpool, Kenmore, KitchenAid, Jenn-Air.
Part# 882699 replaces these:
AP3122987, 735285, 882699, 14211018, 41001084, 4149667, 4154800, 4163381, 4163385, 7-49046, 7-49052, 7-49130, 7-76839, 7-77124, 749046, 749052, 749130, 776839, 777103, 777124
...
Show more, 882699, W10451279, Y4149667, Y776839, Y777124
Show less
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Victor
May 29, 2019
Your youtube video shows several parts in the drive gear kit but the picture for part #882699 only shows the main drive gear. Do the other parts such as the mother gear, retainer clip, washers, ram stops and pin come in the kit as well?
For model number GX900QPLB0
Hello Victor, Thank you for the question. This drive gear kit includes both gears, pin spring, retaining clip (c-ring), ram stop, ram cam, and instructions. Thank you for your inquiry, good luck with this repair!
12 people found this helpful.
Was this helpful?
Thank you for voting!
Al
May 21, 2019
My drive gear wheel is dwg4149668. Will this gear replace my broken gear.
Hello Al, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Rod
February 10, 2022
Compactor won’t automatically return after compacting . Must press off to complete cycle. Gear drive ok
For model number GC900QPHBO
Hello Rod, thank you for writing. We have researched the model you have provided and have found the part you are looking for is the Directional Switch PartSelect Number PS11744742. The function of the directional switch on your trash compactor is to ensure the ram lowers to compress your trash, then returns to the top position. If your trash compactor does not complete this task, will not stop at the end of the compacting cycle, or is noisy during operation, you may need to replace the directional switch. We hope to hear from you soon.
Ram always goes down and up ok. At end of return to up cycle it frequently runs and pounds/shakes machine several times before it stops. This all started when the foot treadle start switch acted up. Repaired and replaced the metal piece attached to treadle and which contacts the start button on frame of machine at bottom.
For model number kucs03ftss0
Hello Ken, Thank you for contacting us. I suggest checking the Directional Switch, PartSelect Number PS11744742 with a multi meter and check for continuity. You can also check the Drive Gear Kit for wear or damage. Hope this helps!
Our part number in the big gear is 4149668, 4149667 is listed, will the repair kit work for the 4149668
Hello Sharon, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. We are looking forward to hearing from you!
Was this helpful?
Thank you for voting!
David
November 6, 2021
Will this gear fit whirlpool model GX900QPPS4?
For model number GX900QPPS4
Hello David, Thank you for your inquiry. We have researched the model number you have provided and and show that this part is listed as compatible to your model. We hope this helps.
Was this helpful?
Thank you for voting!
Maurice
December 23, 2021
Broken start knob
For model number Tc407w6
Hello Maurice, thank you for your question. The knob is listed on our site as Key PartSelect Number PS386676. We hope this helps.
Was this helpful?
Thank you for voting!
Timothy
November 22, 2022
We start the compactor and it goes down but then starts grinding when its operating and won't stop unless you turn it off and then back on. Then it will return to the top. Replaced gear a year ago but it seems wobbly. Not sure if that's the problem though after seeing something about a reverse switch.
For model number 13619101
Hello Timothy, thank you for contacting us. The issue is most probably related to the directional switch, part number PS11744742, the rotary switch, part number PS382679, and the drive gear kit, part number PS398589. Please reach out to customer service if you need help placing an order. Glad to be of help!
Is part # PS398589 for Manufacturer # 882699
Jenn-Air Trash Compacter in stock? If not, how long is the backorder?
For model number TC50781
Hello Gregg, Thank you for the question. According to the Website Availability, this is a On Order part. This means we do not currently have the part in stock and waiting on a shipment from. As long as Jenn-Air has stock ready to ship, this takes about 10-15 Business Days for the part to arrive at the Warehouse and approximately 3-7 business days to ship out and arrive to you. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 27 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Compactor stuck in lower position
Moved the compactor out from under cabinet and unplugged the powercable.Laid compactor over on its side Removed the top (4 screws) and base plate (3 screws) as well as the coverplate for the motor(3 screws)Found that large drive was broken in half. Used two screwdrivers to start split ring then pliers to pull it off the rest of the way. Removed the drive gear and the washer. Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked.
Trash compactor started making "bumping" sounds when the RAM went through a cycle and tried to come back up. Finally, one day heard a "pop" went the RAM traveled to the bottom. The gear broke in half. Purchased the gear parts "KIT" online and repair took 15 minutes. Easy to do. Unfortunately, this was not only problem. The "cause" of the gear breaking was the Momentary Start/Stop Switch was bad. It's failure led to the main switch not working. The unit could not tell when the RAM had reached the top of it's cycle. The other problem was that I didn't put trash in the compactor. Suggest HIGHLY to never operate the unit's RAM mechanism without the compactor being at least 1/2 full per the instruction manual. Running it empty can cause a major problem, such as the gear breaking/stripping.
Matt from Houston, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set
21 of 21 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Large Drive Gear Failure (split in half)
Moved the compactor out from under cabinet, laid it on it's side, removed bottom casing (two nuts front, three back), remove compression pin from small drive gear shart, replace new small drive gear and install compression pin, loosen motor mounts to allow large gear replacement, remove circlip holding large drive gear to shaft, remove and repace damaged gear, set gear clearance and tighten motor mounts, grease gears, replace bottom casing. .
Mark from Littleton, CO
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Socket set
17 of 19 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive Gear Broken
Replaced the gear and unit worked execpt the plunger hit the side of the garbage container. This appears the be the reason the gear broke in the first place. Defective assembly from the factory.
To correct I had to remove the newly installed gear system remove inside cardboard side cover, Remove the screws that hold the bearing for the lift screw so I could remove the chain. After removing the chain I could adjust the plunger to be level and not hit the side of the garbage container on its way down.
clyde from Covington, GA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
12 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The plunger was stuck down
Took the under housing off to see the drive gear. It had broken in half. (Exactly like one of the suggestions said). Replaced the drive gear and re-assembled. It worked great!
Thanks.
Daniel from San Clemente, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
11 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
trashcompacter was getting jamed,making noise
First i removed 2 screws that holds it to the cabinet,pulled the unit out removed the cover off the bottom of the unit,then i notice the gears were damaged,but was not supprised,because the machine gets over worked.Then i removed one clip,removed one gear,the other gear had a pin,tapped the pin out with a punch ,pulled that gear off.then replaced both gears .Got it back together and it now works like new.i am very pleased with your service,you responded right away and let me know the order had filled.i ordered it on sunday night and i recieved it on tuesday morning .i will surly use your service in the future you guys are great. thanks alot
david from tampa, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
7 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic Drive gear broke
The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.
Terry from Spring, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
6 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic gear broke this is the 2nd time in less than 1 year so this is the 2nd repair
Unplugged trash compactor and removed from undercounter. Took cover off and removed broken plastic gear. Replaced with new gear and put cover back on
Mary from Lilburn, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Wrench set
6 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken gear
Unscrew the bottom, pull out the chain, replace the gear.
Francine from bowie, MD
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench set
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
After almost 20 years, the plastic gears had stripped - go figure
Simply removed the two plastic gears (held on by some sort of clip), put the new gears in place using the spacing instructions that were provided in the kit ....... and it is working!
Robert from Springfield, TN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
46 Reviews
4.6
Filter By Rating:
5 Stars
34
4 Stars
9
3 Stars
1
2 Stars
0
1 Star
2
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Chester S - December 16, 2022
Verified Purchase
Perfect part
Repaired trash compactor with this replacement part. Easy to install. Had to reverse the plunger, clean some food debris, then replaced broken gear. Works like new. Easy repair.
★★★★★
★★★★★
Michael T - December 3, 2022
Verified Purchase
Trash Compactor Drive Gears
The 10 year old drive gear had cracked at the hub and would spin on the compactor shaft causing a loud ratcheting sound with no compaction. The new gear set came quickly and even had a modified drive gear with a metal insert at the hub so I expect long life. They fit and work perfectly! So instead of buying a new $1500 compactor I spent $60 on new drive gears and a couple hours of my time. I am very pleased.
★★★★★
★★★★★
Endalesio E - May 17, 2022
Verified Purchase
Exact part
I was able to replace the parts myself and not need to hire a professional
★★★★★
★★★★★
Alton M - February 13, 2022
Verified Purchase
Super Repair Kit
Although I only had a broken gear, this repair kit allowed me to do a complete overhaul. Pretty proud of myself for getting the compactor back into working order.
★★★★★
★★★★★
Allen H - August 20, 2021
Verified Purchase
Very easy repair .
Part worked great. Was about 10 min repair . My only issue was the 7.95 shipping cost and stir took over a week to get here. It went from fed ex to us postal service to deliver makes absolutely no sense .
★★★★★
★★★★★
Dexter B - June 21, 2021
Verified Purchase
Repair was relatively easy, but no instructions accompanied the kit as promised. T
The part was exactly what I needed. Interestingly I had to convince the customer service representative that the part was what I needed and that I should order it.
★★★★★
★★★★★
Vernon L - March 11, 2021
Verified Purchase
Exact Parts and easy repair!!!
The parts were great and fixed the problem!!! Now if they last as long as the original parts I'll be satisfied!!!
★★★★★
★★★★★
Thomas H - February 3, 2021
Verified Purchase
Compactor Repair Kit - perfect fit
4 business day delivery. Part was an exact replacement as advertised. It just took this shade tree mechanic awhile & a YouTube video to figure how to disassemble a compactor. Video was good, too.
★★★★★
★★★★★
Lee M - November 19, 2020
Verified Purchase
Saved a 20 Year Old Compactor
Our Kenmore Trash Compactor finally quit working after more than 20 years in service. I went to the home center to purchase another compactor from the same manufacturer. There are NO compactors to purchase. I guess compactors are not considered essential by the Covid-19 priority monitors. I discovered the broken gear in our compactor, ordered the kit, and installed it. It was a fairly simple install, except that our old compactor had stressed, cracked, and flared the plastic tubes that function as plunger stops. I had to use a small chisel to remove the flared portion of the tubes before I could complete the repair. The parts were a perfect fit and it returned our compactor to like new functionality and it left about $1300 dollars in my pocket that I didn't have to spend on a new compactor.
★★★★★
★★★★★
Pierre D - November 18, 2020
Verified Purchase
It fit!
Easy switch and the appliance is back to work!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS398589
Manufacturer Part Number: 882699
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
