This assembly of parts is a surface burner receptacle kit, and is used in conjunction with your range. The assembly comes with two wires, two wire nuts, two pieces of heat-shrink tubing, and the receptacle. If your element is not heating, you may need to replace your surface burner receptacle. The function of this part is to connect the surface element to the wire harness. The tools you will need for this installment include a number two square-head screwdriver or a number two Phillips screwdriver, a pair of wire strippers and crimpers, and a heat gun.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carlos
April 30, 2018
My oven doesn't heat at all. The clock doesn't work but all of the top elements will burn. What could be the causing this problem. Please help! Thanks
For model number WFC150M0EW0
Hi Carlos,
Thank you for your question. There are a few parts that you could check. I would suggest testing your elements and your temperature sensor. You can test all three of those parts with a multi meter. If they are all working then it may be your electronic control board that is the issue. I hope that helps. Good luck with your repair.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Deborah
January 14, 2019
Trouble with burners on stove they will heat up to high when they are set on low.
For model number WFC150M0EB0
Hi Deborah, thank you for your question. Be sure to cut power to your appliance and remove any parts before doing tests. There are a couple of parts that could cause this issue specifically. You will need a multi meter to be able to test the parts. The first part you will want to check is your element. It should be reading between 0 - 50 ohms to be working correctly. The other part to check would be your infinite (or surface burner) switch. When you remove that part from the appliance, connect each probe from your multi meter to the prongs and then turn the switch to an on position. If you get no continuity then the switch is the issue. It could also be your wiring that is the issue but you should see visual damage on that part in most cases. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Earl
November 17, 2019
Replaced receptacle and stove top burner, burner still doesn't work. What can be the issue?
For model number RF365PXMW1
Hi Earl, the only thing left would likely be the switch for the burner. Thank you for your question and good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Merlin
March 10, 2023
The stove top heating element heats up than it shuts off and than doesn't come back on
For model number Rf303pxkq2
Hi Merlin, thank you for the question. According to our research, there are two sizes of surface elements on the cooktop in this model. If your element size is 8 inches, we recommend checking the infinite switch, part number PS11740775. If this is fine, most likely the burner surface element, part number PS11747315, is faulty and needs to be replaced. Similarly, if your element size is 6 inches, we suggest inspecting the infinite switch, part number PS11740785. If this is fine, most likely the burner surface element, part number PS11753286, is faulty and needs to be replaced. We hope this is helpful!
After turning off the circuit breaker, I removed the elements and pans, raised the top and cut the wires to the receptacle assembly. Stripped the wires, slid on the shrink tubing and applied the wire nuts. I used a hair dryer rather than a match to shrink the tubing. Reinstalled the drip pans and inserted the elements. The instructions were clear and the project was easy. The stove works like new.
This was the second repair of the same problem. I realized this time that there was a poor connection between the burner and the receptacle causing a arch, creating extra heat and burning out the receptacle. All that I had to do was to cut two wires to the existing receptacle assembly and use the wire nuts to connect the new assembly and one philips screw holds it in place...The kit required me to assemble it first and there were four items to put together. No problem....
3 burners had stopped working and drawer glides broke.
Removed the old burners and lifted top assembly. It made it easier to work with the wires by removing the top, easily remove the screws holding the wire harness and ground wire, then slid the top to the right and it came right off. splicing the wires in was very easy and all the parts required were sent with the kits. reassembled stove and it worked like a champ. The drawer was very easy as well the plastic glides were all broken or worn out, and one screw each to replace. like a new oven now, saved at least 300 by not purchasing a new one.
It was very easy, the element is held in place by a point that protrudes from the element's frame through a hole in the stove top. This hole is located directly across from the electrical socket your bheating element plugs into, under the stove top. Push the heating element in towards the socket and the heating element can now be lifted up and out of the burner tray. Remove the burner's reflector tray. Remove the single screw securing the elements electrical socket to the stove top. Lift the stove top up and secure. Remove socket and cut wires about 4 inces from the old socket. place shrink wrap over each wire and wire nut new socket to existing wires. place shrink wrap over wire nuts and heat to secure. reverse proceedure and test.
First I disconnected the power, removed the screw that hold the element in place. Then, I pulled the element out and cut the two wires. I connected the two wires with the new element as the instruction provided by Part Select. I put the element back and screwed it in place. I plugged in the power and turned on the burner. It works. It is really easy to repair.
DAICHI from Louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
6 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out wires and 2 switches.
Unscrewed the switches and let the switch hang while replacing one wire at a time. Followed instructions on wire replacement. Exact parts, only shaft on 6" switch was too long -- okay, because it is designed to break off a piece on end of shaft, then the knob fit. Everything was perfect.
Remove old receptacle and connected and replace new one. Burner now works perfectly again.
ANN from MANITOWOC, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
10 Reviews
5.0
Filter By Rating:
5 Stars
10
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Troy P - October 6, 2021
Verified Purchase
Easy Repair
Part arrived quickly. Instructional video was helpful. Took 10 minutes to repair.
★★★★★
★★★★★
Christopher P - April 29, 2020
Verified Purchase
Relatively straightforward repair, easy with video!
The part arrived exactly as described and the repair was straightforward while following the very helpful video. The only parts that were tricky were:
1) stripping the wires - on my first few tries I ended up cutting into the wire. Got it right eventually without using up all the slack.
2) heat shrink wrapping - I used a lighter and didn't get it to shrink all the way to be snug with the wire. Not sure if it's supposed to be completely snug.
Also bought a new element because the prongs on the old one were corroded. The repair was successful and works great now!
★★★★★
★★★★★
Karen Z - January 23, 2020
Verified Purchase
Great part
easy instalation, work great
★★★★★
★★★★★
Art S - December 31, 2019
Verified Purchase
Easy repair
This part worked as it should. The element now heats up like it should.
★★★★★
★★★★★
Lawrence R - November 22, 2019
Verified Purchase
Great part
The part fit perfectly and I am pleased with how easy it was to get!! I put in a model number and found all I needed.
★★★★★
★★★★★
Paul R - March 28, 2019
Verified Purchase
8" stove eye & connecting receptale
The part was as advertised & easy to install. Great company to do business with. Paul Rogers
★★★★★
★★★★★
Norbert A - March 26, 2019
Verified Purchase
receptacle kit
burner on stove repaired and working
★★★★★
★★★★★
Lois S - August 16, 2018
Verified Purchase
Great part.
Great part. Fitted perfect. Thanks
★★★★★
★★★★★
Lou F - April 13, 2018
Verified Purchase
Repair to burner
The part came quickly after I ordered it at store. The Clerk was very helpful. We received it and fixed the stove in no time flat Thank you
★★★★★
★★★★★
Marc M - February 9, 2018
Verified Purchase
Easy repair and good quality parts
There was a little confusion on how to assemble this, but I found a PartSelect video on youtube that cleared it up. The rest went really well.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
