We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Abdul
November 20, 2017
Hello my dish washer stop working, the motor stop moving.How easy or hard to change the motor on this model.
For model number LDF7932ST
Hi Abdul, Thank you for the question. I am not able to tell you how hard it is as it depends on your skill level. First remove the appliance from the water and power supply. Next removed the racks, screens and impeller inside and then lay it back on its side to access the motor. Unplug the wire harness from the motor. A flat head screw driver may help.Unscrew and disconnect the single wires on the side,taking note of where they go. Taking pictures will help. Remove the screws holding the motor in place. Once the screws are removed the motor will just pull out. Reverse the steps to reinstall. Hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Tom
December 3, 2017
Would this cause a noisy operation?
For model number ldf692ost
Hi Tom,
Thank you for your question. Yes, if there is noise in your dishwasher then the circulation motor assembly is probably causing it. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Richard
April 29, 2018
There does not seem to be any water coming out of the upper spray arm. I took it off and cleaned it, it still does not work. The dishes in the top rack are not wet. Also, there is an FE code showing. Can you help?
For model number LDS5540ST
Hello Richard,
Thanks for your question. The FE error code indicates a fill error. The water inlet valve could be the cause of this issue. Consider testing the valve with a multimeter for electrical continuity and replace it if it shows no continuity. Examine the mesh filter as well for any signs of wear and tear.
I hope this helps.
I am looking to replace the full wash assembly, there was rusted metal parts and i had the le error code. When i checked for a clog i noticed the rusted bits. I would like to replace the full motor assembly not just the motor. What part number would that be?
For model number Ldf7811st
Hello Shanna, thank you for your question. The assembly would be PartSelect Number PS3579321. This is the Dishwasher pump and motor assembly with pump housing gasket. The assembly includes a turbidity sensor in the pump housing. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Richard
March 28, 2018
LG dishwasher with an le error code, reset by powering down for approx. 5 minutes still get the le error code, could it be something preventing the motor from turning or is it just a motor failure?
Hi Richard, Thank you for the question. The LE error code is an indication of a Motor issue. The issue that may cause this fault code is a wiring problem, the impeller of washing pump is locked, the rotor of washing motor is locked, the blade is locked, or the PCB main control board is faulty. If you can provide the model number of the appliance we will be able to pull up more details. Hope this helps!
Was this helpful?
Thank you for voting!
Marco
May 31, 2019
Hello, my dishwasher is making a grinding sound when in wash mode. I am asssuning the motor is going bad. I have a couple questions, first is this the correct part number for the motor m060? Do you sell just that part? And what about the whole assembley, part m006, is that what is listed for $131? My dishwasher model is lds4821st. Thanks
For model number LDS4821ST
Hello Marco, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS3579321. Hope this helps!
Was this helpful?
Thank you for voting!
Erik
October 15, 2019
Is there a way to bench test the motor to make sure it is the culprit for my le code
Can i use a multimeter to determine if it is a bad part
For model number LDF7810ST
Hello Erik, thank you for your question. You can test this Circulation Motor Assembly with a multi-meter. Test the ohms of resistance. Any reading over 100 is a good reading meaning the Motor is in working condition. Good luck with your repair!
Was this helpful?
Thank you for voting!
Corey
February 24, 2020
I have a hot electrical smell and code le on display. I can reset it and it will work again but the smell is still present. Water is spraying and arm seems to be spinning.
For model number LDS5560ST
Good Day Corey. Thank you for your question in regards to your unit (Model Number LDS5560ST). Based on our research the LE code on your unit is a sign that it has detected a Motor Error. Some of the most common reasons for this are the following: 1) There is a wiring issue and the wiring harness (PartSelect Number PS7790912) may need to be replaced. 2) The impeller on the washing pump is locked. 3) The Control Board (PartSelect PS8749407) has become faulty and may need to be replaced. We hope this helps! Best Regards.
Error LE is displayed. Do you think that the Circulation motor needs to be replaced?
For model number LDF6920ST
Hello Nate, Thank you for the question. The LE is a Drain Pump Motor Error. This can be caused by the impeller of pump being locked/jammed. We suggest checking to make sure there is no debris or damage preventing the impeller from spinning. If it looks ok, you can check the wiring for any damage. If everything looks good, the Drain Pump may need to be replaced. We hope this helps!
Average Repair Rating: 1.8 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Whining motor noise during wash cycle.
The noise is caused by a defective motor bearing. The bearing fails due to water intrusion after the motor shaft seal in the sump assembly starts leaking. It maybe worthwhile to replace the entire sump assembly ( illustr. M007) instead of the motor only to prevent premature failure of the replacement motor. (Unfortunately the shaft seal is not available as a separate part).
Dishwasher was noisy. PartsDirect suggested replacing circ pump.
Relocated dishwasher to garage and set it up on a table (easier on back having it elevated). Connected temporary water supply, drained to a bucket.
Removed pump, and found it severely corroded, indicating leakage from pump shaft seal in sump. Inspection of seal revealed excessive wear, requiring sump replacement (there is no way to replace just the pump seal). I have photos of old pump & sump, but I don't see any way to upload them.
Removed sump from dishwasher with all components attached, swapped components over to new sump, reinstalled sump (with new sump gasket) and started dishwasher to check for leaks. The heater was the most difficult component to swap. Reinstalling the sump assembly was tricky.
Reinstalled dishwasher into kitchen cabinet.
Doug from NEWPORT NEWS, VA
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
5.0
Filter By Rating:
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Johnny S - May 11, 2021
Verified Purchase
Perfect fit
The pump was a perfect fit. No adjustments needed.
★★★★★
★★★★★
Schmidt R - February 19, 2021
Verified Purchase
Great Service
This part came in the time frame expected and worked great. However, my dishwasher still wasn't working properly, and found I needed an additional part. I ordered it from PartSelect at about 3:30 pm, figuring I would get it in a couple of days. To my surprise, I went out early the next morning and the part was delivered to my front door. Don't ask me how PartSelect got it there so fast. Saved me from my wife complaining that I should have called a repairman instead of doing it myself. Now it works great and my wife is happy she doesn't have to wash any more dishes! Thanks, PartSelect!
★★★★★
★★★★★
Michael B - April 24, 2020
Verified Purchase
Perfect fit.
Part was exactly what I needed. Perfect fix.
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3579321
Manufacturer Part Number: 4681ED1004B
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
