This magnetron in your microwave creates the radiation needed for cooking or warming your food. It is located inside the main cavity, typically near the transformer or waveguide. When the magnetron becomes defective, your food may not heat up properly or heat up at all. Additionally, buzzing or humming sounds may be noticeable while the microwave is in operation. With a malfunctioning magnetron, your microwave loses its primary function. To remove it, you first need to unplug your microwave from its outlet. Before touching any components, discharge the capacitor by placing a screwdriver, with an insulated handle, across the two terminals of the capacitor. Once the capacitor is discharged, replace the current magnetron by disconnecting it from any wires and removing any mounting screws or clips. This magnetron is sold individually and is supplied directly from the original equipment manufacturer.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
John G - April 2, 2023
Verified Purchase
Worked as expect. Easy fix. Quick delivery as well
We have purchased several parts from here. Always quick and accurate. The part was exactly what was needed. Appliance back in working order. Much better than having to purchase a new appliance.
★★★★★
★★★★★
Doug P - June 10, 2020
Verified Purchase
Magnetron
This is a quality part and simple to install. Saved me from buying another microwave, as you cannot buy a toast wave anymore.
★★★★★
★★★★★
Jack B - May 23, 2020
Verified Purchase
Microwave not heating
Parts were the right ones and worked well
★★★★★
★★★★★
Thomas K - April 15, 2020
Verified Purchase
Reasonable Price, OE Quality
Its the same part that came out of the microwave. The original lasted 17 years. I figure this one will too. $70 vs. a new microwave for $350 made it a fairly easy choice.
★★★★★
★★★★★
Laurian E - March 28, 2019
Verified Purchase
Magnetron Part Replacement
Replacement of the magnetron part was very simple. This was a worthwhile project instead of replacing the microwave oven. It was great that the part was readily available. Microwave oven works like new!
★★★★★
★★★★★
Edward B - February 21, 2018
Verified Purchase
magnetron for Kenmore microwave oven
It took a half an hour to install and ti seems to work very well.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
the turn table no turn and no heat the food. but the bottom oven worked
well I unplugged the microwave one day prior to working on it. shock precaution smart way to do this job. very easy pullout the screws behind the unit pull off the outer casing. minor screws inside the unit you have to remove a couple things out of the way. unplug the magnetron and remove first gives you more room to work on the side pane
... Read morel to replace the micro switches. I only replaced one the bottom micro switch. only one bad, but since I was in there I clean the bulb and changed the magnetron any ways. I read other reviews and made my choice to do so. it works perfectly now. Thanks PartSelect for having parts.
Would not heat and made a buzzing or popping sound
Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other
... Read moreand then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.
Read less
Thomas from NEWARK, DE
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Magnitron failed
Over the stove microwave installed in top cabinet row. 1. Unplug device. 2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet. 3. Remove screws from sheet metal cover
... Read more. 4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place. 5. Unplug magnetron and remove the 5 screws. 6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3). 7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.
Read less
Joseph from WILTON, NH
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
8 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of Magnetron
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations
... Read moreon the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Read less
Benjamin from Anchorage, AK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dan
February 11, 2018
The unit seems to work like it should but its not heating up wife said she heard a pop then it wouldn't heat up
For model number LMHM2017SB
Hi Dan,
Thank you for your question. I would suggest taking a look at your fuse and the diode on your appliance. Be careful when doing any repair on a microwave. You have to make sure you safely discharge the capacitor inside of your microwave before preforming any installations or repairs. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Wycliife
July 24, 2019
The machine is working normally but not producing heat. What could be the problem?
Hello Wycliife, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
2 people found this helpful.
Was this helpful?
Thank you for voting!
David
December 12, 2019
Microwave ran on high for 10 mins with nothing in it. Now it won't heat anything inside. Interestingly, the outside of the microwave will heat up if you try and heat something.Any way to tell if this is magnetron vs fuse?
thanks!
For model number LMH2016st
Hello David, thank you for your question. We would recommend testing the fuse. It's easy to tell if a glass fuse is blown; it will show scorch marks, and the filament will be melted. To check a ceramic fuse, use an ohmmeter or continuity tester. With an ohmmeter or multimeter, you should see a reading close to zero ohms if the fuse is intact, or infinite if it's blown. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Ramon
January 13, 2020
Microwave suddenly stopped working. I have no lights or anything coming from the microwave. Im sure its just a fuse but im really reluctant to try to open it up and work on it. Any suggestions?
For model number LCS1413SB
Hi Ramon, Thank you for your question. There are a few parts that you could check for this issue. Please be advised, you must unplug the appliance from power and safely discharge the capacitor before attempting any repair as the capacitor can electrocute you if not properly discharged. You would be able to test these parts with a multi meter, remove them from the appliance before testing. First you should take a look at your fuse being the issue. It should be reading 0 ohms to be working correctly. You should also check your diode. You will also want to test all of your door switches to make sure that they are working. They should also be reading 0 ohms to be working correctly. If those parts are fine then the issue might either be in your capacitor or your magnetron itself. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
