Shock Absorber Kit 5304485917

Removed the back and lower panel in the front of machine. Turned it on its side to replace spring, not tools required. Then stood it up and replaced both shocks by removing plastic pins that hold them in place, no tools required. The only time you need tools is to remove the metal panels to get to the parts. Now it makes no noise and runs like a new washer. Paid $140 for the parts, a new machine would have cost over a thousand and would be one of those digital nightmares that don't last as long. This machine is 18 years old.

The video was most helpful, and the left shock replacement went as shown. The sucker punch was getting to the right shock - much harder.
First notice video has washer on a stand. How nice to have had it up on a table. LOL As it was I tilted the machine back with a 6 inch block under the front. Still a bear to get to the shock, but w/ patience, doable even though you are flat out on the floor.
The old shocks were so bad that the pistons fell out once it was removed.
It takes some strength to get the pins through the new shocks, and as I have a weak left hand I had to resort to using a C-clamp to help. If I could have gotten my right hand in there I may not have needed it. Right hand did have to hold the clamp as it had to just catch the side of the pin hole since the pin is pointed and sticks out past the mounting bracket when seated.
I also ordered a spring but they both were still good.

Watched the video on website and followed what they said. Worked great.

The instructions that come with parts say to pull pins out with pliers. not much room to do that. I used hammers and punches where I had access and prybars nail puller an hammer to offset where the water outlet was in the way. I used a short handle hammer to install three of the pins. The third I used a prybar and spacer blocks.

Pulled the locking pins out, replaced the shock absorbers and re-installed the locking pins. I used Channel Lock pliers to remove and replace the locking pins. i used a deep socket to hold down the tab on the locking pins so they could be pushed out. The new shock absorbers came with installation instructions.

I did my best to stretch the belt out and as I wrapped it around the pulley one hand was preventing the belt from slipping off and the other hand had the screwdriver to use as Leverage to stretch and slip the belt on the other side of the pulley. One thing that I saw but didn't try was to use zip ties to temporarily hold the belt in place so it didn't slip off that may have helped.

Remove front panel to expose shocks. It took some time to remove the old shocks, both were broken. The pins were somewhat difficult to reach and remove, especially the one on right for it was shoved up against the electric wiring box. We ended up putting that pin in backwards for the new shock because it was impossible to reach from rear. Putting the new shocks was easy it was removing the old ones that took most of the time. The washing machine is working perfectly now.

the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.

The replacement of the Shock Absorber Kit was hampered on the right side by a metal box that was mounted just a little shorter than the bottom plastic pin. the deadblow hammer with the dowel worked with all the pins including the impeded pin and the top right pin which had to be removed at an angle. The replacement did not repair the washer - it is the tub bearing which went in a previous washer of a similar model about 4 years ago.

Remove the front lower panel. Remove the 4 plastic pins mounting the shocks using 1/2 inch short socket to hold the detent down as per included instructions. All plastic pins were stuck in place so used needle nose pliers to pull or push out. Lube the pins with grease before reinstall to help them go through the new shocks. Use the included lock nuts to lock the four legs in place as low as possible. Start the washer and level each leg while running so you can tell if the vibration is going away. Tedious method but worked.