This OEM replacement dryer slide bearing is white in color, and approximately 3 inches long. The slide bearings are supportive linings for your dryer. If they have eroded, or are damaged, the drums will scrape against metal during the drying cycle which will produce a squealing, or scraping sound.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Noisy | Marks left on clothes
This part works with the following products:
Dryer, Washer Dryer Combo, Washer.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WE03X34318 replaces these:
WE3M52
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
5.0
Filter By Rating:
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Margaret J - February 10, 2024
Verified Purchase
easy repair just what i needed
good condition. appliance is working better than before
★★★★★
★★★★★
Aaron M - March 29, 2023
Verified Purchase
Right parts.
Right parts. Good service. Will use again.
★★★★★
★★★★★
Hector F - April 24, 2018
Verified Purchase
great
machine back to normal
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.6 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dryer was making increasingly loud "thumping" sound.
Parts were shipped quickly, packaged correctly, and were in original GM packages - very reassuring. BTW, your customer service is excellent. Reviewed YouTube videos. Patience is required, take your time, take photos of the wires and also make a written wiring chart. This was the flaw in my planning. Reference the schematics f
... Read morerom PartsSelect to number the controls. Do NOT use masking tape to identify the wires as they will have all stuck together by the time you go to reinstall them. Most difficult process was removing and identifying the numerous wires to the back panel. They have push connectors, but some were very difficult to remove. The people doing the "how to" videos no doubt had them partially released and that made it look easy. Examine the connectors before removing to identify how they are captured by the connector. A paper clip "tool" I made enabled me to release some of the capture lugs, but some were so tight, I had to use small needle-nose pliers to open up the lug to release the wire on the connector. When reinstalling, re-tighten those connectors. Replacing the parts was much easier than the wiring disconnect/reconnect process. I'm happy to report that replacing the rear bearing and the front 2 green and 2 white shim/bearings immediately and completely solved my problem. For about $150, I restored my dryer to "like-new" functionality and got a lot of satisfaction from doing it. The project took about 4 hours, which could have been reduced to 2 hours had I know about the clip release and wiring identification process. Also, make sure you thoroughly vacuum out your unit while it is disassembled. Good luck!!!
To get to the slides, needed to take off the front panel, the top and then can loosen the front of the dryer. Pull it out enough to get to the slides and replace them.
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Margaret
March 25, 2023
How many drum bearing slides does this dryer have.
For model number Gtd65ebsj3ws
Hello Margaret, We are glad you asked! This unit takes two(2) of Green Slide PS16762550 and two(2) of White Slide PS4704230. We are pleased to have been able to help.
Can I purchase the drum glides as a complete kit and what part number and how many. Thank You
For model number Gfds170ehoww
Hello Matt, thank you for reaching out. There are two drum glide bearings for your model, part number PS4704230, and part number PS16762550. You may need to order them separately as they do not come in kit. If you need help placing an order, customer service is open 7 days a week!
Hello Mike, thank you for asking. According to our research, your model contains four bearing slides. You may need to order two white bearing slides, part number PS4704230, and two bearing slides, part number PS16762550. We hope this helps!
