This kit includes the shaft, 3 bearings, seals , grease, adhesive and the spanner nut, which is NOT sold separately. Also may require a bearing driver tool to install. PS3503307
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer.
This part works with the following products:
Maytag, Whirlpool, Kenmore.
Part# W10435302 replaces these:
AP5325033
Customer Reviews
Average Rating:
★★★★★
★★★★★
11 Reviews
4.5
Filter By Rating:
5 Stars
6
4 Stars
5
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Augustine D - August 19, 2022
Verified Purchase
Perfect in every way !!
The parts were perfect in every way. So, too, were all aspects of the procedures for finding them, ordering them, and receiving them. I used instructions from YouTube to install them with no trouble at all. I already had the installation tool for these parts.
★★★★★
★★★★★
Frank S - April 29, 2020
Verified Purchase
Perfect match
Parts were excellent !!! Also purchased the installation tool which helped tremendously to speed up the whole process. We took two days only because we cleaned the tub out the next day, after the sealer dried. Runs so quiet now. We are totally satisfied with the whole experience.
★★★★★
★★★★★
Matthew H - December 27, 2019
Verified Purchase
Clothes washer repair.
Tub bearings arrived quickly, installation was easy and appliance is back in operation.
★★★★★
★★★★★
Jack B - August 28, 2019
Verified Purchase
Parts as needed for repairs
Most of the parts were in good condition. The only problem was the seal is in a sealed plastic bag and was not as protected as it should have been. From shipping the seal was a little deformed but did work. Parts came fast and I was not able to work on unit for a couple of weeks due to work load. Machine is back into operation and working good.
★★★★★
★★★★★
Dallas D - March 13, 2019
Verified Purchase
Maytag bearing repair
The bearings, seal, and shaft were all correct. After I replaced them the washer worked great with little to no noise like it did when new.
Only comment I have is, there’s no instructions on how to use the parts. Try putting the DIY instructions in with the parts.
★★★★★
★★★★★
Scott G - February 14, 2019
Verified Purchase
Perfect parts
Directions included with the kit were cursory, do your self a favor and watch the Parts Select videos.
★★★★★
★★★★★
Wendy H - February 12, 2019
Verified Purchase
Maytag Bravos Washer Barrings
Part was good quality and delivery was fast!
★★★★★
★★★★★
Timothy G - January 21, 2019
Verified Purchase
Good part
Part came quickly and matched exactly.
★★★★★
★★★★★
Duane W - November 27, 2018
Verified Purchase
tubseal and bearing
The parts came fast. The parts fit like a dream. It took about 2 hours
★★★★★
★★★★★
Kenneth K - October 29, 2018
Verified Purchase
Good Parts, repair went fairly well
I purchased a Main Shaft w/ upper & lower bearings. Kit came complete with seal, grease, and adhesive. I was disappointed that no instructions came which could have been a disaster if I did not have experience in general machine repairs.
Without instructions, I would not have known the adhesive used to seal the outer lip of the shaft seal needed 24 hours to cure before introducing water. Personal past experience told me to lookup the specs and see what the adhesive manufacturer recommened.
Overall the parts were good and a YpuTube video was very informative to fill in the blanks
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 1.7 / 5.0, 5 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Bearing did not fit right on the shaft
I finished by modifying the agitating nut to make it work
Kur from YUBA CITY, CA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Watched a couple of videos online to get a good grasp on repair. Opted out of purchasing the bearing press tool $130. Struggled a little, but made the repair. At the very least the wash tub needed a good cleaning
Barry from PANAMA CITY, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
8 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was loud during spin cycle and began leaking water from underneath (not either pump)
I followed a youtube video by Appliance Repairs, 32-34 minutes long that was very thorough.
Daryl from Devils Lake, ND
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
12 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was noisy, Top seal and bearing bad
You better be confident in your repair abilities before you try this. Get the washer to a large open area, like your garage, because there are a lot of parts. Take off the back, pop the top, unsnap and remove the top ring off outer tub, take out the agitator, take out the inner tub, disconnect the pumps and electrical wires, take screw ou
... Read moret of rotor on bottom and remove rotor, take out 4 bolts to remove motor magnet ring, and now you may be ready to unhook the outer tub from the 4 supports (springs) and lift it out of the metal frame. Then unscrew the bottom nut on the shaft, use blocks to hold the tub in place, and carefully tap the old shaft and bearings out. The instructions that came with the kit helped. The shaft and top seal comes out the top first. Then you can tap out upper bearing and then the lower bearing and spacers.Instructions called for a special tool to install the bearings but you can carefully tap them in. You will need blocks to support the tub while you tap them. First block under the tub and install top bearing, then flip over and use several blocks to hold tub while you drop the shaft, spacers, and tap lower bearing in. I did not need to tap on the inner ring of the bearings, just the outer ring. Be very careful not to damage the seal in the bearings. That's why you must tap them in careful and slow. Them install the nut on the bottom. You need to hold the shaft with damaging it while you tighten the nut. I used the hard nylon gear from the inner tub which I was replacing with a new one. Then put it all back together.
Read less
DENNIS from OELWEIN, IA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
150 of 162 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
25 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim
November 21, 2018
Is there a video on how to install the bearing kit
For model number MVWB700VQ0
Hi Jim, thank you for your question. Unfortunately we do not have a video for this part and model specifically. However we do have an video on a similar installation that may help you: https://www.youtube.com/watch?v=cWe8YAMM_Ds&t=258s. I hope that helps. Good luck with your repair.
13 people found this helpful.
Was this helpful?
Thank you for voting!
Diane
February 22, 2019
The tub shaft & bearing kit....what kind of warranty is on these parts?
For model number W10435302
Hello Diane, Thank you for contacting us. We offer a one year manufacturer warranty on all of the parts on our website. Have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Jerry
July 23, 2019
My wife found that the washer had leaked some oil out on the floor recently, and now it is very loud during the spin cycle. Would you recommend the w10820039 basket hub kit or the w10435302 tub seal and bearing kit for our repair?
For model number WTW8500BW0
Hello Jerry,thank you for your question. We would recommend replacing the tub seal and bearing kit to fix this issue. I hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Bonita
May 7, 2018
My problem is the ol code comes on with nothing in the tub. When i try to do a load it washes for about 10 min. Than water is coming in and is going out but it will not advance to the next cycle. Just hums than the ol code comes on
For model number WTW7340XW0
Hello Bonita, thank you for your question. I would recommend replacing the sensor part number WPW10178988. This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. If the sensor isn't working, the unit might be stuck in "unbalanced mode". Try unplugging the unit and leaving it for about 10 minutes, then plugging it back in to see if that resets it. I would also check the tub seal and bearing kit to be sure the tub is turning freely as any corrosion or debris around the bearing and seal can cause the tub to not spin freely. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Donald
February 6, 2019
My washer stops with about 12 minutes left and the load is not spun out all the way it will not spin no more. Also is very loud when spinning. What parts would you recommend?
For model number Mvwb300wq1
Hello Donald, Thank you for contacting us! I suggest checking the following parts: PS11723155 Basket Hub Kit, PS5136124 Drain Pump, and PS11752033 Washplate. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Max
November 11, 2019
Would these be the correct parts for my washer bearing set
For model number MVWB725BW0
Hello Max, Thank you for the question. I have researched the model you have provided and have found the Tub Seal and Bearing is only sold as part of the Outer Tub, PartSelect Number PS3503107. I looked up the part and it is listed as No Longer Available/Discontinued sorry. There are no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. Hope this helps!
My Maytag washer is nosy when it run to about 9 min to end 0. What parts do i need to change? Thanks
For model number mvwb300wqo
Hello and thank you for writing.
It certainly sounds like it could be a faulty basket hub and/or possibly a malfunctioning tub seal and bearing you should check the part(s) for signs of damage, and replace it as needed. Please see the part links related to this question just beneath this answer. We hope this helps. Please contact us anytime if you require further assistance.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Sharon
January 27, 2020
Thanks for asking my question. Can you please also tell me how to check the parts for signs of damage " faulty basket hub kit or malfunctioning tub seal and bearing"
Thanks
For model number MVWB300WQ0
Hello Sharon and thank you for writing.
The seal and bearing: Fill up the tub partway, put a little bit of detergent in it and let it just hang out.
Check an hour later and there it is. Soapy water on the floor, not so much in the tub. You can also inspect the seal for cracks and missing pieces, being brittle.
The hub kit: The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced. You again would need to inspect these plastic parts for missing teeth or broken or cracked pieces. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Larry
March 21, 2023
Our machine has a very loud growling during spin cycles, like dry/bad bearings sound. Plus has developed a leak. What part(s) do I need to make the necessary repairs?
For model number WTW8540BW0
Hi Larry, thank you for reaching out. Based on our understanding of the issue, we would suggest checking the hoses for leaks. You may also need to check the following parts: basket hub kit, part number PS11723155, and suspension rod kit, part number PS3502193. We hope this solves your problem!
Hello Alistair, thank you for your question. No, it is not compatible. There is a Tub Seal Kit part PS3407958. The bearing are not sold separately. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
