Maytag/Maytag_Thumb/43273.gif
See part 10 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Drive Motor

★★★★★
★★★★★
1 Review
$295.95   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS3497647
Manufacturer Part Number W10410996
Manufactured by Whirlpool
Product Description

Drive Motor Specifications

This drive motor rotates the drum by turning the belt.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will Not Start | Noisy
This part works with the following products:
Dryer.
This part works with the following products:
Magic Chef, Norge, Maytag, Crosley.
Part# W10410996 replaces these:
AP5272116, 31001015, 31001316, 31001473, 31001512, 31001589, 53-2275, 53-2567, 53-2590, 53-3251
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

7 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Randy Miller
    January 5, 2018
    On the drive motor.Can a guy just buy the wheel the belt rides on
    For model number ADE7000AYW
    Hello Randy, Thank you for your inquiry. The motor pulley that the belt slides onto is available as a separate part, part# WP31001535. Hope this helps!

    6 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Dan
    September 19, 2017
    When I push the start button I get a hum but the dryer does not start. If I continue to push the start the hum eventually will just stop. Is this more than likely the motor? The dryer is 15 years old.
    For model number pyg2300aww
    Hi Dan, Thank you for the question. It sounds like it might be the Timer Assembly,PartSelect Number PS11742813. If the timer is not working it will not start the dryer into the dry cycle. If the motor is making a hum then it should like it wants to start but it is waiting for the signal from the timer.To be sure you can do some electrical testing with a volt meter to check for continuity. It is also good to check the Door Switch.This dryer door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.When defective it thinks the door is open. Hope this helps!

    5 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    John
    March 8, 2019
    We push the button to start and it has a hard start but then it will run. If we do a continuous use during a laundry day the dryer will stop working until we let it sit for about 1-1.5 hours. What could be the issue?
    For model number LNC7764A71
    Hello John, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: High Limit Kit, Control Thermostat, High Limit Thermostat, Heating Element, Drive Motor, and Door switch, and Door catch kit. You can test the parts with a multimeter. Hope this helps!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Tom
    April 6, 2018
    Hello. I would like to know if the motor pulley part number wp31001535 is compatible with my dryer model pygt244aww. I could not find it on the list. I have a broken pulley and the belt that need to be replaced.
    For model number PYGT244AWW
    Hello Tom, Thank you for your inquiry. We do show that it is, it is listed as an accessory in our database. Hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Magdalena
    October 17, 2017
    My dryer has a high pitched humming noise that comes and goes, so far I've replaced the belt,rollers,glides and idler pulls wheel.... do you think at this point i have to replace motor?
    For model number PY62300AWW
    Hi Magdalena, Thank you for your question. It could be your motor that is the issue however I would also suggest you take a look at your glides. In a lot of cases when you get that high pitched noise, it is because the glides have worn down. If they are fine though, it may indeed be your motor that is the issue. I hope that helps. Good luck with your repair.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Bruce
    August 1, 2019
    Do you stock the rubber bearing for the rear of the motor? It fits between the bracket, parts 7 and 8 in the diagram. Thanks
    For model number YG225LV
    Hi Bruce, thank you for your question. That piece is part of the motor. So to replace it you would have to replace your motor. Good luck with your repair.

    Was this helpful?
    Thank you for voting!
    Fred
    February 28, 2020
    How do you remove motor to replace drive pulley?
    For model number (P)HYE3658AYW
    Hello, Thank you for your question. If you go to the part on our site- https://www.partselect.com/PS3497647-Whirlpool-W10410996-Drive-Motor.htm?SourceCode=4&SearchTerm=HYE3658AYW&ModelNum=HYE3658AYW There is a section you can scroll to about customer repair stories.We hope this helps.

    Was this helpful?
    Thank you for voting!
      Customer Repair Stories
       Average Repair Rating: 3.0 / 5.0, 7 reviews. What's this?
        Sort by:
        Sorry, we couldn't find any existing installation instruction that matched.
        Dryer would'nt start / drum wouldn't turn
        Unplugged Dryer; used screwdriver to push in and release two clips that hold top to front, tilted top back and removed two screws holding front to sides. Disconnected door switch and removed front .
        Reached in above motor to remove belt from around pulley and tensioner wheel, Pulled drum and belt out of machine.
        Removed approximately 10 screws around perimeter of blower housing and removed cover to access blower wheel. Removed outer lock ring from shaft and clamp from blower wheel hub, and removed blower wheel.
        Took out tensioner assembly.
        Disconnected wiring connector from motor.
        Removed three screws that held blower housing to bottom and removed retainer around rubber motor mount at pulley end of motor. Lifted out motor, blower housing and vent pipe as one unit.
        Removed 2nd outer lock ring from motor shaft.
        Rotated motor frame 45 degrees to free the rubber mount from the blower housing.
        Screwed new pulley onto new motor shaft and cleaned blower housing and vent pipe.
        Assembly is reverse of disassembly.
        Inspected and lightly greased the glides and inspected the idler wheels before reinstalling drum.

        Dryer works perfectly.

        Five to ten minutes also spent unscrewing and replacing timer knob and hinge pins on lid of matching washer Crosley cw22b5v.

        Very simple repair.
        52 of 77 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Squealing Berring
        I had to replace the whole motor, Idler spring and idler Pulley Wheel. It went well but I wish I could have replaced just the berring and not the whole motor.
        • Marty from Sterling heights, MI
        • Difficulty Level:
          Easy
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Socket set
        • Parts Used:
          W10410996, 31001465, WP31001344
        11 of 38 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Dryer Quit running
        First off I want to say I ordered my motor on Sunday night at 11:30 PM on veterans day and got the two day delivery. My part was sent out on that Monday (fed. holiday) and I received it Tuesday around 1:00 pm after I disconnected the wiring harness, took the blower fan C-clips off, unscrewed about 6 screws, and pulled the assembly apart I just done everything in reverse and replaced the new motor. I discovered that my thermostat fuse was blown so I ordered the High temp thermostat kit from here (two day delivery) on Wednesday at 10:30 PM and got the parts Friday at around 2:00 PM. After taking out four screws and four wires I replaced the fuse and high temp. set, pushed the start button to see if it worked and it started up like new. Now it heats twice as fast and everything doesn't have a light burnt smell. So dry time is faster (no more 80-90 min. cycle times), less dryer sheets (to cover smell) and all this added up to cost savings on electric bill and dryer sheets. It took a week to get my dryer back (because I just looked at the motor) but in the end I needed the fuse and motor. The quick turn around time to get the parts, the pictures to see if I had the right parts, and the ease of ordering the parts meant only one run to the laundry mat, and that wouldn't have happen if the dryer hadn't messed up on laundry day.
        • William from Marion, VA
        • Difficulty Level:
          Really Easy
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Screw drivers
        • Parts Used:
          W10410996
        6 of 7 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Motor froze up
        First lift the top and remove 2 screws holding the front panel on, at each top corner. Release the door switch from its clip (or disconnect the wires). Remove the front panel by tilting out and then lifting it up off the bottom tabs. Remove the belt from the motor by releasing the tensioner. Then lift the drum out. Remove the front blower cover, then remove the tensioner by first removing the spring, then pull the tensioner out toward the back. Remove the strap on the back of the motor near the pulley. It takes a little effort to get the strap off. Remove the 3 bolts holding the blower case (with the motor still attached. Remove the motor wires, then lift the motor and blower case out. Next remove the clip holding the blower fan on and remove the fan. It may be stubborn so be patient and slowly work it off. Remove the next clip behind the fan. Then remove the motor from the blower case by turning it counter clockwise (as viewed from the motor side). Installation is the reverse.
        • Randy from Loganville, GA
        • Difficulty Level:
          A Bit Difficult
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
        • Parts Used:
          W10410996
        5 of 5 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Noise when running and motor stop. Motor bearing overheated.
        Unplug dryer

        Pick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.

        After you clean out any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.

        The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.

        The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.

        From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.
        • Jeffrey from Rogers City, MI
        • Difficulty Level:
          A Bit Difficult
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Nutdriver, Screw drivers
        • Parts Used:
          W10410996, 341241
        5 of 7 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Motor Bearing and Cracked Blower Wheel
        1. Opened top and removed wire clamps from side and front for door switch.
        2. Removed two screws and pulled front cover off.
        3. Removed drive belt from tensioner pulley and moved to back of dryer.
        4. Pulled drum off rear guide wheels and lifted drum out of dryer.
        5. Unplugged motor electrical connector and removed idler wheel spring and idler assembly.
        6. Removed screws holding blower wheel cover to case.
        7. Removed snap ring and spring clamp from blower wheel and pulled blower wheel off motor shaft.
        8. Popped rear motor clamp off with screwdriver.
        9. Unscrewed screw holding rear motor support to dryer bottom and removed rear motor support.
        10. Twisted motor assembly 1/8 turn to right and pulled motor rearward out of blower housing.
        11. Removed blower rear snap ring from old motor and moved to new motor shaft.
        12. Reversed procedures 1-10 to install motor, connector, idler, blower wheel, blower wheel cover, drum, belt, front cover and top cover.
        • Craig from Westfield, IN
        • Difficulty Level:
          A Bit Difficult
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Nutdriver, Screw drivers
        • Parts Used:
          W10410996, W11497304
        2 of 6 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Motor making rattling noise
        Released lid clips, two screws removed to remove the front. Took tension off of the belt by removing it from roller, then lifting tension spring from base. Removed drum to gain full access to motor. Lubricated rollers, vacuumed all areas to remove lint. Replaced motor and belt. Re-installed drum and re-attached tension spring, dryer face, and top. Works fantastic. Hard part was getting spring released and reattached due to location.
        • Richard from Ames, IA
        • Difficulty Level:
          Easy
        • Total Repair Time:
          1- 2 hours
        • Tools:
          Nutdriver, Pliers, Screw drivers
        • Parts Used:
          W10410996, 341241
        1 of 3 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
          Customer Reviews
          Average Rating:
          ★★★★★
          ★★★★★
          1 Review
          5.0
          Filter By Rating:
          • 5 Stars
            1
          • 4 Stars
            0
          • 3 Stars
            0
          • 2 Stars
            0
          • 1 Star
            0
            Sort by:
            Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
              Model Cross Reference
              This part works with the following models:
              PartSelect Number: PS3497647
              Manufacturer Part Number: W10410996
              Brand
              Model Number
              Description
              Norge
              7002A
              Dryer - DRYER
              Norge
              7433A
              Dryer - ELECTRIC DRYER
              Norge
              7433A REV A
              Dryer - Norge Dryer Model 7433A REV A (7433AREVA) Parts
              Norge
              7543A
              Dryer - ELECTRIC DRYER
              Norge
              7543A REV A
              Dryer - Norge Dryer Model 7543A REV A (7543AREVA) Parts
              Norge
              7643A
              Dryer - DRYER
              Norge
              7643A REV A
              Dryer - Norge Dryer Model 7643A REV A (7643AREVA) Parts
              Norge
              7643A REV B
              Dryer - Norge Dryer Model 7643A REV B (7643AREVB) Parts
              Norge
              7740A
              Dryer - ELECTRIC DRYER
              Norge
              7741
              Dryer - DRYER
              Norge
              7741A71
              Dryer - DRYER
              Norge
              7743A
              Dryer - DRYER
              Norge
              7743A REV A
              Dryer - Norge Dryer Model 7743A REV A (7743AREVA) Parts
              Norge
              7744A
              Dryer - ELECTRIC DRYER
              Norge
              7745
              Dryer - DRYER
              Norge
              7745A71
              Dryer - DRYER
              Norge
              7745A77
              Dryer - DRYER
              Norge
              7748A
              Dryer - ELECTRIC DRYER
              Norge
              7749
              Dryer - DRYER
              Norge
              7749A71
              Dryer - DRYER
              Norge
              7749A77
              Dryer - DRYER
              Norge
              7750A
              Dryer - ELECTRIC DRYER
              Norge
              7751
              Dryer - DRYER
              Norge
              7751A71
              Dryer - DRYER
              Norge
              7751A77
              Dryer - DRYER
              Norge
              7761A-71
              Dryer - LNC DRYER
              Norge
              7761A-77
              Dryer - LNC DRYER
              Norge
              8433A
              Dryer - GAS DRYER
              Norge
              8433A REV A
              Dryer - Norge Dryer Model 8433A REV A (8433AREVA) Parts
              Norge
              8543A
              Dryer - GAS DRYER

              Get in touch, we're here to help!

              Open until 1am EST

              Contact Customer Service