Off-Switch Actuator Kit W10342596

Hello Bob, Thank you for your inquiry. This part is only sold as part of the kit. Hope this helps!

Hi Todd, Thank you for the question. This sounds like an issue with the Off-Switch Actuator Kit, PartSelect Number: PS3489806.The off-switch is used to supply power to the motor to initiate the compaction cycle. Check to see if the off switch has been damaged, and that it is working properly. However, if the switch is damaged, or will not stop the cycle when the button is engaged, the off-switch will need to be replaced. Hope this helps!

Hello Jeff, Thank you for the question. Checking the door panels there is no other parts that woudl attach or fit into the hole. Looks like it is for the Plunger. Thank you for your inquiry, good luck with this repair!

Hi Mike, thank you for your question. You may want to check your directional switch, off switch, safety switch, and the drive gear kit as well. I hope that helps. Good luck with your repair.

Hello Bill, thank you for your question. If the start switch, drawer switch and direction switch have been tested and are showing continuity, I would recommend testing the motor itself next. Drive Motor PartSelect Number: PS3652693. I hope this helps!

Hello Mark and thank you for writing. Yes, it certainly should. We hope this helps. Please contact us anytime if you require further assistance.

Hello David, Thank you for the question. Here is a repair story from a previous customer that may help. "Repair entailed removing the trash compactor from its installation position, removing the recess cover and machine front, disconnecting and removing the old actuator switch, drilling holes in the machine front, attaching the new actuator assembly, and disconnecting and reattaching the foot pedal." If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

Hi Larry, thank you for contacting us. Based on our understanding of the issue, we would suggest you check the directional switch, part number PS11744742, and the drive gear kit, part number PS398589. We hope this solves your problem!

Hello Susan, thank you for writing. From what you describe, it sounds like you need to install all the parts from the kit. This may make it function properly. You may also want to consider checking and possibly replacing the Directional Switch part PS11744742 or the Drive Gear Kit part PS398589 for your model. We hope this helps.

HI Todd, Thank you for your question. You mentioned in your original question to us that when the compactor is on it begins it cycle every time I close the door and then fails to stop. If your trash compactor keeps running after the cycle is complete, the problem may be with the top limit/directional switch assembly. The top limit/directional switch is a multifunction switch located at the top of the unit, and is activated by a metal tab on top of the ram. The directional switch is used to reverse the motor rotation and the travel direction of the ram. The top limit switch is often part of the directional switch and is used to automatically stop the motor when the ram reaches the top. If the top limit/directional switch contacts fail the motor may not stop at the completion of the cycle and will continue to run. To check for a defective switch, remove the unit from the cabinets and disconnect the power. Remove the mounting brackets and then the top panel. Inspect the switch actuating lever to ensure that the tab on the ram makes contact at the top of the ram’s travel. Remove the ram using caution not to damage the directional switch lever. Remove the switch and the wires from the switch terminals and check for continuity with a multi-meter. The top limit switch should have terminals marked C for “common” and NC for “normally closed”. You should see continuity between these two terminals without depressing the switch lever. With the lever depressed, there should be no continuity. You may require the electrical schematic for your model to determine the proper switch terminals to check. If you checks indicate otherwise, then you will need to replace the switch and verify the proper adjustment for the activating lever. You also may have a defective start switch. The start switch is used to supply power to the motor to initiate the compaction cycle. The switch may be a rotary, push button, or rocker style, and is located on the control panel or inside the drawer opening on foot pedal operated models. The switch uses momentary contacts that close to start the motor and then spring back to open the contacts. If the contacts weld or stick closed, the motor may continue to run after the cycle is complete. Check the start switch for continuity with a multi-meter. To determine if you have a defective switch, first locate the fuse or breaker and turn off the power. If your model uses a control panel mounted start or run switch, remove or lower the panel to expose the rear of the switches. You may have to pull the compactor partially out of the cabinets to do this. If your model uses a foot pedal operated switch, you will need to remove the unit from the cabinets to access the start switch and actuator. Using the wiring diagram for your model, determine the switch terminals to test and remove the wires from the terminals, usually marked C and NO. In the normal or resting position the switch should show no continuity. Only when rotated or depressed to the start or run position, should the switch then show continuity. If the switch shows continuity at all times, then it needs to be replaced. On foot pedal operated models, make sure that the actuator is not stuck and holding the switch closed. I hope this helps. Thank you and have a great day!