This replacement start switch is a genuine OEM part for your dryer. If your dryer will not start or shut off, you may need to replace this part. For this repair you will need a number 2 Phillips screwdriver and a pair of needle nose pliers. Disconnect power to the dryer before beginning this repair.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Douglas G - February 7, 2018
Verified Purchase
Easy to install
The part came in very good condition. The delivery was very fast, and it is working perfect!
★★★★★
★★★★★
Frank O - September 29, 2018
Verified Purchase
Dryer would not start
The part was exactly what I was looking for. The directions were really not needed and I was able to use my dryer within 10 minutes of receiving it. Thanks
★★★★★
★★★★★
Michael V - September 27, 2018
Verified Purchase
Replaced rotary start switch
Without Parts Select finding the part would have been the hardest part of the job, which was a very easy installation. Thank You Parts Select ! MCV
★★★★★
★★★★★
Robert L - October 2, 2021
Verified Purchase
Rotary start switch
Easy to install and works great I’ll be back
★★★★★
★★★★★
Lloyd St. R - February 7, 2018
Verified Purchase
Easy Repair
Order the part and changed in about 5 minutes.
★★★★★
★★★★★
Cheryl S - September 7, 2019
Verified Purchase
worked as expected
this part was easy to replace and the dryer is now working
★★★★★
★★★★★
Ronald C - September 10, 2019
Verified Purchase
Great Buy
Exactly what I needed. Worked perfectly. And was a good price.
★★★★★
★★★★★
David N - April 15, 2020
Verified Purchase
20 min job!
The part arrived quicker than expected and it took about 20 min. to install. great service. The web site makes it easy to find the part needed. I will definitely use PartSelect again.
★★★★★
★★★★★
Brad M - September 19, 2019
Verified Purchase
easy repair
Part was packed great. Good service
★★★★★
★★★★★
Jerry H - September 18, 2019
Verified Purchase
Easy fix
Remove 4 torx screws pop out old switch install new one , replace your torx screws. Tell your wife your dryers ready
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 4.4 / 5.0, 61 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Two knobs fell off and into area behind control panel.
First and foremost- unplug appliance or de-energize circuit breaker!!! This appliance runs on 240 volts!!
Removed back of control panel with multi tip screwdriver. I then pulled wire connections off of old knob one by one, installing on new knob before proceeding with next wire removal. Did this for both start knob and tem
... Read moreperature control knob. Once wires installed on new control, it was time to resecure to back side of control panel. There are tabs on the plastic that fit into the body of the controller, with a "leg" that fits under another tab to prevent the controller from moving when turning the knob. It may take a couple tries to get it secure. It did for me. Replace back metal on control panel, plug it back in or re-energize the breaker and done. FYI- one of the wires had shorted out when the controller fell into the recess behind the control panel. I was able to put a new connector on it with a crimp tool. Replacement connectors and crimp tool are available at most hardware and home warehouse.
The rotary start switch was non functional and the control panel’s raised plastic rear snibs behind the switch were broken had broken
I followed exactly the video instructions for installing these two items , using my iPad at the place of repair, and the work was completed easily and quickly
Clip holding the start switch on the backsplash broke and the start switch shorted out
I opened the back of the dryer to figure out what went wrong. Then I ordered the parts after looking them up on the website and spoke with a wonderful person who helped me be sure I got the right parts. When they came I took off the clips for the old start switch and had to replace a clip (which I got at ACE hardware and they told me ho
... Read morew to crimp it on). I watched the video on the website which was very helpful.
I replaced the start switch and a new backsplash (all the other switches were fine), screwed everything back together and it all worked perfectly!
Just to say I am a Chiropractor, not a repair person and I'm excited it went so well.
Both the start switch and timer switch had become old and worn out.
After unplugging the unit, I simply replaced them, matching each replacement connector on the unit. It was actually nothing special and the replacement components being identical left out a lot of guesswork.
Gently pull off all knobs and put aside. Remove the panel screws using the star bit. Tip panel forward. Remove three wires from old switch and put them on same terminals on new switch. Use the screwdriver to gently pull up the old switch's locking arm from the slot in the front panel and rotate the old switch until it pops out of the fron
... Read moret panel. Insert the new switch into the panel and rotate until the locking arm clicks into place. Replace front panel making sure no wires are pinched. Re-install the front panel screws and control knobs.
Read less
Douglas from ETOWAH, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Start switch was stuck in the on position internally. By the way this is for a gas dryer not listed in your appliance type
Un plugged dryer from wall - pulled off knob - Unscrewed 4 screws on top of panel - Opened panel by pulling it forward - Removed 2 leed wires - removed switch by turning switch counter clockwise - installed new switch put the wires back on and screwed the panel back on. Done deal.
Frederick from ROYAL OAK, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer did not turn off when the door was opened and then closed.
Followed your video instructions and it worked exactly as described. You will be my source for all appliance repair parts.
Robert from SOMERSET, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer wouldn't start
Unplugged the dryer. Removed the 4 star headed screws with a screwdriver. Tilted the console forward and lifted. I didn't have to slide mine to the right. Pulled the knob straight off the front of the console. Lifted the lock tab with the needle nose pliers and twisted the switch to the right. It popped right out. Pulled the wires off wit
... Read moreh the pliers. Be aware, there are three wires, two red and one black. The both red wires only connect to one terminal on the switch. It looked at first glance as if I had the wrong part. But those two wires are connected to each other so it was correct. Plugged those wires back on. Put the switch into the hole and twisted it back into place, the lock clicked in to place. Replaced the console and plugged it back in and it worked perfectly. Turned right on. This took me under 15 minutes to do. Steve is the man! This girl has been able to use his videos to repair the dryer 3 times, the washer once, and my dishwasher 3 times over the years!!
Read less
CHERI from CREEKSIDE, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rotary switch would stick on
Unplugged dryer. Removed four back panel screws to expose the switches. Removed the wires from the bad switch and transferred them to the new switch. Lifted locking tab on switch and rotated it so the two locking tabs aligned with the slots. Removed old switch and inserted new switch. Rotated about a half turn and replaced the four panel
... Read morescrews. Plugged in the dryer and tested. Very easy repair.
Read less
David from METAMORA, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
on /off switch would not work
remove 3 screws from back of top panel unplug wires from back of switch and twist out switch and replace same reassemble panel and plug it back in
Robert from WOBURN, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
37 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeremiah
September 15, 2017
I am replacing the rotary switch but I can only find two wires. The double red that comes from the timer and another that comes from the cycle select. Where is that third wire supposed to come from?
For model number DHDSR46GG1WW
Hi Jeremiah,
Thank you for the question. Here is a video on how to replace this switch. It should be helpful with locating the wires.
https://www.youtube.com/watch?v=m9lGqnfwLh4
Hope this helps!
17 people found this helpful.
Was this helpful?
Thank you for voting!
Kenneth
April 14, 2018
I need the panel that the switches snap into but i don't seem to be able to find it on your site the tab has broken off so it won't hold the start switch
For model number Model DBXR463EG0WW
Hello Kenneth, Thank you for your inquiry. We're showing that they snap into the plastic tabs on the inner part of the backsplash-part# WE19M1490-white, or part# WE19M1491-bisque. Hope this helps!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Gasman
May 5, 2018
When i try to start the dryer you here the dryer turn on for 1 second.When i let go of the start dial the dryer turns off.For that one second the tumbler does not turn
For model number dbxr463gd3ww
Hello Gasman, thank you for your question. There are a few parts you will want to check first. The Drive Belt Part Number: WE12M29, and the Idler Pulley Wheel Part Number: WE12X83 that the belt rides on, as well as the Rotary Start Switch Part Number: WE4M519, Interlock Switch Part Number: WD21X10261 as well as the Door Switch Part Number: WE4M415. These parts can be tested with a multimeter to determine if they are bad. I hope this helps!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Susan
November 13, 2018
When i turn the rotary start knob on my dryer it starts but once it is released it stops. Do you think the knob is the problem or is it likely something else??
For model number DWSR483EG3WW
Hello Susan, Thank you for the question. The knob is just used to give you something to hold and grip. It sounds like an issue with the switch behind the knob. Part Number: PS3487203. Hope this helps, good luck with this repair!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
February 21, 2018
I changed the switch but the dryer will not keep running unless you hold the switch to the start position
For model number Gtdx200gm1ww
Hi Robert, Thank you for the question. This would be an issue with the switch on the motor. The switch is not sold separate from the motor so the motor will need to be replaced, PartSelect Number PS11699355. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Nancy
October 14, 2017
Will this work on Hotpoint dryer
For model number dbxr463ed2ww
Hello Nancy, thank you for contacting us. Based on the model number provided this would be the correct start switch. Good luck with the repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Nikki
August 26, 2017
Okay so i purchased the rotary start switch and as i tried to remove the 3rd wire i see that there is some sort of Green rust on it that's making it hard to remove from the defective rotary switch. What is that Green rust that is on the electric wire?
For model number DBSR463EG1WW
Hello Nikki, thank you for contacting us. That green rust would be corrosion. Over time that can build up, you can get some spray to remove and clean it. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Thomas
January 4, 2019
Can I check this part by using a hand held multi-meter, not sure what needs replacement??
Hello Thomas, Thank you for the question. Yes, you can test with a multi meter to check for continuity. Hope this helps, good luck with this repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Jim
June 28, 2019
Is there a way to 'test' the start switch? I was thinking i could bypass with a quick touch of hot wires to see if the dryer motor starts. Your thoughts please.
For model number DBSR463EG7WW
Hello Jim, Thank you for the question. Yes, you can test with a multi meter to check for continuity. Hope this helps, good luck with this repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
David
January 28, 2019
This switch i received from you {# we4m619 } has 3 electical post and my switch has 2 post . I have 2 two brown wires on one spade and a 1 wire on another. This one you sent me has 3 elec. Post i only have but only two hook ups the switch i have is normaly open the one i got from you i don't think it is, mine i have to turn to start and it stays engaged on start.
Hi David, thank you for your question. We do have an installation video for this part that may help: https://youtu.be/m9lGqnfwLh4. If you do not have a third wire to connect to the switch then you may not have to worry about that. Install the wires that you do have on the same terminals as your old one and it should work. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3487203
Manufacturer Part Number: WE4M519
