Quick Question!

Have you ever purchased from PartSelect.com before?

345337-1-S-Whirlpool-3394652           -Multi Rib Belt
345337-1-S-Whirlpool-3394652           -Multi Rib Belt 345337-2-S-Whirlpool-3394652           -Multi Rib Belt 345337-3-S-Whirlpool-3394652           -Multi Rib Belt https://partselectcom.azureedge.net/Schematics/Whirlpool/DHKQOZSM.gif

Multi Rib Belt

Your Price

Order within the next 3 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS345337
Manufacturer Part Number 3394652
Manufactured by Whirlpool

Specifications: Length 79-1/8 inch, width 1/4 inch, 4 ribs, Flat.

This part works with the following brands: Kenmore, Whirlpool, KitchenAid, Roper, Crosley, Amana.

This part works with the following products: Dryer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Will not tumble.
  • Noisy.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.4 / 5.0, 4 reviews What's this?
1-4 of 4

13 of 18 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Socket set
Customer: William from Glen Burnie, MD

In the middle of changing loads there was snapping and sound and drum stopped turning.

I was hopeful it was the belt. But, I had no idea how to get to it. I used the model no. and looked on line for pats and schematics. That gave me a sense of what to do. I started at the rear and removed the back panel. It was like peeling an onion because then, I wasn't sure what to remove next. So I just kept removing nut head screws until eventually I had loosened the sides, removed the top and discovered the front lifted up and off (no screwed attachment.) There's grounding wire that must be detached. Don't forget to re-attach. Without proper grounding you could be electocuted! I was careful to remember how it was attached. To get to the pulley, which is on the front, I had to remove the drum. I found the snapped belt. The pulley is held in place by tension from the belt so, once the belt goes the pulley detaches. I tried to find the belt locally the following week but was unsuccessful. I found the part on-line and had it in four days. It was tricky getting the belt and pulley in place. I persevered.
The parts ( I replaced the fliter that needed replacement for years too) came with installation instructions. Its possible I did not have to disassemble as much as I did. Oh well! Although I'm fairly mechanical, I'm still pretty proud to have been able to do it and save the cost of a repairman.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 9 people found this instruction helpful

Parts Used:
  • Multi Rib Belt
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Pliers, Screw drivers, Wrench (Adjustable)
Customer: William from Burlington, WA

Dryer was rumbling and clanking

My dryer started making a loud rumbling and clanking sound and I didn't know what was wrong.

First I pulled it away from the wall and disconnected the power cord. I loosened the four nut/screws across the top of the rear of the dryer with my adjustable wrench then removed them with the flathead screwdriver. Then from the front of the machine, pulled the top of the dryer towards me, freeing the top and removed it. I could see one belt towards the front of the machine that appeared to be intact. I plugged the dryer back in and ran it... It spun but continued to clank and rumble. I noticed a "groove" near the rear of the drum and didn't see a belt there so I assumed that I needed the rear belt and ordered a replacement. I WAS WRONG. It turned out that there is actually only ONE BELT on this machine, that in fact I needed replacement DRUM WHEELS.

Next, I unplugged the power cord again and then I removed all twenty some-odd screws from the rear of the machine... which was POINTLESS as it only gave me access to the heating element, so I replaced this and all the screws.

I then removed the inside top nut/screw from the front panel on both the right and left inner lip. The panel then lifted up and off of the machine...only connected at this point to the rest of the dryer by the wires.

I made a schematic of the wires and which color was connected where, and then only removed those that were necessary to detatch the front panel completely from the dryer (so I could easily replace them properly later).

I noticed at this point that the belt was still functioning (although was cracked and needed replacing soon anyways)...but that the bottom drum wheel had worn itself down on the inside (where it rests on the axle)...the rubber around the outside was still good... but the whole wheel needed replacing. The side drum wheel (same part number as bottom) appeared to be fine.

I ordered replacement DRUM WHEELS (they sell them in packages of two only).

When the wheels arrived, I got down on my hands and knees and noticed how the belt was connected to the drive spindle of the motor... by a spring levered plastic wheel... very simple. Push the spring lever towards the drive spindle of the motor...loosening the belt. Then removed the belt from the motor, relaxing the spring and the belt came off, hanging only around the drum of the dryer.

Without tension on the spring levered plastic wheel, it came off of the bottom of the dryer completely. (If your belt has broken, you most likely will find this sitting on the bottom of your dryer...I will tell you how to attach it later on in this story.).

I carefully pulled the sides of the dryer case apart and slid one side of the drum forward out of the case...then slowly slid the other side of the drum out of the case...gently lifting up and out...completely removing the drum from the machine....setting it aside.

The dryer (inside the case) was FILTHY. I got out the handheld vacuum and cleaned it all out (finding a religous medallion, an earring, and over $2.00 in change). I vacuumed the inner bottom, sides, motor, and took advantage of vacuuming the inside of the lint collector as well... cleaning it up nicely.

The bottom drum wheel was attached by a triangular plastic clip (on both sides of the wheel)...I removed the plastic clip carefully by gently prying it off with the flat edged screwdriver... being careful not to break it. There was a LOT of hair wrapped around the axle near the triangular clip and used the pliers to pull the hair off...then removed the bad wheel..then the plastic clip behind where the wheel was sitting...and the hair there as well. I cleaned off the axle thoroughly, then did the same with the other drum wheel (even though it looked fine, I replaced them both.).

I set the old side wheel aside with the old (still useable) triangular plastic clips. In the future if one of the wheels goes bad... I'll have a replacement that will get me by.

Then I slid one of the NEW triangular p

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
  • Multi Rib Belt
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Kenneth from Gerber, CA

Drum stopped turning

First unplug dryer, then remove 4 screws along the back of the top and remove top and set aside. Next pull outward on the front until the front clears the drum and lift off the front and set to the side, careful not to stretch the wires to the door switch. Remove old belt and slip belt around the drum and line up with marks from old belt. Reach in under the drum under the motor and lift up the tensioner. Insert belt through tensioner and slip over the front of the shaft on the motor and release the tensioner. The belt should now be tight. Reinstall the front and top, plug in and test.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 8 people found this instruction helpful

Parts Used:
  • Multi Rib Belt
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Customer: Dorise from Donalsonville, GA

A broken belt

my hany man did it....

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-4 of 4

Model Cross Reference

This part works with the following models:

PartSelect Number: PS345337
Manufacturer Part Number: 3394652
Brand Model Number Description
Kenmore110088732791Washer Dryer Combo
Kenmore1101820296Washer Dryer Combo - LAUNDRY CENTER