Water Inlet Valve with Mounting Bracket Specifications
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
No hot or cold water | Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Whirlpool, Kenmore, KitchenAid, Roper.
Part# 285805 replaces these:
AP3094541, 868761, 285805, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673
...
Show more, 8228, 99989697, W10110517
Show less
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
57 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jacob
July 20, 2017
So when I looked through you side about slow water coming in (cold) to my washer you suggested I clean them, which I did. It worked for a little while and now its back to slow. I checked the water valves and the screens and they are clean. What should I do next? Just give up and buy new ones?
Hi Jacob, if the screens are clear then it sounds like you need to replace the water inlet valve 285805. I hope this helps!
37 people found this helpful.
Was this helpful?
Thank you for voting!
Paul
July 20, 2017
Little or no hot water into machine, cold is ok. Screens in hose is clean.
For model number KAWE560WWH0
Hello Paul, If you've checked the screens, and if the inlet hoses are not kinked or obstructed you will might have an issue with your water inlet valve circuit. This valve has two solenoids that operate inlets for both the hot and cold water. You can test solenoids for continuity with a multi-meter. If the solenoid has no continuity is faulty. These solenoids are normally not available separately so you will need to replace the complete valve. Make sure you shut off the power or unplug the appliance before performing this test. I hope this helps!
27 people found this helpful.
Was this helpful?
Thank you for voting!
Tom
November 9, 2017
Washer doesn't fill with any setting, cold,warm. Hot. I know the the supply to the machine is okay. Fyi i can set the timer to spin and that cycle works the timer advances. Any suggestion on which is the cause. Thanks
For model number LSQ8520JQ0
Hi Tom, Thank you for the question.If you've checked the screens, and if the inlet hoses are not kinked or obstructed you will might have an issue with your water inlet valve circuit. This valve has two solenoids that operate inlets for both the hot and cold water. You can test solenoids for continuity with a multi-meter. If the solenoid has no continuity is faulty. These solenoids are normally not available separately so you will need to replace the complete valve. Make sure you shut off the power or unplug the appliance before performing this test. I hope this helps!
18 people found this helpful.
Was this helpful?
Thank you for voting!
Lottie
January 6, 2018
I have Kenmore top loading washing machine. When you turn it on, the water comes on and fills the tub, but does not shut off when its full and it keeps flooding the room. What is my problem?
For model number 11022632100
Hello Lottie, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: water inlet valve, water level switch kit with pressure hose, hose clamp, and the water pump. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!
12 people found this helpful.
Was this helpful?
Thank you for voting!
Harper
July 20, 2017
I turned my washer on today and everything seemed normal and I walked away but when I came back I noticed it is not filling up with water (cold), what should I check for first?
Hi Harper, we suggest checking the valve that allows the cold water into your washer. It could be at fault and not staying open to allow the washer to fill properly. Please let us know if you have any further questions!
12 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
January 18, 2018
Our washing machine has a persistent slow drip into the tub from the top when washing machine is not in operation. I assume this would indicate the need to replace the fill valve?
For model number LSR6132EQ1
Hello Mike, Thank you for your inquiry. I would also check the washers and hoses as well. Hope this helps!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Randy
November 5, 2018
Does this valve work for Kenmore model# 11082873800
For model number 11082873800
Hi Randy, thank you for your question. Yes, this is the correct water inlet valve for your appliance. I hope that helps. Good luck with your repair.
7 people found this helpful.
Was this helpful?
Thank you for voting!
Terry
August 26, 2017
Does this part fit Whirlpool washer model # ghw9400pt0?
For model number GHW9400PT0
Hi Terry,
Thank you for your inquiry. The part number for the correct water inlet valve for your appliance is PS11744913. I hope this helps. Thank you and have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Ashley
July 20, 2017
My washer is taking FOREVER to fill up!! Neighbor said to check and clean the water valves but how would I go about doing that? I know where to find them but I’m not exactly sure what to do with them???
Hello Ashely, you need to remove the hose that is attached to the faucet and the valve, and then you can access the screens to push them out. we suggest soaking them in hot water with a splash of white vinegar to give them an all over clean. Best of luck with this repair!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Amanda
December 30, 2017
My washer fills will water at the beginning of the wash cycle. It then washes the clothes and drains the water, but it will not fill with water again. It then continues to agitate without any water. It will also stop after the water is drained and I have to manually start the washer to fill it up with water again. What do I need to replace?
For model number LSR8233EQ0
Hello Amanda,
Thanks for your question. Check the pressure tube that connects from the water level control to the tub. It may be obstructed and should be cleaned. You may also want to test the water inlet valve with a multi-meter to ensure it has continuity, and replace it if it does not show continuity. If those parts are intact, consider replacing the timer.
I hope this helps.
Hot water connection was stripped and couldn't connect water line to washer
Unplugged it. Removed the two screws holding the panel on. This model had the screws on the front. Unplugged the wire harness and tipped the control panel back. I popped off the clips for the cabinet and slid it off the frame. On the back of the washing machine, I unscrewed two screws that held the water inlet valve in place. I unhooked the two wire harnesses on the inlet valve. Slid the clamp on the small hose back and pulled the hose off the inlet valve. Once I had the old part off, it was just a matter of doing it all in reverse. I did have to screw the metal plate that came with the part onto the part before I installed it. I put the small hose onto the new inlet valve and slid the clamp back in place on the hose. Put the new valve through the holes on the back of the machine, and replaced the two screws. Click the two wire harnesses back on, making sure to put the RED harness on the HOT valve (the holes have the stamp H and C on the back of the machine itself. Slid the cabinet back into place. Put the wire harness back on. Replaced the cabinet retainer clips. Slid the control panel back into the slots and replaced the two screws for it. That was it. All told it took me 15 minutes total. This was an extremely easy repair.
CHERI from CREEKSIDE, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing water inlet valve with new one
The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her)
David from HENRY, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When washer was in cold water rinse cycle, loud squealing noise.
unplug unit first Took water & drain hose loose, used two wheel dolly, took washer out on patio. Removed water hose. Removed two screws # 49 an laid back control unit then Removed 2 #6 Clips Top of unit, then pried back unit cover out enough to remove Water valve after removing #4 screw that holds unit to back panel ,removed hose clamp #21 an electric connections, install new water valve and put back together..DO NOT TAKE BOTTOM SCREWS FROM BACK PANEL, if so the bottom will drop.. Intake cold water valve was half stopped up. Also new water lines.
James from LEXINGTON, KY
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water would not stop filling out the tube.
1- Remove power connection, remove water connections. 2- Remove the top controller box and free it from its hinges. 3- Loosen the back cover to get access to water valve assembly. 4- Remove hose clamp connected to inlet water valve. 5- Remove the old water valve which is secured with 1/4" screw. 5- For installation perform step 5 to 1 and then test your Installation.
GEORGE from WEST HILLS, CA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water would not shut off
Shut off both water valves and used a cup to catch water from hoses. Removed top control panel that's held on with 2 phillips screws. Remove top screws on the back to gain access. Was able to access the valve by pulling slightly out on the top corner.
Patrick from RUSSIAVILLE, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking valves
We watched a video on YouTube; it was very easy . We had to use the mounting bracket.
Connie from BATON ROUGE, LA
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water inlet valve bad
received valve as ordered a simple installation. everything went well.home owner can do this repair
linville from lily, KY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
1. No hot water and cold water filled very slowly. 2. Washing machine severely vibrated and was very noisy.
I got a few hints from YouTube (how to remove the washing machine casing) and rest was very simple
Wayne from ZEPHYRHILLS, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
131 Reviews
4.6
Filter By Rating:
5 Stars
98
4 Stars
24
3 Stars
5
2 Stars
1
1 Star
3
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Esther C - June 14, 2023
Verified Purchase
So far, so good!
My washing machine is back in working order. Thanks!
★★★★★
★★★★★
John F - March 15, 2023
Verified Purchase
Easy repair
Replaced 20 year old water inlet valve and now no more unexpected water over flows. Very easy site to order from, fast shipping and good online instructions. Amazing to still be able to get parts for an old machine. Not eager to buy new washer which are not as quality built these days. You guys are a life saver and wife is happy. Thanks
★★★★★
★★★★★
Rick B - January 16, 2023
Verified Purchase
Saved hundreds!
Very simple installation. Just follow the steps on the video and you won't have a problem.
Didn't realize how clogged the valves were until i did my next wash.
★★★★★
★★★★★
Antonio H - January 12, 2023
Verified Purchase
Easy Repair
This all it took to revive the ole washer. It was leaking at the inlet valve. Got it replaced; leak no more! Water pressure back to normal. Thank you
★★★★★
★★★★★
Micheal P - August 31, 2022
Verified Purchase
Decent price
Pros- I was able to find the part easily, the price was decent, the video was very helpful, and the part fit.
Cons-This is the second time I replaced this valve in the past 1 1/2 years. I am hoping this one lasts longer than the last one. WHereas the part is fairly straightforward to replace, I have to pull the washer out of the hallway to be able to allow for repair so it is not a simple repair in this case.
★★★★★
★★★★★
Dennis O - July 15, 2022
Verified Purchase
Work as Expected
The part was exactly what I needed and functioned correctly. The installation tutorial video provided eliminated guess work on how to correctly remove and replace the part. Thank You PartSelect!
★★★★★
★★★★★
James G - June 10, 2022
Verified Purchase
easy repair;
part installed in 10 min. Can't get any easer
★★★★★
★★★★★
Paul M - June 9, 2022
Verified Purchase
Old washer works like new!
As always, the diagnosis was spot on and the installation video was VERY helpful. The washer was taking forever to fill and was not turning the water off all the way when it did finally fill. My well pump had drawn sand into the lines and partially clogged the valve. I cleaned out the trap, but some sand may have been drawn in further than I could reach and may have damaged the valve. Having opened up the washer many times before, the repair took less than 30 minutes from start to finish. Now the tub fills much more quickly and the water shuts off when it should.
★★★★★
★★★★★
Sheryl S - May 16, 2022
Verified Purchase
Great part
Was the perfect solution to our issue. Received part promptly and was a snap to replace. Thanks
★★★★★
★★★★★
Deborah P - April 22, 2022
Verified Purchase
Washing machine part
I was pleased with it’s arrival and how quick I could get my washer running again. Thank you
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS334646
Manufacturer Part Number: 285805
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
Same-day Shipping
Ships from USA
1 Year Warranty
365 Day Returns
