This agitator cam kit contains an almost three inch white retainer and four agitator dog ears. This kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover).
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not agitate
This part works with the following products:
Washer Dryer Combo, Washer.
This part works with the following products:
Kenmore, Whirlpool, Maytag, Crosley.
Part# 285751 replaces these:
AP3094521, 2837, 285751, 3351019, 387092, 3947410
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
4.8
Filter By Rating:
5 Stars
3
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Michael R - October 23, 2019
Verified Purchase
Repair broken agitator cam
The Agitator Cam Kit came with 3 dogs and should have had 4, but it worked with 3.
★★★★★
★★★★★
Timothy N - September 25, 2019
Verified Purchase
Best Source for Parts
Original parts! Made repair a breeze!
★★★★★
★★★★★
Tim D - August 6, 2019
Verified Purchase
Washing machine
Got on time and it was as advertised. Machine up and running
??????
★★★★★
★★★★★
Jerry S - March 5, 2019
Verified Purchase
Worked out fine and the noise went away. Plenty of videos on how to do it avaible.
Fit perfect and does what it should. No problem installing it either. The parts diagram make it easy to find the correct part and no problem ordering.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 25 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Agitator moves in both direction.
Open lid,remove softener cover on agitator[grip and pull-up gently] [inside] grip and pull-up on softener dispenser cap with seal,you see the bolt,fit a 7/16 or a 11mm socket on your extension and remove the bolt,reach in and lift unit out gently,place on workbench/area or floor and gently but firmly remove top portion then with thump and
... Read more index finger push out on the two small tabs[or one at a time]to reliese the agitator.[broken dogs inside,remove and clean]a small rubber "O"-ring is below,replace with a little silicone grease to keep in place and on the contact surface and metal spline for the agitator.place all four dogs in the kit[hold up-side down{dogs will not fall out}sliding top portion over and lock in the two tabs.you are now ready to reassemble.
Read less
DONALD from BROOKLYN, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Will not spin.
Whirlpool Thin twinn washer dryer combo, removed acces cover on top of washet then removed the two retaining clips from the back corners of the unit then removed the top of the washer. Used a socket to remove the two screws on the top inside of the front cover and one screw from the angle bracket on the top left front then removed the fro
... Read morent cover. Laid the unit on its back then remove the two pump retainers then removed the pump then pined the pump out of the way,unpluged the power connectoer from the motor and removed the wire harnes from gear box in put it out of the way, removed the retaining clips for the motor the removed motor, found the drive coupler to be broken so replaced itwith the new one and reassebled in reverse to disassembly. Works like a champ.......
Popped the agitator cap with a flathead screwdriver. Removed the dust cap, tearing the o-ring in the process. Removed the bolt that holds the agitator in place, removed the whole agitator. Pulled the top portion of the agitator off, removed the dog housing and all pieces of the broken dog pieces. Replaced them, and put it all back tog
... Read moreether in reverse order. Pretty straight forward repair. Works great!
machine would not agitate properly and NOISY Dryer
took off fabric softener dispenser. used socket to remove agitator. Cleaned and then replaced the little plastic dog ears...works like brand new! It took 15 minutes or less.
Also repaired noisy dryer. replaced drum rollers, pulley and belt. The job took about an hour and was real simple. However..the dryer was still noisy. Fixe
... Read mored with a prybar to force drum to be tighter. It now sounds like brand new.
Easy Repair!! Remove the Fabric Sofetener dispenser from the top of the agitator. Beneath that, remove the plastic cover over the cam assembly. Use an 11mm socket to remove the agitator. After removal, pull it apart to reveal the cam. simply replace the dogs and reverse the process to reassemble. NOTE: YOU MAY NEED A LONG SOCKET EXTENSION
... Read more TO GET DOWN INTO THE 11mm BOLT.
Read less
William from Thermopolis, WY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper agitator would not agitate.
The cam kit itself did not fit. However, the dog ears could be swapped out. It's cheaper to buy the set separately, they're fairly universal. Part number: PS388034
jon from jax, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
upper agitator wouldn't move
pop the cap off the top of center agitator unit, remove one 11mm bolt and remove unit from washer. take apart, remove & replace broken dogs and reassemble. I actually bought the wrong kit, my cam is much longer but since the problem was caused by the broken dogs it did not matter.
Brian from Staunton, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator gears stripped out
First I removed the fabric softener cup then the cover with seal. I then used an 11mm socket to remove the bolt, pulled up on the agitator cam removed the old gears and replaced with new ones. Put it all back together and it Works great
Nathan from Bellingham, MA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitor cams wore out
I ordered a new part based on the exact model number and was sent the wrong part. Fortunately the cam dogs were the same size so I was able to re-use the original housing and throw the new one away.
Merlin from Scott, LA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
aggitator stripped, not turning
removed the cap and unscrewed locking fitting. Removed aggitator dogs and replaced with new and reassembled.
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
September 21, 2023
With the washer door open AND door safety switch depressed. The spin cycle will only work when I press down on the agitator. If not depressed the agitator will only hit and miss.
For model number LTG6234DQ1
Hello Bob, thank you for contacting us.Based on the understanding of the issue, we would recommend checking the agitator bolt, part number PS11741866, to fix the issue. We hope this helps!
This is the cam kit that I have and I took it apart to clean but when putting it back together the agitator dogs falls out of place because theirs nothing holding them in the cam is there something I'm missing?
For model number Ywet3300xq2
Hello Dylan, thank you for reaching out. According to our research, the issue is most probably with the agitator cam. It holds the agitator dogs. We would recommend replacing the agitator repair kit, part number PS334624, to solve the problem. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
![](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/346995-1-S-Whirlpool-341241-Multi-Rib-Belt-92-1-4-amp-quot.jpg "Multi Rib Belt - 92-1/4" – Part Number: 341241")
