Agitator Cam Kit 285751 | Official Whirlpool Part | Fast Shipping | PartSelect
Agitator Cam Kit – Part Number: 285751
Agitator Cam Kit – Part Number: 285751 Agitator Cam Kit – Part Number: 285751 https://partselectcom.azureedge.net/Schematics/Maytag/TEBJZIYW.gif

Agitator Cam Kit

Product Description

Agitator Cam Kit Specifications

This agitator cam kit contains an almost three inch white retainer and four agitator dog ears. This kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover).

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Will not agitate, Noisy.

This part works with the following products:

Washer Dryer Combo, Washer.

This part works with the following brands:

Kenmore, Whirlpool, Maytag, Crosley, Amana.

Part # 285751 replaces these:

2837, 285751, 3351019, 387092, 3947410, AP3094521.
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 25 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Nathaniel from Kennesaw, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Parts Used:
285751
Top half of agitator didn't agitate
First I removed the fabric softener container and set it aside. Below that, there is a plastic cover with a rubber gasket that distributes the fabric softener. I also just pulled that out and set it aside. Below that was an 11mm bolt that attached the upper and lower agitator to the drive mechanisim. The lower agitator is attached directly to the shaft and that was working properly so I knew it was't a motor or drive issue. Until it broke, the top half of the agitator sat still for a second, then it turned clockwise with the lower agitator. This helped push the clothes down to the lower part to be circulated throughout the wash cycle. Well, now the upper agitator just sat there, like it wasn't attached to anything at all. Below the aforementioned plastic cover with the rubber gasket, I found a part that had 4 plastic "teeth" that moved in and out, releasing and grabbing the inside of the upper agitator, respectively. Over time, these teeth wore down and stopped "grabbing" the ridges on the inner part of the upper agitator, causing it to stop turning with the lower agitator. I removed the 11mm bolt and tried to seperate the upper agitator from the lower agitator to replace the teeth. This part was kind of tough to get out because the plastic clips that held it in were deformed. I just had to pull hard and eventually it came apart. In the process, I broke two of the clips. I wasn't really concerned because the 11mm bolt holds everything in place anyway. After that I just swapped out the worn teeth with the new ones. I put it back together in the opposide order I took it apart and viola....good as new. And it only cost me $15 bucks.
66 of 73 people found this instruction helpful.
Was this instruction helpful to you?
David from Goodlettsville, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Parts Used:
285753A, 285785, 285751
machine would not spin
Disconnect electrical, took out agttator, tipped machine againest the wall. On hooked the two hoses on pump, removed three bolts pulled complete assembley out removed worn parts and installed new parts and reassembled. Works like new,
45 of 1233 people found this instruction helpful.
Was this instruction helpful to you?
Kevin from Everett, WA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
Parts Used:
WPW10074580, 285751
upper portion of 2-piece agitator didn't spin
Popped the agitator cap with a flathead screwdriver. Removed the dust cap, tearing the o-ring in the process. Removed the bolt that holds the agitator in place, removed the whole agitator. Pulled the top portion of the agitator off, removed the dog housing and all pieces of the broken dog pieces. Replaced them, and put it all back together in reverse order. Pretty straight forward repair. Works great!
34 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Brad from Boise, ID
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Parts Used:
285751
Motor was working and rotating lower portion of agitator, but the top was not spinning.
1. Remove the fabric softener receptacle

2. Remove the plastic dome shaped separator with a rubber o-ring around it (directly beneath fabris softener receptacle)

3. There is an 11mm bolt right in the center. Use socket wrench to remove bolt.

4. Remove agitator from washign machine.

5. Separate top half of agitator from bottom half (this was the most difficult part for me; unlike others who have described this repair, mine would not simply pull apart; I spent quite a while trying to pry up the white plastic clips extending from the bottom piece through the clear plastic piece that covers the "dog teeth" that make the top piece agitate)

6. Once apart, replace worn "dog teeth" with new dog teeth.

7. Put back together in reverse order.
21 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Robert from Brooksville, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
285751
Upper agitator did not rotate
Removed the rinse dispenser from Agitator. Unbolted and removed agitator from machine.
Directions said remove upper agitator by pulling apart. Had to brace bottom with both feet, and lift straight up. Came off. Replaced 4 cogs, re=assembled and re-installed.
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Hugh from Auburn, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Parts Used:
WP63594, 285751
aggitator stripped, not turning
removed the cap and unscrewed locking fitting. Removed aggitator dogs and replaced with new and reassembled.
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Brian from Staunton, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Parts Used:
285751
upper agitator wouldn't move
pop the cap off the top of center agitator unit, remove one 11mm bolt and remove unit from washer. take apart, remove & replace broken dogs and reassemble. I actually bought the wrong kit, my cam is much longer but since the problem was caused by the broken dogs it did not matter.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Nathan from Bellingham, MA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Parts Used:
285751
agitator gears stripped out
First I removed the fabric softener cup then the cover with seal. I then used an 11mm socket to remove the bolt, pulled up on the agitator cam removed the old gears and replaced with new ones. Put it all back together and it Works great
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Merlin from Scott, LA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
285751
Agitor cams wore out
I ordered a new part based on the exact model number and was sent the wrong part. Fortunately the cam dogs were the same size so I was able to re-use the original housing and throw the new one away.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Isaac from Bridgeport, CT
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Parts Used:
285751
Washer machine wouldn't turn
It was a really simple thing to do. Make sure to buy the agitator cam kit (a little piece broke when I was taking it apart). Take off the cover and then the nut that is underneath. Replace the agitator cam and that's it!!! Usually those agitators dog ears wear down with time so if the agitator assembly is not turning, check this first.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
2 Reviews
5
out of 5
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS334624
Manufacturer Part Number: 285751
Brand
Model Number
Description
Kenmore
110088732791
Washer Dryer Combo
Kenmore
1101820299
Washer Dryer Combo - WASHER DRYER LAUNDRY SYSTEM
Kenmore
11026182029A
Washer Dryer Combo - THIN-TWIN (WASHER/DRYER)
Kenmore
11080754000
Washer Dryer Combo
Kenmore
11080754001
Washer Dryer Combo
Kenmore
11080754003
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
11080754004
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
11080754006
Washer Dryer Combo - WASHER * DRYER LAUNDRY SYSTEM
Kenmore
11080764000
Washer Dryer Combo
Kenmore
11081422510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
11084417100
Washer
Kenmore
11084417300
Washer
Kenmore
11084417600
Washer
Kenmore
11084417700
Washer
Kenmore
11084417800
Washer
Kenmore
11084418100
Washer
Kenmore
11084418300
Washer
Kenmore
11084418600
Washer
Kenmore
11084418700
Washer
Kenmore
11084418800
Washer
Kenmore
11084419100
Washer
Kenmore
11084419110
Washer
Kenmore
11084419300
Washer
Kenmore
11084419600
Washer
Kenmore
11084419700
Washer
Kenmore
11084419800
Washer
Kenmore
11084419810
Washer
Kenmore
11084670100
Washer
Kenmore
11084670300
Washer
Kenmore
11084670600
Washer