Quick Question!

Have you ever purchased from PartSelect.com before?

334132-1-S-Whirlpool-279080            -High Limit Thermostat Kit
334132-1-S-Whirlpool-279080            -High Limit Thermostat Kit 334132-2-S-Whirlpool-279080            -High Limit Thermostat Kit 334132-3-S-Whirlpool-279080            -High Limit Thermostat Kit https://www.partselect.com/Schematics/Whirlpool/YCZOTVH1.gif

High Limit Thermostat Kit

Your Price

Order within the next 5 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS334132
Manufacturer Part Number 279080
Manufactured by Whirlpool

This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 225 degrees Fahrenheit. The element will kick back in when the temperature drops to 185 degrees Fahrenheit - the differential of 40 degrees.

This part works with the following brands: Kenmore, KitchenAid, Whirlpool.

This part works with the following products: Dryer, Washer Dryer Combo, Microwave Oven Combo, Wall Oven.

This part fixes the following symptoms:

  • No heat or not enough heat.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.8 / 5.0, 1 reviews What's this?
1-1 of 1

15 of 24 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: William from BURNET, TX

Dryer was getting hotter than blue-blazes, melted synthetics, damaged belt

Removed back of dryer, there were 3 screws on each side. There were two thermostats on the output vent and one thermostat on the heating element housing. Adjusted the temp settings on the thermostats per the instructions received with each thermostat (cross-refernece of original number required). Each thermostat had two screws and two wires. Terminals were coded "1" and "3," must get correct wires back in same place. The heating element thermostat required to splice new connector on one wire (per instructions enclosed with thermostat).. Easy as pie. BELT: Remove screws from lint screen housing, then pry up front of top of dryer and swing back (make sure you are next to the wall so it doesn't fall.) Remove the bottom front panel, remove the door tension springs, remove the two screws on the front of the front panel and remove the two top screws on the inside of the door panel (leave the door attached, but use tape to hold it shut so it doesn't hit you on the head) Careful of the door switch wire, carefully lean door up so it doesn't fall. The Drum will fall when front panel is removed, so have someone to help you hold it up. You do not have to remove the drum. With your frend holding the drum, go under and pull the tension spring roller back to slack up the belt and remove the belt from the tensioner and motor pulley. Remove belt from drum. Wrap new belt around drum (ribs down facing drum) and re-route belt around pulleys according to diagram in instructions (same way you pulled it off). I did it by myself, but I got konked in the head by the door, so be careful. Easy, but awkward. Watch for sharp sheetmetal edges.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-1 of 1

Model Cross Reference

This part works with the following models:

PartSelect Number: PS334132
Manufacturer Part Number: 279080
Brand Model Number Description
Kenmore1106310800Washer Dryer Combo