GE/GE_Thumb/00001739i04.gif
See part 269 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Icemaker Fill Hose Extension

★★★★★
★★★★★
2 Reviews

Rated by 3 customers 

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS298725
Manufacturer Part Number WR2X7927
Manufactured by GE
You May Also Need?
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Refrigerator.
This part works with the following products:
General Electric, Kenmore, Hotpoint.
Part# WR2X7927 replaces these:
AP2059766, 298208, WR02X7927
Questions and Answers

Be the first to ask our experts a question about this part!

Customer Repair Stories
 Average Repair Rating: 3.7 / 5.0, 3 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
The icemaker was leaking water into the freezer, causing the freezer to be covered inside with ice.
The actual repair was a snap. However, be sure you check to make sure all of the parts are there. The two electrical adapter/connectors were missing from the water valve package, so I could not complete the job until a new valve could be shipped. The two adapters are essential to proper operation of the water valve. New ones arrived in 3 days.

DISASSEMBLY:

1. Unplug the refrigerator.
2. Shut off the water supply to the icemaker.
3. Remove the screws holding the cardboard cover onto the lower back side of the refrigerator, using a nut driver.
4. Disconnect the water supply line from the top of the water valve.
5. Remove the screw holding the water valve bracket onto the back of the refrigerator.
6. Unscrew the two water feed tubes from the water valve (one goes to the icemaker and one to the cold water dispenser).
7. Pull the two electrical connectors straight out of the back of the water valve. They are color-coded, but it won't hurt to label them with a small piece of masking tape.

NOTE:

Since I wanted this to be fixed and to not have to deal with it for years to come, I also replaced the plastic tubing running up the back of the refrigerator, the grommet that goes through the back of the refrigerator into the freezer compartment, and the water tube the pours water into the icemaker's tray - and it was well worth the few extra dollars and 10 extra minutes of work. To do this part:

1. Inside the freezer section, loosen the two screws holding the icemaker to the back of the freezer (you do not need to remove the screws, but it won't hurt anything if you do remove them).
2. Slide the icemaker upward until it clears the two screws enough that you can set the icemaker out of the way.
3. Grasp the 1/2-inch plastic tube that points toward the front of the freezer and pull it toward you until it comes out.
4. At the back of the refrigerator, pull out the plastic grommet that held the tube you just removed, near the top of the refrigerator.
5. Remove the thin water tube that runs from the water valve up the back of the refrigerator to the grommet.

ASSEMBLY:

1. Basically, reverse the order of disassembly.

CONCLUSION:

It took longer to type the instructions than it would have taken to do the job. If only the elctrical connectors had been there the first time.
Other Parts Used:
Dual Inlet Water Valve Icemaker Water Line Fill Tube Grommet
  • Stephen from Raleigh, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench set
94 of 109 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leak from cracked Icemaker Water Line
This repair was done on a 13 year old fridge. Within the last several years I had to replace the Incoming Water Line twice, the line from the Inlet Water Valve to the Dispenser Water Reservoir, and this time the Icemaker Water line. These were all due to the plastic tubing hardening and becoming brittle from the heat of the compressor.

For this repair, I not only replaced the cracked Icemaker Line, I replaced the Incoming Water Line with copper, and replaced the Dispenser Water Reservoir. If you have a leak in one of the plastic water lines around the Valve Assembly, I recommend you do the same.

The Icemaker Water Line instructions from Stephen from Raleigh was very helful and complete.

I found Scot from Fort Collin's instructions on replacing the Reservoir very helpful too. Although I found his comment that one line was too short, to not be the case. In fact I had to trim both lines because they were too long.

Scott from South Lake Tahoe's suggestion to use the old Reservoir Lines to fish the new ones is good. I used duct tape to attach them together instead of drip irrigation fittings, and it worked fine. It helps to have somebody at the back of the fridge to pull the line while you push it from inside the fridge.

The line to the door connection can be accessed by removing the grill at the bottom of the front of the fridge.

Pretty easy repair. Thanks to the other contributors for the help!
Other Parts Used:
1/4 Tubing Nut Icemaker Water Line Fill Tube Grommet Fill Tube Clamp Insert - 5/16 Inch Dispenser Water Reservoir Plastic Tubing - 5/16 Inch
  • Joe from Glenmoore, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
23 of 38 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water spraying in the freezer
It was very simple. From turning off the water and draining the line to unscrewing the controller, disconnecting the line and etc. Putting everything back together was easy as well. Most of my time was spent cleaning below the frig and back.

The only thing I wish I purchased a new hose clamp.
Other Parts Used:
Dual Inlet Water Valve Icemaker Water Line Fill Tube Grommet
  • Amy from Holliston, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
7 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS298725
Manufacturer Part Number: WR2X7927
Brand
Model Number
Description
Kenmore
36350221000
Refrigerator
Kenmore
36350222000
Refrigerator
Kenmore
36350227000
Refrigerator
Kenmore
36350232000
Refrigerator
Kenmore
36350237000
Refrigerator
Kenmore
36350242000
Refrigerator
Kenmore
36350247000
Refrigerator
Kenmore
36358042890
Refrigerator
Kenmore
36358042891
Refrigerator
Kenmore
36358042892
Refrigerator
Kenmore
36358042893
Refrigerator
Kenmore
36358042894
Refrigerator
Kenmore
36358042896
Refrigerator
Kenmore
36358042897
Refrigerator
Kenmore
36358047890
Refrigerator
Kenmore
36358047891
Refrigerator
Kenmore
36358047892
Refrigerator
Kenmore
36358047893
Refrigerator
Kenmore
36358047894
Refrigerator
Kenmore
36358047896
Refrigerator
Kenmore
36358047897
Refrigerator
Kenmore
36358062890
Refrigerator
Kenmore
36358062891
Refrigerator
Kenmore
36358062892
Refrigerator
Kenmore
36358062893
Refrigerator
Kenmore
36358062894
Refrigerator
Kenmore
36358062896
Refrigerator
Kenmore
36358062897
Refrigerator
Kenmore
36358067890
Refrigerator
Kenmore
36358067891
Refrigerator

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service