Part Location Diagram of WR2X7054 GE Push On Nut
See part 415 in the diagram
Replacing your General Electric Dishwasher Push On Nut
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Push On Nut WR2X7054

 Fits your TBX20ZGC!
★★★★★
★★★★★
7 Reviews

Rated by 25 customers 

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

$ 13.82
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your TBX20ZGC!
PartSelect Number PS298353
Manufacturer Part Number WR2X7054
Manufactured by GE for General Electric, Hotpoint, Kenmore
Product Description

Push On Nut Specifications

This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your General Electric Dishwasher Push On Nut

Replacing your General Electric Dishwasher Push On Nut
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Dishwasher, Refrigerator.
Part# WR2X7054 replaces these:
AP2059046, 297552, WD02X0429, WD2X429, WR02X7054
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
7 Reviews
4.7
Filter By Rating:
  • 5 Stars
    5
  • 4 Stars
    2
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 3.0 / 5.0, 25 reviews. What's this?
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing installation instruction that matched.
Leaking water in the shaft seal.
I follow the instruction showing in your video and the replacement was very easy. I am very please that you provided a didactic video. Now the dishwasher is working like new. Thanks.
Other Parts Used:
Push On Nut Drain Valve Shaft Seal
  • Carlos from KISSIMMEE, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Flapper valve leaking at shaft
Followed the sequence from on line video provided by PartSelect. Knowing the sequence and the secret of the push on nut made the replacement simple. My dishwasher is built in therefore I pulled my dishwasher half way out to gain better access and did not need to disconnect drain or water supply. Just unplugged the power and went to work.
Other Parts Used:
Push On Nut Drain Valve Shaft Seal
  • Steven from CAMPBELL, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original Push on nut had corroded and was not retaining seal properly. Leaked water every drain cycle.
I would like to start-off by saying that I love this site . I've never been even remotely dissatisfied with parts I've ordered and the installation videos are awesome! I would recommend this site to anyone looking to repair appliances. Secondly, I am a retired mechanical designer with over 35 years of experience. I have a broad range of design experience in consumer, governmental, industrial and military part and product design. My opinion about the design having to do directly with my appliance is not very high and after talking with another local parts supplier discovered that this particular design is approximately 20 years old. I wonder how many dishwashers are leaking without the consumer realizing they have this problem. I followed the installation instructions provided by this site verbatim and the dishwasher still leaked like a sieve. This in my opinion goes back to my remarks concerning the design. This is a weak design at best and could benefit from an improvement in that area. After I installed the new parts, the push on nut (upon being seated onto the shaft for the drain valve flapper) was loose and spun freely. The push on nut did not properly compress the seal onto and around the flapper shaft nor into the valve housing. Water leaked through the seal as a result. I disassembled all of the parts again and placed a flat washer between the push on nut and the seal, to help compress the seal onto the flapper shaft and into the valve housing. The washer was a stainless steel flat washer with an ID that fit onto the shaft closely, but was a smaller OD than the seal. The washer was about 1/32" thick. Upon reassembly and observation, the dishwasher leak was stopped with the addition of the flat washer and my issue was resolved.
Other Parts Used:
Push On Nut Drain Valve Shaft Seal
  • David from Emmitsburg, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
With non-use the drain control shaft started leaking
As the washer is slightly undersized to perform correctly, following standard instructions to replace the drain valve staff seal and retaining washer I wound Teflon tape between the retaining ring and washer to slightly increase pressure on the washer and seal the opening.
Other Parts Used:
Push On Nut Drain Valve Shaft Seal
  • Jerry from DAVENPORT, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking shaft seal
There was no mention of a very slight rub of silicone for lubrication. I have always utilized this on all "O" rings with good results!
Other Parts Used:
Push On Nut Drain Valve Shaft Seal
  • BYRON from PONCE INLET, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher leaking from solenoid drain valve
Disconnect the power. Unscrew the bottom toe kick panel. Locate the solenoid drain valve to the front left of the machine and disconnect the wired connection. Pry off the retainer clip on the drain valve spindle and set aside for reuse. Plan on getting a new one because you will most likely damage it when removing. Remove the spring from the solenoid valve spindle arm to access one of the three screws holding the solenoid drain valve to the pump. Remove the three screws. Remove the solenoid and plastic housing. Remove the push-on-nut from the spindle by cutting off the old one with wire cutters. Plan on buying a new one because you will never get it off in one piece. Pry out old valve seal with a knife or thin screw driver. Insert new seal and install new push on nut over seal. Important!! make sure the drain valve opens/closes freely by hand because you may have pushed the spindle in to far when installing the push on nut. Place the push on nut in a socket wrench socket with an extension and hammer it on gently or try to start itwith pliers and use a small length of 3/8" copper tubing. Again, check to see if drain valve rotates and pull the spindle in or out with pliers to adjust. Reassemble remaining parts in reverse order. Leak shoud be fixed but check to see if machine drains properly. You may have to dissassemble and adjust the spindle again. This is a difficult repair with the machine left in place. However, it is worth 1-2 hours of your time and for about 20 bucks in parts and shipping. Good luck!!
  • robert from wayne, NJ
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The seal for the drain valve was leaking.
I removed the front bottom panels to give me access to the Solenoid area. I did not take out the dishwasher from the cabinetry. I removed the screws holding the solenoid assembly and the C clip holding the hand fan shaped white nylon thing onto the valve shaft. I slipped these to the side. Then I cut through and removed the push on nut with a wire snipper plier. Then I used a knife blade tip to pick out the black seal. I then slipped the new seal onto the shaft, being careful that the flat side was outward, and slid it down the shaft and , with my fingernail, pushed it completely flush into position. The biggest challenge was the push on nut. It does not push on easily and must have the lips pointed outward. It required the use of a 3/8" diamater tube slipped over the shaft to tap the nut down the shaft. This caused the shaft to push into the pump housing, which caused the valve to bind. So I used a vice grip to pull out on and hold the shaft while I tapped the push on nut with a flat head screwdriver. Then I just reversed the solenoid assembly removal. But , when I ran the dishwasher, it no longer leaked.
Other Parts Used:
Push On Nut Drain Valve Shaft Seal
  • mary from orlando, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking out during rinse cycle
Based on what I read from other people and partselect, it was fairly easy to ascertain what was wrong. I removed the solonoid valve by removing the two screws that held in place. Had to clean up the solonoid valve rod due to water leaking into it by running it on a wire brush. Pulled out the stop nut and old seal and replaced it with the new seal. Could not get the new stop nut on but it does not seem to move so let it go. Have to say that reading all the comments certainly helped me with the repair. Additionally, ordered parts by email at 10:30 in the morning and receiving them the very next day. Could not believe they were delivered so quickly.
Other Parts Used:
Push On Nut Drain Valve Shaft Seal
  • Earl from Holmes Beach, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leak when dishwasher drains
The leak was coming from the drain valve shaft and I found the tips to replace the seal from this website. I was able to reach everything without removing the dishwasher from the cabinet. Once I got the cam lifter off the old push on nut was corroded so it was easy to get off. The old seal was recessed so I used the point of an ice pick to gently pry it out. The new seal was easy to push in place but the push on nut was a bear. I saw other comments about using a deep socket to push it on but I didn't have one the right size. I was able to hold the end of the shaft with pliers and pushed the nut in place using a screwdriver. Ran a short cycle and no more leak. Thank goodness for this website. Found the part easily and the other written comments were very helpful.
Other Parts Used:
Push On Nut Drain Valve Shaft Seal
  • John from Modesto, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Drain shaft seal was leaking.
The solenoid and linkage was easy to disasemble, but getting the retainer (push on nut) off was difficult without removing the motor and pump. Once removed it was a snap. Getting the pump/motor back onto the pipes was near impossible from underneath. I had to remove the dishwasher from under the countertop to get it back correctly. I would reccomend doing this for this repair, as it made life a lot easier. Unwiring and removing the water supply line was not a problem either. WORKS AS GOOD AS NEW!
Other Parts Used:
Push On Nut Corner Tub Baffle - Lower Left Corner Tub Baffle - Lower Right Drain Valve Shaft Seal
  • George from Salem, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench set
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Be the first to ask our experts a question about this part!

You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS298353
Manufacturer Part Number: WR2X7054
Brand
Model Number
Description
General Electric
1200L02
Dishwasher - DISHWASHER
General Electric
3000B10
Dishwasher - DISHWASHER
General Electric
3000W10
Dishwasher - DISHWASHER
Kenmore
361402891
Dishwasher - Kenmore Dishwasher Model 36.1402891 (361402891, 36 1402891) Parts
Kenmore
3631401190
Dishwasher
Kenmore
3631401191
Dishwasher
Kenmore
3631401590
Dishwasher
Kenmore
3631401591
Dishwasher
Kenmore
3631401592
Dishwasher
Kenmore
3631401890
Dishwasher
Kenmore
3631401891
Dishwasher
Kenmore
3631401892
Dishwasher
Kenmore
3631402190
Dishwasher
Kenmore
3631402191
Dishwasher
Kenmore
3631402192
Dishwasher
Kenmore
3631402590
Dishwasher
Kenmore
3631402591
Dishwasher
Kenmore
3631402592
Dishwasher
Kenmore
3631402890
Dishwasher
Kenmore
3631402891
Dishwasher
Kenmore
3631402892
Dishwasher
Kenmore
36314031000
Dishwasher
Kenmore
36314031001
Dishwasher
Kenmore
36314032000
Dishwasher
Kenmore
36314032001
Dishwasher
Kenmore
36314038000
Dishwasher
Kenmore
36314038001
Dishwasher
Kenmore
36314039000
Dishwasher
Kenmore
36314039001
Dishwasher
Kenmore
3631404193
Dishwasher
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service