297808-1-M-GE-WR2X4140 -Dispenser Blade Rest
Part Location Diagram of WR2X4140 GE Dispenser Blade Rest
See part 262 in the diagram
( Grid squares measure 1x1 inch )
297808-1-S-GE-WR2X4140 -Dispenser Blade Rest 297808-2-S-GE-WR2X4140 -Dispenser Blade Rest 297808-3-S-GE-WR2X4140 -Dispenser Blade Rest Part Location Diagram of WR2X4140 GE Dispenser Blade Rest
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Dispenser Blade Rest WR2X4140

Rated by 2 customers 

A Bit Difficult 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 11.02
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS297808
Manufacturer Part Number WR2X4140
Manufactured by GE
Troubleshooting
This part works with the following products:
Refrigerator.
This part works with the following products:
General Electric, Kenmore, Hotpoint, RCA.
Part# WR2X4140 replaces these:
AP2058106, 296560, WR02X4140
Back to Top
Customer Repair Stories
 Average Repair Rating: 1.9 / 5.0, 2 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
bucket drive shaft disengaged from motor drive
This is a 25 year old unit. The ice bucket had warped over time causing the face plate to move forward of its ideal position pulling the entire assembly out of the drive. Removed dispensing unit face assembly. Removed drive shaft assembly. Replaced all washers. Reversed old broken drive cup. Married old drive cup to new drive cup...lining up drive slots. Drilled 6 ea. 3mm holes evenly spaced around circumference into the face of the old drive cup. Fastened drive cups together in vice and with C clamp...then using phillips head screws installed 3 ea. from opposing entry points on each side of this homemade shaft extender. This "mechanism" increased the effective length of the dispensing shaft assembly allowing for a proper fit of the drive shaft to the motor drive connection. Unit now works perfectly. Total cost @ $40.00 and two hours work which would have taken less than one hour if I had remembered to install the ice bucket seal the first time. New ice bucket would have cost @ $185.00. Home warranty does not cover ice makers or any of the associated parts. DIY...it isn't that difficult.
Read less
Other Parts Used:
Ice Bucket Seal Ice Dispensing Drive Cup Roll Pin Dispenser Blade Rest Icemaker Auger Assembly Spacer Blade
  • Paul from Ashton, MD
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
12 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker would not crush ice.
Removed tray from ref. Removed from cover from tray useing a screwdriver. Removed housing, took old parts out. Make sure you take the parts out in order and put new parts back in same order as old parts.
Other Parts Used:
Roll Pin Dispenser Blade Rest Icemaker Auger Assembly Spacer Crusher Stationary Spacer UNKNOWN Rear Moving Dispenser Blade Blade - Middle Front Moving Dispenser Blade
  • Kelly from Canandaigua, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
7 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Be the first to ask our experts a question about this part!

Back to Top
You May Also Need ?
Front Moving Dispenser Blade
$13.02
$13.02
  In Stock
Blade - Middle
$17.05
$17.05
  In Stock
Rear Moving Dispenser Blade
$11.57
$11.57
  In Stock
Blade
$12.60
$12.60
  Special Order
Ice Dispenser Deflector
$9.68
$9.68
  Special Order
Ice Dispenser Plate
$51.49
$51.49
  No Longer Available
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS297808
Manufacturer Part Number: WR2X4140
Brand
Model Number
Description
Kenmore
36350221000
Refrigerator
Kenmore
36350222000
Refrigerator
Kenmore
36350227000
Refrigerator
Kenmore
36350232000
Refrigerator
Kenmore
36350237000
Refrigerator
Kenmore
36350242000
Refrigerator
Kenmore
36350247000
Refrigerator
Kenmore
36350622000
Refrigerator
Kenmore
36350627000
Refrigerator
Kenmore
36357552790
Refrigerator
Kenmore
36357552791
Refrigerator
Kenmore
36357557790
Refrigerator
Kenmore
36357557791
Refrigerator
Kenmore
36358062890
Refrigerator
Kenmore
36358062891
Refrigerator
Kenmore
36358062892
Refrigerator
Kenmore
36358062893
Refrigerator
Kenmore
36358062894
Refrigerator
Kenmore
36358062896
Refrigerator
Kenmore
36358062897
Refrigerator
Kenmore
36358067890
Refrigerator
Kenmore
36358067891
Refrigerator
Kenmore
36358067892
Refrigerator
Kenmore
36358067893
Refrigerator
Kenmore
36358067894
Refrigerator
Kenmore
36358067897
Refrigerator
Kenmore
36358072891
Refrigerator
Kenmore
36358072892
Refrigerator
Kenmore
36358072893
Refrigerator - Kenmore Refrigerator Model 363.58072893 (36358072893, 363 58072893) Parts
Kenmore
36358072894
Refrigerator
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Dispenser Blade Rest
$ 11.02
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.