Bottom Hinge Assembly WR13X10020

Removed old hinge assembly, bolted on new assembly-door shut like new

put block of wood under the door, removed old hinge and installed the new one. about 15 minutes

I replaced both lower hinges without removing the doors. First a couple of observations. The hinge kit consists of two parts; the lower part (bolted to the case) consists of an “L” bracket with a plastic cam, and the upper plastic cam (attached to the door). For some reason the upper cam is available as a separate part . If both cams are plastic both are worn out. Don’t bother ordering the individual cam. If one hinge is worn out the other probably isn’t far behind. Consider replacing both at the same time. Examine the door check. It is an inverted “T” shaped bracket bolted to the door that also holds the door cam. The crossbar of the T are metal tabs that check the door swing. Way too fragile IMO. On mine the refrigerator side was cracked and broke off when I removed it. Since the stops are the same right and left. I just swapped them when I replaced the hinges. Saved $22. Replacing the hinges without removing the doors. {Warning if this technique goes wrong you will be stuck with a loaded door you can’t open.} Remove the vent grill. Stack three 2x4’s along the bottom of both doors ( 26” is about right ). Shim the door(s) up to compensate for the cam wear. About 1/8”) Use a 5/16 socket to remove the hinge from the case. Pay attention to placement of the shims and spacers. Then remove the door cam and stop bracket. Install the new door cam. Leave the screws a little loose. Replace the lower hinge and tighten the screws. Do both sides. Then carefully remove the shims and 2x4’s. Finish tightening the door hinge screws. Check the door swing. I used this technique twice. One to replace the refrigerator side hinge, then again to replace the freezer side hinge and swap the door checks. There were no problems and I saved the hassle of unloading and removing the doors.

Followed the video on the computer. Was fixed in no time. Works great.

Removed the upper hinge assembly. Removed the door. Removed the kick plate. Removed the old hinge assembly and installed the new one.Replaced the other broken cam on the door bottom. Then,reinstalled door to fridge and reinstalled the top hinge. PS/cleaned and lubed both upper and lower hinges.

The on line "how to" video was PERFECT! I followed the steps and the repair was a breeze. Parts Select is now bookmarked in my favorites! These guys make is SO easy for "non-handy" folks like me.

Changed the door stop and hinge assembly. Door works perfectly.

First I diagnosed the problem being a defrost timer as the symtoms are the same as the heater elements. I installed the timer and it worked great for about a week until the frost build up on the evaporator became too much again and then the symtoms returned. I then checked the heater elements and found that both were bad PLUS two clips to the elements were corroded. I then ordered the 2 heater elements. There is more than 1 heater element. Make sure you measure the length of each and then use the graph picture with "Parts Select" on the new ones before you order. There is about a 2" in length difference. Also one comes in a kit with thermostat and wires. Wrong for me. I really wanted that unit as I needed the harness for the bad terminals but it was the wrong heaters and it also came with a new thermostat. Luckly I did not order that one but did order a new thermostat to make sure I did not have to go through this ordeal again. When the parts came I had already replaced the terminals and was ready to go when FedX came. Just make sure you check your heaters before just buying the defrost timer as it may keep you from going back to redo your repair. Just doing your home work before ordering may save you much time in your repair. "PARTS SELECT" was one day on both orders and I just ordered standard shipping. They are great to do business with.

After watching your instruction video and not wanting to shut down refrigerator and remove foods from door, I elected to lift the door and place blocking under it.The actual hinge replacement took approximately 10 mins. I would also like to say that I am extremely satisfied with PartSelects handling of my order and your promptness resending my order because of my goof-up with my own address. I am grateful and will recommend you to anyone who needs parts for any appliance. Thanks again. Chuck Gjovig

I checked the exploded view of the door assembly and the box assembly and determined the parts needed to properly solve the problem. I guessed correctly that the lower cam on the hinge assembly should be replaced at the same time since they had to work together. It ended up I had just the right parts and all of the nut head fasteners were the same size so only one wrench was needed. The door did have to be removed by detaching the top hinge as well.