This part is located behind the control panel. It helps determine the level of water in the washer. As the water fills the hose, while tub is filling, it will push the air against a diaphragm inside the switch. More water that enters the tub, more pressure is applied against the switch.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
General Electric, Hotpoint.
Part# WH12X10076 replaces these:
AP2045906, 771436, WH12X10076
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 5 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer overfilled without shutting off
The actual problem after getting into it was my pressure sensor line that comes off the wash tube was clogged with soap and dirt from years of use. I changed the listed parts as a precaution but make sure you check the line where it meets up at the washer tub not at the switch side. The front of the washer pulls off
Fold back control panel, pull water level knob off, and unlatch pressure switch. reverse procedure to install new switch.
jeff from nahant, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
9 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water coming out of bottom of washing machine
was a toss up between the water inlet valve OR the hose pressure switch....why spend more time...I invested in both the water inlet valve and the hose pressure switch and replaced them both....I have the machine torn apart....I spend $45 more dollars...now it's ALL done....and works like a charm...if I were to isolate the problem...I woul
... Read mored say, now, the hose pressure switch...but, I am happy and machine probably has 5 plus, more years left...and life is good.
took off front control panel, searched the internet for reasons for my problem, replaced the pressure switch, did not fox my problem, replaced the intake valve which fixed the problem.
Mike from Peoria, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
8 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water not shutting off when filling tub and over flowing
First figured out tool to use to remove outer covering on control area. Then unplugged units from electric wiring and replugged with new parts. Parts arrived in a very short time was very pleasantly surprised with the short turn around on ordering and recieving parts.
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kevin
January 21, 2019
Water don't shut off just keeps filling washer
For model number WJRR417OG1WW
Hello Kevin, thank you for your question. Try unplugging the unit when the water is filling the tub. If the valve shuts off and water stops the valve is NOT the issue and you should test or replace the water level pressure switch. If the water continues, replace the valve. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Munkhorgil
December 11, 2017
Water running out from drain hose when water is filling. How to repair this problem.
Hi Munkhorgil,
Thank you for your question. It sounds like the clamps that keep the drain hose in place are not secure and are causing the water to leak out. There is a video on our website that you can reference regarding a drain hose clip. The washing machine may not show exactly like the one you have, but it will give you a general idea on how to install the part. You will find the video under part number PS270508. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
