Timer WH12X1000 | Official GE Part | Fast Shipping | PartSelect
Timer – Part Number: WH12X1000
Timer – Part Number: WH12X1000 Timer – Part Number: WH12X1000 Timer – Part Number: WH12X1000 Timer – Part Number: WH12X1000 https://partselectcom.azureedge.net/Schematics/GE/00107071i01.gif

Timer

Troubleshooting

This part fixes the following symptoms:

Timer will not advance

This part works with the following products:

Washer.

This part works with the following brands:

General Electric, Hotpoint.

Part # WH12X1000 replaces these:

175D2307P013, 278176, AP2045830.
Questions and Answers
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 4 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Roger from South Bend, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WH12X1000
hardest part was getting the knobs off front - there is a small white plastic piece that pops off the shaft and then its easy from there
Remove the plastic piece that holds the timer knob - remove knob - unscrew front panel from top of washer and pull off - remove screws from timer and replace with new and reassemble. Toughest part was removing the timer knob
16 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Stephen from Kunkletown, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable), Wrench set
Parts Used:
WH12X1000
Time was stuck and would not spin
The hardest part of this repair was actually getting the panel off to get at the timer itself. You need a special type of screwdriver with a torc head, (not sure about spelling) ( looks like a phillips head but has an extra "prong") . After that it was as easy as unplugging the old one and plugging in the new one. piece of cake.
10 of 17 people found this instruction helpful.
Was this instruction helpful to you?
stephen from lake forest, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
WH12X1000
tabs holding the timer assy broke off , you could not start the washer with this being loose
It was real easy......
1. removed the 4 phillips head screws from the top of the control panel. The control panel is hinged and pulls forward towards you
2. Holding the Control Panel Chassis at an angle look between the knob and the backing ring for a clear c clip. (Note: you are looking for the open end not the closed end of the clip) Take a small flat blade screwdriver, place it between the timer knob and backing and press down until the clip slides off the spindle.
3. Remove the knob.
4. Before removing the wiring on the timer assy unplug the power cord from the wall socket.
5. Locate the green grounding wire on the timer assy and remove it with pliers.
6. Remove the main control connector by squeezing the tabs.
7. There was only 1 hexhead screw holding my assy to the chassis, remove and carefully pull up the left side of the assy just enough for the timer spindle to exit the chassis.

At this point its just the reverse order to connect the new assy.
9 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Randy from Athens, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WH12X1000
The plastic "ears" on the timer assembly had broken off. So when you tried to turn the knob, it would just spin without contacting the gears.
I first removed the screws from the top of the washer electric panel. Then pulled it forward. I then removed the plastic clip from behind the knob. Then I removed the screw holding the timer in place. And then removed the one single wire and the connecting plug. I then plug both wire assemblies in to the new one, slid both ears under the brackets and inserted the one screw. Then just put the screws back in the top. It works great!!!!!
8 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
1 Review
5
out of 5
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS269722
Manufacturer Part Number: WH12X1000
Brand
Model Number
Description
General Electric
56121T2WW
Washer
General Electric
56121T3WW
Washer
General Electric
56121T4WW
Washer
General Electric
56121T5WW
Washer
General Electric
56121T8WW
Washer
General Electric
56121TAWW
Washer
General Electric
56121TBWW
Washer
General Electric
CCXR1060T5WW
Washer
General Electric
CCXR1060T8WW
Washer
General Electric
CCXR1060TAWW
Washer
General Electric
CCXR1060W0WW
Washer
General Electric
CCXR1060Y0WW
Washer
General Electric
CCXR1060Y1WW
Washer
General Electric
CCXR1060Y2WW
Washer
General Electric
GBSR1080A0WW
Washer
General Electric
GBSR1080A2WW
Washer
General Electric
GBXR1060T2WW
Washer
General Electric
GBXR1060T3WW
Washer
General Electric
GBXR1060T4WW
Washer
General Electric
GBXR1060T5WW
Washer
General Electric
GBXR1060T8WW
Washer
General Electric
GBXR1060TAWW
Washer
General Electric
GBXR1070W0WW
Washer
General Electric
GBXR1070W1WW
Washer
General Electric
GBXR1080A0WW
Washer
General Electric
GBXR1080A2WW
Washer
Hotpoint
HBXR1060T0WW
Washer - Hotpoint Washing Machine Model HBXR1060T0WW Parts
General Electric
HBXR1060T2WW
Washer
General Electric
HBXR1060T3WW
Washer
General Electric
HBXR1060T4WW
Washer