Quick Question!

Have you ever purchased from PartSelect.com before?

268083-1-S-GE-WE4X584           -High Limit Thermostat
268083-1-S-GE-WE4X584           -High Limit Thermostat 268083-2-S-GE-WE4X584           -High Limit Thermostat https://www.partselect.com/Schematics/GE/00008689i04.gif

High Limit Thermostat

Your Price

Order within the next 11 mins and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS268083
Manufacturer Part Number WE4X584
Manufactured by GE

With this high limit/safety thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees Fahrenheit. This element is meant as a safety device, will kick back in when the temperature drops to 210 degrees Fahrenheit. (Limit: 260-50)

This part works with the following brands: General Electric, Hotpoint, Kenmore.

This part works with the following products: Dryer.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Too hot.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.5 / 5.0, 3 reviews What's this?
1-3 of 3

36 of 52 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Screw drivers
Customer: George from Lebanon, TN

Intermittent then no heat

First guess is one of the thermostats. Used ohm meter to test all 5 thermostats. All looked good. (first clue) Bypassed all thermostats, dryer worked. Ordered thermostats. (a couple at a time) Replaced thermostats. Dryer did not work. Tested heating element. Looked good. (Second Clue) Replaced heating element. Still no go! Dryer started working then stopped. Very confused. Ordered timer. Replaced timer. Everything great! Works like a new one. Moral to this story, trust your meter! Should have been a very easy repair. Replaced belt while dryer apart.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

25 of 33 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers, Socket set
Customer: Howard from tallahassee, FL

Totally unpredictable drying temp

Pull the dryer away from the wall, UNPLUG, and remove vent hose. Insert thin metal sheet under the front corners of the lid, push in (hard) while lifting up the lid. The lid will pop up and hinge over and out of the way. Make a drawing of the wiring layout for the lamp and switch on the door, disconect the 3 wires, and remove the entire front panel (2 bolts inside at the top, then lift slightly and pull the panel away). From the back there is a panel for access to the motor/drive belt assy. Remove that panel, reach in, and release the spring loaded pressure on the drive belt. Disengage the Belt. Back at the front of the machine, working inside the drum remove the 3 allen head bolts at the center of the drum. Support the drum - it will drop a little. You can now lift the drum from the front and ease it out with the belt. There is a thermostat at 1 O'clock on the coil rim at the back (2 wires attached to it). To replace, disconnect the 2 wires. Remove the one or two screws, and pull out the thermostat. Install the new thermostat, attach the wires (either way), DONE. Other thermostat is at the bottom in the exhaust duct. Change it the same was as the other, reconnect wires. Remove the belt from the drum and and start working the drum back into the dryer. Loop the new belt over the drum, slide the drum all the way back. I slide 2 long screwdrivers through the screwholes in the drum, and looking down from the top align them with with the holes in the mounting plate. Slide the drum all the way in, reinstall the 3 allen head screws. Reinstall the front panel. Reattach and check all wiring (compare the front panel wiring to your drawing). Lower and snap in the lid. At the back of the unit reach back to the belt and reattach it to the spring assembly. Reinstall that panel, reconnect the exhause duct, slide the unit back and plug in.

Note that the heating problem was the thermostats, but I changed the belt since I was there anyway.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

18 of 30 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Screw drivers, Socket set
Customer: Jose from Dalzell, SC

No heat--dryer runs--timer/heat selector does not advance

Ok so it finally died. Breakdown is relatively easy. UNPLUG the dryer before doing anything else. Remove the dryer vent plastic hose from the dryer--replace if torn. Remove the screws from the back plate covering the switches. Go to the front of the dryer--open door and locate 2 screws at about 11 and 12 o'clock. After removing these 2 screws you should be able to lift the top off the dryer. Take note of the wiring connections--I took a picture of the wiring from my cellphone just in case. Go behind the dryer and locate the access to the electric motor to remove the belt that spins the drum. There is a wheel/belt tensioner--remove the tension from the belt. You are now ready to lift the drum out. While you have this drum out, now is a good time to vacuum all the lint out. Once the drum is out, you'll see the heating element. If the wiring element is broke, just replace the wiring kit not the entire assemby (save $100). While you're at it replace the high limit and safety thermostats (about $28 for both) very easy to replace--unscrew and just replug the wires back to the original terminal locations. To replace the Timer/heat selector, remove a screw that holds the assembly and plug the wires back per your diagram or better if you took a picture from your cellphone. Assemble in reverse direction. Good luck!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3

Model Cross Reference

This part works with the following models:

PartSelect Number: PS268083
Manufacturer Part Number: WE4X584
Brand Model Number Description
General ElectricBJLR473ET0WWDryer - Electric
General ElectricBJLR473EV0WWDryer - Electric
General ElectricBLLR113ET0WBDryer - Electric
General ElectricBVLR333ET0WWDryer - Electric
General ElectricBVLR333EV0WWDryer - Electric
General ElectricCADE165RALDryer - Electric
General ElectricCADE165SALDryer - Electric
General ElectricCADE165SWHDryer - Electric
General ElectricDBLR333ET0AADryer - Electric
General ElectricDBLR333ET0WWDryer - Electric
General ElectricDBLR333ET1AADryer - Electric
General ElectricDBLR333ET1WWDryer - Electric
General ElectricDBLR453ET0AADryer - Electric
General ElectricDBLR453ET0WWDryer - Electric
General ElectricDBLR453ET1AADryer - Electric
General ElectricDBLR453ET1WWDryer - Electric
General ElectricDCCB330ET0ACDryer - Electric
General ElectricDCCB330ET0WCDryer - Electric
General ElectricDCCB330EV0ACDryer - Electric
General ElectricDCCB330EV0WCDryer - Electric
General ElectricDCLR333ET0AADryer - Electric
General ElectricDCLR333ET0WWDryer - Electric
General ElectricDCLR333ET1AADryer - Electric
General ElectricDCLR333ET1WWDryer - Electric
General ElectricDCLR333EV0WWDryer - Electric
General ElectricDDC0580BBLDryer - Electric
General ElectricDDC4307VELDryer - Electric