Ask our experts a question about this part and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Betty
September 26, 2017
Dryer is making loud nose when dryer is on and running. Will the belt fix this problem and should i get the pulley too.
For model number Dbxr463ed2www
Hi Betty,
Thank you for your inquiry. If the dryer is making noise There are some parts that you will need to check to see which one is causing the issue. You will need to check the drum glides or slides, the drum bearings, the drum support rollers and shaft, the drive belt, the idler pulley, the felt drum seal, the blower wheel and housing, the baffles and the motor. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Traci
November 5, 2019
My dryer makes a squealing noise when there is a heavy load and sometimes with lighter loads. I was thinking it is my ideler pulley but i’m not sure
For model number DCVH680EJOBB
Hello Traci, thank you for your question. We would recommend checking the idler pulley wheel, belt, felt seal and the front plastic bearing. It sounds like the heavier loads are putting strain on the drum and causing that noise. I hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Lynn
March 10, 2020
I change the drum belt and the felt belt on the lower door and still makes noise what is the problem
For model number DBLR333EE2WW
Hi Lynn, thank you for your question. There are a few other parts that are more commonly the issue than the ones you listed above. The parts you may need to replace are two of these: PS755842, two of these: PS6447706, and one of this part: PS960316. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Betty
September 27, 2017
The dryer makes a squealing noise very loud. When the dryer is running. Sometimes it stops squealing but starts back up until it finishes.
For model number DBXR463ED2WW
Hi Betty, Thank you for the great question. The noise could be a number of things. First it is good to check the belt. Make sure it is not rubbing or needs to be replaced.While you are checking the belt you can check the Idler Pulley the belt sits on. Make sure the wheel is in good condition and not damaged. You will also need to check the Front Drum Bearing and the Slides. The slides will wear down over time and if not replaced the tabs on the bearing will also wear off and the bearing will need to be replaced with the slides. There is also a Felt Seal that attaches to the bottom half of the drum on the front. This prevent the drum from rubbing and causing the noise as well. If you are replacing the Front Drum Bearing and Slides it is a good idea to replace the Felt at the same time. If all of these parts check out then the problem would be the Rear Drum Bearing Kit. Hope this helps!
Dryer makes a loud noise when drying heavy loads (towels) then as the clothes become dryer the noise stops. Medium to small loads no noise replaced the drum support bearing with glides and slides, new belt, new elt, and replaced the dryer bearing (rear). Saw no visible signs that the idler pulley was bad took the pulley off applied high temp synthetic grease inside pulley and on the arm didn't help. What do you recommend to do next? Thanks, carroll
For model number GE DRYER DBST453EB3WW
Hi Carroll,
Thank you for your question. There are some other parts that you will need to check to see which ones are causing the issue. There is a felt strip in the back of the drum that runs along the bottom of the tub that may have come off. If it came off and moved towards the front of the drum, it can rub against the metal at the front of the dryer and cause this noise. Another part that may cause the noise you are hearing is the motor. If a load of clothes in the dryer is too heavy it can cause strain on the motor and also cause the noise you are hearing. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Scott
November 25, 2022
How to open
For model number GFDR485EFIRR
Hi Scott, thank you for your inquiry. We have researched your model and attached a relevant video that might help you with your problem. We hope this is what you were looking for!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Part Videos
Replacing your General Electric Dryer Idler Pulley Wheel
Customer Repair Stories
Average Repair Rating: 3.1 / 5.0, 16 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
belt broken, pulley worn out
Removed 4 screws from top of control panel , remove 2 from back to lossen top of dryer. Removed rear lower access cover,6 screws on back of dryer exposing pulley and tensioner, remove broken belt and vaccuumed out a ton of lint , removed pulley and tensioner and replaced. From the front remove 4 screws and take off front of dryer, disconnecting several wires, again vaccumed out lint, lifter drum evough to replace belt. Reassembled
Anthony from Mpls, MN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Socket set
66 of 99 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
worn out drum bearing(squeaky)
If you're dis-assembling the dryer panels to remove the drum to acess the bearing located at the rear of the drum,don't hesitate to buy a idler pulley kit and a belt.It's easier to change them now,while it's apart. besides,their all pretty much in the same state of wear! In lew of prying my son away from the computer,an extra set of hands is a help, I used a scrap piece of 4x4 with a 1 inch whole bored in one side to place the bearing end into to steady it to get the screws started. otherwise you need to have 6ft.arms! re-assembly wasn't bad, a magnetic tipped #3 screw driver eliminates the frustration of dropping panel screws down inside the partially assembled body.
I took off the top panel and ran the dryer. I watched as the drum turned more and more slowly until it stopped. I turned it off, and unplugged it. I took off the front panel, simply swinging it to the left like a gate so I didn't have to disconnect any wires, then pulled out the drum. I should have taken the belt off the pulley idler first! Got the drum out and could see the broken idler wheel and the groove on the drum's back post for the O-ring. There is a silicon sheath that goes on this back post - don't lose it if it is still good or you'll have to buy another. Getting the idler wheel off the stem was as simple as using the pliers to turn the nut until it came off. I put the new one on, then put the nut back on. I adjusted the position of the idler pulley so that the belt would not be out of line with the pulley on the motor - I just eye-balled it. I slipped the belt around the drum, put the silicon sheath back on the drum post, then put the o-ring in the groove on the post. Put the drum back in the dryer, lining up the post to go back in the hole was a challenge. Then, getting the belt back on the pulley needed a little muscle to apply the tension needed to allow the belt to get into place. I had one hand in each opening on each side of the drum and did it by feel. I put the front panel back on and did a test run. The drum was turning with force now, not slowing down nor easy to stop by applying resistance with my hand. It was also much quieter. Put on the top panel and done!
Faint Squeek after dryer had been running for an hour or so
It makes it real easy if you have two people!! Put the dryer on it back--You'll need to protect the floor and the warm air exhaust of the dryer. Remove the two screws that secure the top--they are located on the inside upper portion of where the door seats on the front panel. Remove the top Remove the front by removing two screws near the top--one on each side Remove the belt from the idler pulley--note how it comes off Lift drum out of dryer Use the torx bit to remove the bearing If you got the kit it comes w/ the bearing housing--you'll need to disconnect a couple of the wiring harnesses holding the heater--replace the bearing housing This is the perfect time to remove all dust bunnies Re-install everything in reverse order
Belt and pulley both broke. Ordered parts; received 2 days later. Took off front and top, positioned belt, replaced pulley and nut. Parts fit perfectly. Reinstalled covers. Ran dryer. Easy fix.
pulled off door, front panel and rear access panel. unscrewed drum. cleaned every thing. removed and replaced front slides, belt idler pulley and rear bearing. Reassembled everything. Dryer is as quiet as a it was when brand new.
took two screws off the front. They were behind the door. These screws held the top on. Lifted top off and took two screws from the frame holding the front door and panel on. Disconnected three wires and removed front panel. Laid dryer over on right side and removed four screws from bottom and back,two from control panel and removed left side.lifted drum out and removed belt. Removed nut cap and idler pulley wheel. Replaced same. removed three screws holding screen and rear drum bearing to drum. Replaced same. Removed electric heat coils from back and removed receiver for rear drum bearing. Replaced same. Put everything back in reverse order. Works better than new!!
I took the dryer rear and bottom panels off after removing a total of 6 screws . I then put on a new belt and pulley after removing the dryer drum by opening the front door of the dryer unit
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
